P4X400DA/P4X400DAP P4X400DAZ USER'S MANUAL M/B For Socket 478 Pentium 4 Processor NO. G03-P4X40DAR2A Release date: Jan. 2004 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
TABLE OF CONTENT USER’S NOTICE ..........................................................................................................1 MANUAL REVISION INFORMATION ..........................................................................1 COOLING SOLUTIONS ..............................................................................................1 CHAPTER 1 INTRODUCTION OF P4X400DA/P4X400DAP/P4X400DAZ MOTHERBOARD 1-1 1-2 1-3 1-4 FEATURE OF MOTHERBOARD ................................................
USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE P4X400DA/P4X400DAZ MOTHER-BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE.
Introduction of P4X400DA/P4X400DAP/P4X400DAZ Motherboard 1-1 Feature of motherboard The P4X400DA/P4X400DAP/P4X400DAZ motherboard is design for use Intel Pentium 4 Processor in 478 Pin Package Processor with the VIA P4X400 Chipset delivers a high performance and professional desktop platform solution. Which utilize the Socket 478 design and the memory size expandable to 3.0GB. These motherboards use the newest VIA P4X400 Chipset. Supports 533MHz System Bus in data transfer rate.
Design Chipset CPU Socket (mPGA478B Socket) Memory Socket Expansion Slot Integrate IDE LAN (for P4X400DAP/ P4X400DAZ) 1394 (for P4X400DAZ) Audio BIOS Multi I/O ∗ ATX form factor 4 layers PCB size: 30.5x21.0cm ∗ VIA P4X400 North Bridge Chipset ∗ VIA VT8235 South Bridge Chipset ∗ Support Intel Pentium 4 478 Pin package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package processor ∗ Support 1.5G∼2.
The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report Intel Pentium 4 2.
(for P4X400DAZ) LAN PRINT GAME/MIDI PORT PS/2 Mouse PS/2 Keyboard MIC USB COM1 COM2 LINE-IN LINE-OUT ATX 12V Power Conn. K/B Power ON Jumper (JP1) ATX Power Conn. PS2 KB/Mouse Port CPU FAN USB Port CPU Socket PC99 Back Panel DDR SDRAM DIMM x3 VIA P4X400 Chip ATX P6 Power Conn. CD Audio System FAN Front Panel Audio AGP Slot VIA VT8235 Chip Floppy Connector ATA 133 IDE Conn.
JBAT JP1 CMOS RAM Clear Keyboard Power On Enable/Disabled 3-pin Block 3-pin Block P.7 P.7 Connectors Connector ATXPWR ATX12V ATXP9 PS2KBM USB LAN (P4X400DAP/ P4X400DAZ) PARALL AUDIO_GAME COM1/COM2 FDD IDE1/IDE2 Name ATX Power Connector ATX 12V Power Connector ATX P9 Power Connector PS/2 Mouse & PS/2 Keyboard Connector USB Port Connector LAN Port Connector Description 20-pin Block 4-pin Block 6-pin Block 6-pin Female Page P.12 P.12 P.13 P.13 4-pin Connector RJ-45 Connector P.13 P.
2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6. Connect ATX Power cable 7. Power-On and Load Standard Default 8. Reboot 9. Install Operating System 10.
JP1 1-2 closed (Default) JP1 1 1 3 3 K/B Power ON Disable 2-3 closed K/B Power ON Enabled Keyboard Power On Setting 2-3 Install CPU 2-3-1 Glossary Chipset (or core logic) - two or more integrated circuits which control the interfaces between the system processor, RAM, I/O devises, and adapter cards. Processor slot/socket - the slot or socket used to mount the system processor on the motherboard. Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM.
2-3-2 About Intel Pentium 4 478-pin CPU This motherboard provides a 478-pin surface mount, Zero Insertion Force (ZIF) socket, referred to as the mPGA478B socket supports Intel Pentium 4 processor in the 478 Pin package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package technology. The CPU that comes with the motherboard should have a cooling FAN attached to prevent overheating. If this is not the case, then purchase a correct cooling FAN before you turn on your system.
DDR3 (BANK4+BANK5) DDR2 (BANK2+BANK3) DDR1 (BANK0+BANK1) Generally, installing DDR SDRAM modules to your motherboard is very easy, you can refer to figure 2-4 to see what a 184-pin DDR SDRAM module looks like. Figure 2-4 When you install DIMM module fully into the DIMM socket the eject tab should be locked into the DIMM module very firmly and fit into its indention on both sides. WARNING! For the DDR SDRAM CLOCK is set at 133MHz, use only DDR266- compliant DDR Modules.
2-5-2 Assigning IRQs For Expansion Card Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to one use. In a standard design, there are 16 IRQs available but most of them are already in use.
2-5-4 AGP Slot This motherboard provides an AGP Slot, support the 2X/4X AGP VGA card. 2x notch 4x notch AGP SLOT 2-6 Connectors, Headers 2-6-1 Connectors (1) Power Connector (20-pin block) : ATXPWR ATX Power Supply connector. This is a new defined 20-pins connector that usually comes with ATX case. The ATX Power Supply allows to use soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard.
Pin 1 (3) ATX P9 Power Connector (6-pin block) : ATXP9 This is a new defined 6-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 3.3V and 5V voltage to maintain system power consumption. Without this connector might cause system unstable because the power supply can not provide sufficient current for system. GND BLK GND GND 3.3V BLK 3.
(9) Serial Port COM1/COM2 : COM1/COM2 COM1/COM2 is the 9-pin D-Subminiature male connector. The On-board serial port can be disabled through BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS SETUP” section for more detail information. PS/2 Mouse LAN PS/2 USB Keyboard PRINT COM1 GAME/MIDI PORT COM2 MIC LINE-IN LINE-OUT (10) Floppy drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable.
This connector connects to the next set of Master and Slave hard disks. Follow the same procedure described for the primary IDE connector. You may also configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. Pin 1 Secondary IDE Connector • Two hard disks can be connected to each connector. The first HDD is referred to as the “Master” and the second HDD is referred to as the “Slave”.
AUD_RET_L AUD_GND AUD_VCC AUD_RET_R AUDIO 2 10 Pin 1 AUD_MIC AUD_MIC_BIAS AUD_FPOUT_R HP_ON AUD_FPOUT_L 9 Line-Out, MIC Headers +DATA GND OC VCC -DATA VCC +DATA GND -DATA +DATA GND Pin 1 VCC Pin 1 USB2 -DATA +DATA GND OC -DATA USB1 VCC (3) USB Port Headers (9-pin) : USB1, USB2 These headers are used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel.
Pin 1 JW_FP1 SPEAK Pin 1 SPKR NC GND HDLED VCC5 RESET VCC5 HDDLED GND RSTSW NC VCC5 ACPILED PWRBTN GND PWR-LED PWR-BTN System Case Connections (9) Wake On-LAN/Modem Headers (3-pin) : WOL This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card. 5VSB GND WOL NOTE: This feature requires that Wake On LAN or Ring In Wake up is enabled.
(11) IR infrared module Headers (5-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function. IR Pin 1 2 NC VCC5 IRTX GND IRRX 5 6 IR infrared module Headers (12) CD Audio-In Headers (4-pin) : CD_IN CD_IN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector.
2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used. 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual. 4. Turn on your peripheral as following order: a. Your monitor. b.
Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization.
3-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press to accept or enter the sub-menu.
Load Optimized Defaults Use this menu to load the BIOS default values these are setting for optimal performances system operations for performance use. Load Standard Defaults Use this menu to load the BIOS default values for the stable performance system operation that are factory settings for normal use. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. Save & Exit Setup Save CMOS value changes to CMOS and exit setup.
The time format is . Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use Manual to define your own drive type manually.
Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.
Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30. Typematic Delay (Msec) Sets the delay time after the key is held down before is begins to repeat the keystroke. The settings are 250, 500, 750, and 1000. Security Option This category allows you to limit access to the system and Setup, or just to Setup. The system will not boot and access to Setup will be denied if the System correct password is not entered at the prompt.
Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled. Video RAM Cacheable Select Enabled allows caching of the video BIOS, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled.
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software AGP Timing Settings AGP AGP AGP * AGP AGP AGP AGP CPU AGP Transfer Aperture Size Transfer Mode Driving Control Driving Value Fast Write Master 1 WS Write Master 1 WS Read to AGP Post Write Delay Transaction 64M 4X Auto DA Disabled Enabled Enabled Disabled Disabled Item Help Menu Level >> ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults Note: Change these setti
Please refer to section 3-7-1 OnChip Device Function Please refer to section 3-7-2 Onboard Super IO Function Please refer to section 3-7-3 Init Display First This item allows you to decide to activate whether PCI Slot or AGP VGA first. The settings are: PCI Slot, AGP Slot.
Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support. The settings are: Enabled, Disabled.
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software Onboard Super IO Function Onboard FDD Controller Onboard Serial Port 1 Onboard Serial Port 2 UART2 Mode RxD, TxD Active IR Duplex Mode Use IR Pins Onboard Parallel Port Parallel Mode EPP Mode Select ECP Mode Use DMA Enabled 3F8/IRQ4 2F8/IRQ3 Normal Hi, Lo Half IRRX/IRTX 378/IRQ7 SPP EPP1.
The Power Management Setup allows you to configure your system to most effectively save energy saving while operating in a manner consistent with your own style of computer use.
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software Wake Up Events VGA LPT & COM HDD & FDD PCI Master Wake-Up on Ring/LAN Wake-Up on PCI PME Wake-Up on RTC Alarm x Date of Month Alarm x Time (hh:mm:ss) Alarm > IRQs Activities OFF LPT/COM ON OFF Disabled Disabled Disabled 0 0 : 0 : 0 Press Enter Item Help Menu Level >> ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standard Defaults Wake Up On Ring/PME During Disabled, the syste
This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software IRQ Resources IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ12 IRQ14 IRQ15 assigned assigned assigned assigned assigned assigned assigned assigned assigned assigned to to to to to to to to to to PCI PCI PCI PCI PCI PCI PCI PCI PCI PCI Device Device Device Device Device Device Device Device Device Device Item Help Menu Level >> ↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Optimized Defaults F7:Standar
This section is for setting CPU Frequency/Voltage Control. CMOS Setup Utility – Copyright(C) 1984-2002 Award Software Miscellaneous Control CPU Clock Ratio 8X Auto Detect DIMM/PCI Clk Enabled Spread Spectrum Disabled ** Current Host/PCI Clock is 100/33MHz ** Host/PCI Clock at Next Boot is 100/33MHz ** Current DRAM Clock is 133MHz ** DRAM Clock at next Boot is 133MHz AGP VddQ Select 1.5V (Default) +2.5V Select 2.
Load Standard Defaults When you press on this item, you get confirmation dialog box with a message similar to: Load Standard Defaults (Y/N)? N Pressing loads the BIOS default values for the most stable, minimal-performance system operations.
DRIVER & FREE PROGRAM INSTALLATION Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. We call this auto detect software MAGIC INSTALL. MAGIC INSTALL supports WINDOWS 9X/ME/NT4.
IDE : VIA ATAPI VENDOR SUPPORT DRIVER IS USED TO FIXED COMPATIBILITY ISSUE FOR IDE DEVICES AGPVXD : VIA AGPVXD DRIVER IS TO BE INSTALLED, IF YOU ARE USING AN AGP VGA CARD, VIAGART.
5. Click NEXT to Install ATAPI Vender Support Driver 6. Click NEXT to choose enabled DMA Mode 7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9. Click Finish to restart computer 4-2 SOUND Install ALC650 Audio Codec Driver 1. Click SOUND when MAGIC INSTALL MENU appears 2.
3. Click Finish and Restart Windows 4. Click Start→Program→Avance Sound Manager→AvRack. Then AVRACK Windows appears 5. Avance Audio Rack table can play CD, WAV, MID, MP3, AVI, MPG Format File 6. Sound Effect select and KaraOK Mode Function 7. Manual Sound Effect Setting 8. This is 2 channel/4 channel/6 channel speakers output setting NOTE: MAGIC INSTALL will auto detect file path: X:\CODEC\ALCCODEC\SETUP.EXE (for WINDOWS 98SE/ME/NT4.
4-3 LAN Install VIA10/100MB LAN Controller Driver (Only for P4X400DAP/P4X400DAZ) The VIA10/100MB PCI Ethernet Adapter Driver path is X:\VIA\LANDRV 1. Click LAN when Magic Install Menu appear 2. Setup VIA 10/100Mb PCI Ethernet Driver 3. Driver install Finish , Click Yes and Restart 4.
3. Click the Button to start installation 4. Select Program Group name or enter a new group name, click continue to setup and click OK after setup complete 4-4-1 How To Utilize PC-HEALTH 1. Click Program → Winbond Hardware Doctor 2. After executing Winbond Hardware Doctor it → Hardware Doctor the Winbond Hardware supports system voltage, Fan speed and CPU/ Doctor will appears SYSTEM Temperature.
3. After finish Setup you will have a Magic BIOS icon in your screen 4. Double click the Magic BIOS icon you will have this picture, choose from internet you can upgrade BIOS On-line 5. When On-line update BIOS the program will auto-check your BIOS version 6. Click Next if you need update BIOS, after upgrade BIOS, the system will clear CMOS and automatically restart 7. Click Yes if you want to update the BIOS otherwise choose No to exit 8.
4-6 USB2.0 Install VIA USB2.0 Device Driver 1. Click USB2.0 when MAGIC INSTALL MENU Appear 2. When USB2.0 Setup Program Appear, Click NEXT 3. Select Install USB Driver and Click NEXT 4. Select FINISH and Restart your Computer 5. Check device working properly in Device Manager The Path of the file is X:\VIA\VIAUSB20\SETUP.
4-7 PC-CILLIN Install PC-CILLIN 2002 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL MENU appear 2. (1) Click "Install PC-CILLIN" when PCCILLIN 2002 main menu appears, and Click NEXT when "Install Shield Wizard For PCCILLIN 2002" (2) Click Open Manual. you can learn PCCILLIN 2002 how to use 3. This is license agreement, select "I Accept the terms" and Click NEXT 4. 5. Click INSTALL, Start to install the software 6.
7. After PC-CILLIN 2002 complete, Please register your information and get LICENSE KEY from TREND MICRO web site, enter your license key and click FINISH Note : 8. finish register process, we recommend select update item ro download newest engine code and virus code Please install ACROBAT READER, Before you read PC-CILLIN 2002 User Manual, the path at X:\acrobat\ar500eng.
