848PDC/848PDCP USER'S MANUAL M/B For Socket 478 Pentium 4 Processor NO. G03-848PDC Rev:2.0 Release date: July 2004 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
TABLE OF CONTENT USER’S NOTICE ........................................................................................................................... ii MANUAL REVISION INFORMATION..................................................................................... ii COOLING SOLUTIONS............................................................................................................... ii CHAPTER 1 INTRODUCTION OF 848PDC/848PDCP MOTHERBOARD 1-1 FEATURE OF MOTHERBOARD...........................
USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE 848PDC/848PDCP MOTHERBOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE.
Chapter 1 Introduction of 848PDC/848PDCP Motherboard 1-1 Feature of motherboard The 848PDC/848PDCP motherboard is design for use Intel Pentium 4 Processor in 478 Pin Package/Northwood/Hyper Threading / Prescott Processor with the Intel 848P Chipset delivers a high performance and professional desktop platform solution. Which utilize the Socket 478 design and the memory size expandable to 2.0GB.
1-2 Specification Spec Design Chipset CPU Socket (mPGA478B Socket) Memory Socket Expansion Slot & Headers Integrate IDE Integrate Serial ATA Description ∗ ATX form factor 4 layers PCB size: 30.5x21.0cm ∗ Intel 848P Memory Controller Hub (MCH) Chipset ∗ Intel 82801EB I/O Controller Hub (ICH5) Chipset ∗ Support Intel Pentium 4 478 Pin package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package processor ∗ Support CPU Frequency 400MHz/533MHz/800MHz ∗ Support 1.6G∼3.
1-3 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report CPU: Intel Pentium 4 2.
1-4 Layout Diagram & Jumper Setting PS/2 Mouse (For 848PDCP) LAN MIC Magic Duct LINE-IN LINE-OUT PS/2 Keyboard COM1 USB2 USB1 ATX 12V Power Connector SYSFAN2 K/B Power ON Jumper (JP1) CPU FAN Magic Duct CPU Socket PS2 KB/Mouse Port DDR DIMMx2 COM1 Connector USB Power On Jumper (JP5) USB Port ATA 100 IDE Connector USB Port/LAN Connector Audio Connector (CN1) CD Audio ATX Power Connector SYSFAN1 RTL8100C LAN Chip Intel 848P Chip AGP 4X/8X 1.
Jumpers Jumper JP2 JP1 JP5/JP6 Name CMOS RAM Clear Keyboard Power On Enable/Disabled USB Power On Enabled/Disabled Description 3-pin Block 3-pin Block 3-pin Block Page P.6 P.7 P.7 Name ATX Power Connector ATX 12V Power Connector USB Port Connector LAN Connectors Description 20-pin Block 4-pin Block 4-pin Connector RJ-45 Connector Page P.12 P.12 P.12 P.
Chapter 2 Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6. Connect ATX Power cable 7. Power-On and Load Standard Default 8. Reboot 9. Install Operating System 10.
(2) Keyboard/USB Power On function Enabled/Disabled: JP1/ JP5, JP6 When setting Enabled you can using keyboard by key in password device to power on system.
2-3-2 About Intel Pentium 4 478-pin CPU This motherboard provides a 478-pin surface mount, Zero Insertion Force (ZIF) socket, referred to as the mPGA478B socket supports Intel Pentium 4 processor in the 478 Pin package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package technology. The CPU that comes with the motherboard should have a cooling FAN attached to prevent overheating. If this is not the case, then purchase a correct cooling FAN before you turn on your system.
DIMM2 (BANK2+BANK3) DIMM1 (BANK0+BANK1) Generally, installing DDR SDRAM modules to your motherboard is very easy, you can refer to figure 2-4 to see what a 184-Pin DDR266/DDR333/DDR400 DDR SDRAM module looks like. Figure 2-4 NOTE! When you install DIMM module fully into the DIMM socket the eject tab should be locked into the DIMM module very firmly and fit into its indention on both sides. WARNING! For the DDR SDRAM CLOCK is set at 200MHz, use only DDR400compliant DDR Modules.
2-5-2 Assigning IRQs For Expansion Card Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to one use. In a standard design, there are 16 IRQs available but most of them are already in use.
2-5-4 AGP Slot This motherboard provides an AGP Slot, only support the 1.5V 4X/0.8V 8X AGP VGA card. Do not use AGP 2X card (3.3V) in this motherboard. It will burn and damage the motherboard due to Intel® 848 chipset can not support AGP 2X (3.3V). IMPORTANT! Before you plug-in AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has “AGP 4X notch (show below) please make sure your AGP card is AGP 4X/8X (1.5V/0.8V) not AGP 2X (3.
2-6 Connectors, Headers 2-6-1 Connectors (1) Power Connector (20-pin block) : ATXPWR ATX Power Supply connector. This is a new defined 20-pins connector that usually comes with ATX case. The ATX Power Supply allows to use soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard.
(6) Audio Line-In, Lin-Out, MIC Connector : CN1 This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC Line-out : Audio output to speaker Line-in : Audio input to sound chip MIC : Microphone Connector (7) Serial Port COM1: COM1 COM1 is the 9-pin D-Subminiature mail connector. The On-board serial port can be disabled through BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS SETUP” section for more detail information.
IDE1 Pin 1 (10) Secondary IDE Connector (40-pin block): IDE2 This connector connects to the next set of Master and Slave hard disks. Follow the same procedure described for the primary IDE connector. You may also configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. IDE2 Pin 1 • Two hard disks can be connected to each connector.
2-6-2 Headers AUD-RET-L Line-Out, MIC Header (9-pin): AUDIO This header connect to Front Panel Line-out, MIC connector with cable.
(5) IDE Activity LED: IDE LED This connector connects to the hard disk activity indicator light on the case. (6) Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system’s power supply. See the figure below. (7) Power LED: PWR-LED The Power LED is light on while the system power is on.
(10) FAN Headers (3-pin) : SYSFAN1, SYSFAN2, CPUFAN These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan’s plug to the board taking into consideration the polarity of connector. SYSFAN2 1 CPUFAN 1 3 3 SYSFAN1 3 1 FAN Headers (11) CD Audio-In Headers (4-pin) : CDIN CDIN are the connectors for CD-Audio Input signal.
2-7 Starting Up Your Computer 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used. 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual. 4. Turn on your peripheral as following order: a. Your monitor. b.
Chapter 3 Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization.
3-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press to accept or enter the sub-menu.
Load Optimized Defaults Use this menu to load the BIOS default values that are settings for optimal performances system operations. Load Standard Defaults Use this menu to load the BIOS default values that are factory settings for the stable performance system operation. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. Save & Exit Setup Save CMOS value changes to CMOS and exit setup. Exit Without Saving Abandon all CMOS value changes and exit setup.
Time The time format is . Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use Manual to define your own drive type manually.
Anti-Virus Protection Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.
Typematic Rate Setting Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled. Typematic Rate (Chars/Sec) Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30. Typematic Delay (Msec) Sets the delay time after the key is held down before is begins to repeat the keystroke. The settings are 250, 500, 750, and 1000.
Video RAM Cacheable Select Enabled allows caching of the video BIOS, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled. Memory Hole At 15M-16M You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached. The user information of peripherals that need to use this area of system memory usually discusses their memory requirements.
3-7 Integrated Peripherals CMOS Setup Utility – Copyright(C) 1984-2004 Award Software Integrated Peripherals > Onboard IDE Function > Onboard Device Function > Onboard Super IO Function Init Display First Power On Function KB Power On Password Hot Key Power On Power Loss Function Press Enter Press Enter Press Enter PCI Slot Button Only Enter Ctrl-F1 Always Off Item Help Menu Level > ↑ ↓ → ← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F5:Previous Values F6:Optimized Defaults F1:General Help F7:
OnChip IDE Primary/Secondary The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled. Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively increased performance.
Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. The settings are: Enabled, Disabled.
following message will be displayed on the screen: “EPP Mode Select.” At this time either EPP 1.7 spec. or EPP 1.9 spec. can be chosen. 3-8 Power Management Setup The Power Management Setup allows you to configure your system to most effectively save energy saving while operating in a manner consistent with your own style of computer use.
Wake-Up by PCI card /Power On by Ring During Disabled, the system will ignore any incoming call from the PCI card/modem. During Enabled, the system will boot up if there’s an incoming call from the PCI card /modem. Wake-Up on RTC Alarm This function is for setting date and time for your computer to boot up. During Disabled, you cannot use this function. During Enabled, choose the Date and Time Alarm: Date(of month) Alarm You can choose which month the system will boot up. Set to 0, to boot every day.
3-9 PnP/PCI Configuration Setup This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.
3-9-1 IRQ Resources CMOS Setup Utility – Copyright(C) 1984-2004 Award Software IRQ Resources IRQ-3 IRQ-4 IRQ-5 IRQ-7 IRQ-9 IRQ-10 IRQ-11 IRQ-12 IRQ-14 IRQ-15 assigned assigned assigned assigned assigned assigned assigned assigned assigned assigned to to to to to to to to to to PCI PCI PCI PCI PCI PCI PCI PCI PCI PCI Device Device Device Device Device Device Device Device Device Device Item Help Menu Level >> ↑ ↓ → ← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F5:Previous Values F6:Optimized
system will auto shutdown to protect CPU. 3-11 Miscellaneous Control This section is for setting CPU Frequency/Voltage Control.
3-12 Load Standard/Optimized Defaults Load Standard Defaults When you press on this item, you get confirmation dialog box with a message similar to: Load Standard Defaults (Y/N)? N Pressing loads the BIOS default values for the most stable, minimal-performance system operations.
Chapter 4 DRIVER & FREE PROGRAM INSTALLATION Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. We call this auto detect software MAGIC INSTALL. MAGIC INSTALL Supports WINDOWS 98SE/ME/NT4.
4-1 INF install Intel 848 chipset system driver After you have completed the installation of your operation system (WINDOWS 98SE). You will find an UNKNOWN DEVICE in the device manager (START/SETTING/CONTROL PANEL/ SYSTEM/DEVICE MANAGER). You have to install INF driver as shown below: 1. Click INF in the MAGIC INSTALL MENU 2. Click NEXT when Chipset Software Install Utility appears 3. This license agreement appear , click Yes , the readme information appear , click Next 4.
4-2 SOUND install ALC AC97’ Codec Audio Driver 1. Click SOUND when MAGIC INSTALL MENU appears 2. Then auto detect operation system language edition, click OK, start to install DRIVER 3. Click Finish and Restart Windows 4. Click Start→Program→Avance Sound Manager→AvRack. Then AVRACK Windows appears 5. Sound Effect select and KaraOK Mode Function 6. Manual Sound Effect Setting Note: The path of the file For WIN98/NT4.0/WIN2K/XP is X:\CODEC\ALC\SETUP.
4-3 LAN install Realtek LAN Controller Driver WINDOWS 98SE/98ME/2000/XP Setup 1. Click LAN when Magic Install Menu appear 3. 2. Install Realtek PCI 10/100/1000M Fast Ethernet Driver Select YES and Restart your computer X:\RTLLAN\WIN98 (If OS is win9X) 4-4 USB2.0 install Intel USB2.0 Driver Windows 98SE/ME USB 2.0 Driver installation 1. Click USB2.0 when Magic Install Menu appear 2.
Windows 2000/XP USB 2.0 Driver installation Windows 2000 Mothed1 Start Windows 2000 OS and Internet Connect, Select "Windows Update", Select Driver Update, Install Windows2000 USB2.0 Driver Mothed2 Install Windows 2000 Service Pack 4 or later Windows XP Install Windows XP Service Pack 1 or later 4-5 PC-HEALTH install SMART GUARDIAN Software for Hardware Monitoring Device 1. Click PC-HEALTH when MAGIC INSTALL MENU appears 2. Click OK when SMART GUARDIAN INSTALL appears 3.
4-5-1 HOW TO UTILIZE PC-HEALTH 1. Click START/PROGRAMS/ITE SMART 2. You will see a real time report about FAN ACCESSORIES / ITE SMART GUARDIAN SPEED, VOLTAGE and TEMPERATURE System will make a warning if any value is beyond Initial setting value 3. You may re-set temperature and voltage by click OPTION 4-6 MBIOS&DX9 Install BIOS Live Update Utility and DIRECTX9 1. Click Magic BIOS when Magic Install MENU appears 2.
3. After finish Setup you will have a Magic BIOS icon in your screen 4. Double click the Magic BIOS icon you will have this picture, choose from internet you can upgrade BIOS On-line 5. When On-line update BIOS the program will 6. Click Next if you need update BIOS, after auto-check your BIOS version upgrade BIOS, the system will clear CMOS and automatically restart 7. Click Yes if you want to update the BIOS otherwise choose No to exit 8.
9. When choose From Local Driver to update BIOS, you must have the correct BIOS file in your Local Driver 4-7 PC-CILLIN 10. Choose the correct BIOS file to update BIOS Install PC-CILLIN 2004 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL 2. Click NEXT when the "Trend Micro internet MENU appear security" installshield wizard windows appear 3. This is license agreement, select "I Accept the terms" and Click NEXT 4.
5. Click INSTALL, Start to install the software 6. Setup Complete and click FINISH 7. After PC-CILLIN 2004 complete, Please register your information and we recommend select update item to download newest engine code and virus code Note : Please install ACROBAT READER, Before you read PC-CILLIN 2004 User Manual, the path at X:\acrobat\adberdr6_enu_full.
4-8 HOW TO UPDATE BIOS Before update BIOS users have to “Disable”, “Flash Part Write Protect” item which in “Miscellaneous Control” of BIOS SETUP. Otherwise the system the will not allow you to upgrade BIOS by Award Flash Utility. Method 1. Method 2. Use “Magic BIOS” update BIOS in Windows 98 (refer page 40) In DOS Mode STEP 1. Prepare a boot disc. (you may make one by click START click RUN type SYS A: click OK) STEP 2. Copy utility program to your boot disc. You may copy from DRIVER CD X:\FLASH\AWDFLASH.
