601CF USER'S MANUAL M/B For Socket 370 Pentium III Processor NO. G03-601CFR4A Release date: November 2001 Trademark: * Pentium is registered trademark and MMX is a trademark of Intel Corporation, the other names and brands are the property of their respective owners * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
TABLE OF CONTENT USER’S NOTICE .............................................................................. ii MANUAL REVISION INFORMATION ............................................. 1 THERMAL SOLUTIONS.................................................................... 1 CHAPTER 1 INTRODUCTION OF 601CF MOTHERBOARD 1-1 1-2 1-3 1-4 FEATURE OF MOTHERBOARD............................................................... 2 SPECIFICATION ........................................................................
-8-2.1 IRQS ACTIVITY MONITORING ........................................................... 30 3-9 3-10 3-11 3-12 3-13 PNP/PCI CONFIGURATION SETUP........................................................ 30 PC HEALTH STATUS................................................................................. 31 MISCELLANEOUS CONTROL ................................................................ 32 LOAD STANDARD/OPTIMIZED DEFAULTS ....................................... 32 SET SUPERVISOR/USER PASSWORD .......
Manual Revision Information Reversion 4.0 Revision History Fourth Edition Date November 2001 Item Checklist 5 5 5 5 601CF Motherboard Cable for IDE/Floppy CD for motherboard utilities 601CF User’s Manual Intel Processor Family Thermal Solutions As processor technology pushes to faster speeds and higher performance, thermal management becomes increasingly crucial when building computer systems. Maintaining the proper thermal environment is key to reliable, long-term system operation.
Introduction of 601CF Motherboard 1-1 Feature of motherboard The 601CF motherboard is design for use Intel’s new generation Pentium processors, which utilize the Socket 370 design and the memory size expandable to 1GB (using 256Mb technology). This motherboard integrated VGA, Audio, and PC Health Function with Micro ATX form factor to support total solution for today’s computer market.
Spec Design Chipset Clock Generator CPU Socket Memory Socket Expansion Slot & Headers Integrate VGA Integrate IDE Audio BIOS Multi I/O Description ∗ Micro ATX form factor 4 layers PCB size: 24.4 x 19.
The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.
PRINT GAME/MIDI PORT PS/2 MOUSE PS/2 Keyboard USB COM1 VGA LINE-IN MIC LINE-OUT COM2 Connector (JMP1) CPU F.S.B.
JMP1 CPU Front Side Bus Frequency Setting 2x4-pin Block p.7 JBAT1 CMOS RAM Clear 3-pin Block p.8 Connectors Connector Name Description Page ATX ATX Power Connector 20-pin Block p.13 PS1 PS/2 Mouse & PS/2 Keyboard Connector 6-pin Female p.13 USB1 USB Port Connector 4-pin Connector p.14 PRINT Parallel Port Connector 25-pin Female p.14 VGA1 VGA Port Connector 15-pin Female p.14 AGC Audio/Game Connector 3 phone jack+15-pin Connector p.
Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6. Connect ATX Power cable 7. Power-On and Load Standard Default 8. Reboot 9. Install Operating System 10. Install Driver and Utility 2-2 Checking Motherboard’s Jumper Setting (1) CPU F.S.B.
To clear the CMOS, follow the procedure below: 1. Turn off the system and unplug the AC power 2. Remove ATX power cable from ATX power connector 3. Locate JBAT1 and short pins 2-3 for a few seconds 4. Return JBAT1 to its normal setting by shorting pins 1-2 5. Connect ATX power cable back to ATX power connector Note: When should clear CMOS 1. Troubleshooting 2. Forget password 3.
566/128/66/1.5V 566 : CPU internal frequency, where here is 566MHz 128 : the size of L2 cache, where here is 128K 66 : front side bus frequency, where here is 66MHz 1.
has a corner pin for two of the four corners, the CPU will only fit in the orientation as shown. Colden Arrow Intel Pentium III Socket 370 CPU ZIF Socket 370 When you put the CPU into the ZIF socket. No forces require to insert of the CPU, then press the level to locate position slightly without any extra force. 2-3-4 Over clock Running WARNING! This section is for experienced motherboard installer only. Over clocking can result in system instability or even shortening life of the processor.
This motherboard provides two 168-pin DUAL INLINE MEMORY MODULES (DIMM) sites for memory expansion available from minimum memory size over 32MB to maximum memory size of 1GB SDRAM. Valid Memory Configurations DIMM1 DIMM2 System Accept or Not DS/SS DS/SS Accept Accept Accept DS/SS DS/SS DS : Double Sided DIMM Total Memory Min. ∼ Max. 32MB∼512MB 32MB∼512MB 32MB∼1GB SS : Single Sided DIMM NOTE! Make sure the total installed memory does not exceeds 1GB, otherwise the system may hang during startup.
WARNING! Turn off your power when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 2-5-1 Procedure For Expansion Card Installation 1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers. 2. Remove your computer’s cover and the bracket plate on the slot you intend to use. 3. Align the card’s connectors and press firmly. 4.
INT A PCI slot1 PCI slot2 PCI slot3 Onboard LAN Onboard VGA AC97/MC97 Onboard USB IMPORTANT! INT B Shared Shared Not Shared INT C Not Shared INT D Shared Shared If using PCI cards on shared slots, make sure that the drivers support “Shared IRQ” or that the cards don’t need IRQ assignments. Conflicts will arise between the two PCI groups that will make the system unstable or cards inoperable.
(5) (6) (7) Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The Onboard Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS SETUP” section for more detail information. VGA Connector (15-pin female): VGA This connector is for on board VGA display connection only. If you insert any external VGA card in PCI slot, you should have the connection to your VGA card’s connector.
Pin 1 Floppy Drive Connector (9) Primary IDE Connector (40-pin block): IDE1 This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly. Please refer to the documentation of your hard disk for the jumper settings.
2-6-2 Headers (1) COM2 Headers (9-pin header) : COM2 This board has another serial port COM2, it come with cable providing serial port COM2. COM2 Pin 1 Note: Orient the red marking on the COM2 ribbon cable to pin 1 (2) USB Port Headers (9-pin header): USB2 These headers are used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel.
Power switch: PWRIN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system. VCC GND GND GND NC Speaker Reset SW Turbo LED (8) HDLED VCC NC GND Power LED Turbo SW VCC GND PWRIN EXT SMI System Case Connections (9) FAN Speed Headers (3-pin) : JFAN1, FAN2 These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground.
(11) CD Audio-In Headers (4-pin) : CDIN, CDIN-2 CDIN and CDIN-2 are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector. 4 1 4 1 CDIN CDIN-2 CD Audio-In Headers (12) Wake On-LAN Headers (3-pin) : WOL1 This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN card. NOTE: This feature requires that BIOS Wake-Up by PCI Card is enabled.
2-7 Starting Up Your Computer 1. After all connections are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used. 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual. 4. Turn on your peripheral as following order: a. Your monitor. b.
Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization.
The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu/Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press . 3-3 The Main Menu Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen.
Integrated Peripherals Use this menu to specify your settings for integrated peripherals. Power Management Setup Use this menu to specify your settings for power management. PnP/PCI configurations This entry appears if your system supports PnP/PCI. PC Health Status This entry shows your PC health status. Miscellaneous Control Use this menu to specify your settings for Miscellaneous Control.
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Thu, Apr, 26 2001 13 : 45 : 03 IDE IDE IDE IDE Press Press Press Press Primary Master Primary Slave Secondary Master Secondary Slave Enter Enter Enter Enter None None None None Drive A Drive B 1.44M, 3.25 in.
Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table. Activates automatically when the system boots up causing a warning Enabled message to appear when anything attempts to access the boot sector of hard disk partition table. 3-6 Advanced Chipset Features The Advanced Chipset Features Setup option is used to change the values of the chipset registers. These registers control most of the system options in the computer.
items contained in this menu before you try to change anything. You may change the parameter settings to improve system performance. However, it may cause your system to be unstable if the setting is not correct for your system configuration.
3-7 Integrated Peripherals CMOS Setup Utility – Copyright(C) 1984-2001 Award Software Integrated Peripherals > OnChip IDE Function > OnChip DEVICE Function > OnChip SUPERIO Function Init Display First ↑↓→←:Move Enter:Select F5:Previous Values [Press Enter] Press Enter Press Enter PCI Slot +/-/PU/PD:Value F10:Save F6:Optimized Defaults Item Help Menu Level > ESC:Exit F1:General Help F7:Standard Defaults OnChip IDE Function Please refer to section 3-7-1 OnChip DEVICE Function Please refer to section 3
IDE 32bit Transfer Mode Primary Master PIO Primary Slave PIO Secondary Master PIO Secondary Slave PIO Primary Master UDMA Primary Slave UDMA Secondary Master UDMA Secondary Slave UDMA IDE HDD Block Mode IDE Prefetch Mode ↑↓→←:Move Enter:Select F5:Previous Values Disabled Auto Auto Auto Auto Auto Auto Auto Auto Enabled Disabled Menu Level >> +/-/PU/PD:Value F10:Save F6:Optimized Defaults ESC:Exit F1:General Help F7:Standard Defaults 3-7-2 OnChip DEVICE Function CMOS Setup Utility – Copyright(C) 1984-20
Onboard Serial Port 2 UART 2 Mode IR Duplex Mode TX,RX Inverting enable Onboard Parallel Port Onboard Parallel Mode ECP Mode Use DMA Parallel Port EPP Type ↑↓→←:Move Enter:Select F5:Previous Values Auto Normal Half Ho, Yes 378/IRQ7 SPP 3 EPP1.
Doze Mode Suspend Mode ↑↓→←:Move Enter:Select F5:Previous Values Disabled Disabled +/-/PU/PD:Value F10:Save F6:Optimized Defaults Menu Level >> ESC:Exit F1:General Help F7:Standard Defaults 3-8-2 Wake Up Events CMOS Setup Utility – Copyright(C) 1984-2001 Award Software Wake Up Events VGA LPT & COM HDD & FDD PCI Master Modem Ring Resume RTC Alarm Resume x Date (of Month) x Resume Time (hh:mm:ss) > IRQs Activity Monitoring ↑↓→←:Move Enter:Select F5:Previous Values [OFF] LPT/COM ON OFF Disabled Disable
IRQ4 IRQ5 IRQ6 IRQ7 IRQ8 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 (COM 1) (LPT 2) (Floppy Disk) (LPT 1) (RTC Alarm) (IRQ2 Redir) (Reserved) (Reserved) (PS/2 Mouse) (Coprocessor) (Hard Disk) (Reserved) Enabled Enabled Enabled Enabled Disabled Disabled Disabled Disabled Enabled Enabled Enabled Disabled Menu Level >>> ↑↓→← Move Enter:Select Item +/-/PU/PD:Value F10:Save ESC:Exit F5:Previous Values F1:General Help F6:Optimized Defaults F7:Standard Defaults 3-9 PnP/PCI Configuration Setup This section des
into each of the sub menu that follows this field (a sub menu is preceded by a “>”). The settings are: Auto (ESCD), Manual. IRQ Resources When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt. PCI/VGA Palette Snoop Leave this field at Disabled. The settings are Enabled, Disabled. 3-10 PC Health Status This section shows the Status of you CPU, Fan, Warning for overall system status.
CyrixIII Clock Ratio Default Auto Detect DIMM/PCI Clock Enabled Spread Spectrum Disabled ** Current Host Clock is 66MHz ** Host Clock at Next Boot is [66MHz/33MHz] ** Current DRAM Clock is 66Mhz ** DRAM Clock at Next Boot is [66]MHz ↑↓→←:Move Enter:Select F5:Previous Values +/-/PU/PD:Value F10:Save F6:Optimized Defaults Item Help Menu Level > ESC:Exit F1:General Help F7:Standard Defaults Auto Detect DIMM/PCI Clock This item allows you to enable/disable auto detect DIMM/PCI Clock.
of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. ENTER PASSWORD: Type the password, up to eight characters in length, and press . The password typed now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press . You may also press to abort the selection and not enter a password.
properly. We call this auto detect software MAGIC INSTALL. MAGIC INSTALL Supports WINDOWS 95/98/98SE/ME/NT4.0/2000 Insert CD into your CD-ROM drive and the MAGIC INSTALL Menu should appear as below. If the menu does not appear, double-click MY COMPUTER/double-click CDROM drive or click START/click RUN/type X:\SETUP.EXE (assuming X is your CDROM drive). From MAGIC INSTALL MENU you may make 8 selections: 1. IDE install VIA IDE/AGPVXD/IRQ ROUTING/INF driver 2. VGA install on-board VGA driver 3.
IRQ ROUTING : VIA PCI IRQ MINIPORT DRIVER IS TO BE INSTALLED UNDER WIN98 ONLY, IT WILL FIX PCI IRQ ROUTING SEQUENCE INF : VIA REGISTRY DRIVER IS TO BE INSTALLED UNDER WINDOWS THE DRIVER WILL ENABLE VIA POWER MANAGERMENT CONTROLLER 1. Click IDE when MAGIC INSTALL MENU appears 2. Click NEXT when VIA Service Pack Wizard appears 3. This is to announce the Copy Write, click NEXT 4.
5. Click NEXT to Install ATAPI Vender Support Driver 6. Click NEXT to choose enabled DMA Mode 7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9. Click Finish to restart computer NOTE: MAGIC INSTALL will auto detect file path X:\VIA\ This driver supports WINDOWS 95/98/98SE/NT4.0/2000 4-2 VGA Install VIA 8601 VGA Driver A. For WINDOWS 95/98/98SE/ME/NT4.
1. Click VGA when MAGIC INSTALL MENU 2. appears Click NEXT when VIA Display Driver Setup appears 3. Click FINISH to Restart Computer NOTE: The path of the file For WINDOWS 95/98/98SE is X:\VIA\8601VGA\WIN9X\SETUP.EXE For WINDOWS ME is X:\VIA\8601VGA\WINME\SETUP.EXE For NT4.0 is X:\VIA\8601VGA\NT4\SETUP.EXE For WINDOWS 2000 is X:\VIA\8601VGA\WIN2000\SETUP.EXE 4-3 SOUND 1. Install ALC Audio Codec Driver for VIA Click SOUND when Magic Install MENU appears 2.
3. Click Next to Install Avance for VIA Audio Driver 4. When ask Remove old Device Driver, Click OK 5. Click Go 6. Click Finish and Restart windows Note: The path of the file For WIN98/NT4.0/WIN2K is X:\VIA\ALCVIA\SETUP.EXE For WIN95 is X:\VIA\VIAUDIO\SETUP.
4-4 PC-HEALTH Install VIA Hardware Monitor Driver 1. Click PC-HEALTH when Magic Install MENU appears 2. Click NEXT when VIA Hardware Monitor Wizard appears 3. Click Next to install Driver in C:\VIAHM 4. Click Next to use default Program Folders name 4-4-1 How To Use VIA Hardware Monitor Application Software 1.
4-5 MAGIC BIOS Install BIOS Live Update Utility 1. Click Magic BIOS when Magic Install MENU appears 2. Click Next to install the Magic BIOS in Destination Folder 3. After finish Setup you will have a Magic BIOS icon in your screen 4. Double click the Magic BIOS icon you will have this picture, choose from internet you can upgrade BIOS On-line 5. When On-line update BIOS the program will auto-check your BIOS version 6.
7. Click Yes if you want to update the BIOS otherwise choose No to exit 8. 9. When choose From Local Driver to update BIOS, you must have the correct BIOS file in your Local Driver 10. Choose the correct BIOS file to update BIOS 4-6 PC-CILLIN When System programming BIOS don’t turn off power, after finish update BIOS, the system will clear CMOS and automatically Restart Install PC-CILLIN 2000 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL MENU Appears 2.
3. Click NEXT and Enter User Information, Click NEXT or choose BROWSE to change the path For the file to be stored 4. Click NEXT and Choose all Internet Protection 5. Click OK and If You Have Proxy Server, Enter Your Setting. 6. Click NEXT when Start Copy Files, Start to install the software. 7. If you want to make a rescue disc, insert a 1.44 MB disc 8.
9. Enter Your name and E-mail address Register 10. After install PC-cillin 2000 complete we PC-cillin 2000 or Click Cancel recommend select update item to download Register Later newest virus code and setting Auto refresh virus code 4-7 HOW TO DISABLE ON-BOARD SOUND Enter BIOS SETUP choose INTEGRATE PERIPHERALS choose ON-CHIP DEVICE FUNCTION choose AC97 AUDIO Disable on-board sound function by press PAGE DOWN KEY to Disable 4-8 HOW TO UPDATE BIOS Method 1.
