Jetpik Model JP-50/200 Power Floss System
1. Important safeguards. 3 2. Appliance description. 7 3. Getting started. 9 4. Care of your Jetpik unit. 14 5. Troubleshooting. 15 6. Specs 17 7. Limited warranty.
1．Important safeguards. Read all instructions before use Dangers To reduce the risk of electrocution: Do not immerse the charger in water or other liquids,Do not use the charger while bathing. Do not place or store the appliance where it can fall or be pulled into a bath, washbasin or sink. Check the main body of the charger and the cable regularly and if damaged please replace.
The charger for Jetpik is designed to be linked to standard USB output which is 4.75 to 5.25 V DC. Please don’t plug the charger to any other voltage and may cause damage of the equipment. Do not use this appliance if it has been dropped into water or other liquid and is not working properly. Contact Jetpik or your local dealer, which can be found at www.jetpik.com. Do not direct water and floss to any area other than your teeth and gums.
Do not use the adapter outdoors and never force the plug into a mains socket. If the plug does not easily fit into the socket, stop, don’t use it and try an alternative socket or replace with a new adapter. This appliance contains no user-serviceable parts. Contact Jetpik or your local dealer for service if your Jetpik no longer works properly and needs repair. Use this appliance only for its intended use as described in this document or as recommend by your dental professionals.
Medical Warning Consult your dental professional before using this appliance if you have had oral or gum surgery in the preceding two months. Contact your dental professional if excessive gum bleeding occurs after using this appliance or if bleeding continues to occur after one weeks use. Discontinue using Jetpik and contact a physician/dentist if discomfort or pain is experienced. Consult your physician if you have any other medical concerns.
2．Appliance Description.
① Nozzle ② Floss capsule ③ Handle ④ Charger ⑤AC Adapter ⑥Travel case ⑦Water supply tube ⑧UV Sanitizer ⑨ Cup 8
3．Getting Started. Initial Battery Charging. Charge Jetpik for 24 hours before first use. To do so connect the charger to your mains socket and place the handle onto the cradle. A flashing green LED will indicate that the unit is charging and will change to a steady green when the battery is fully charged.
Preparing Jetpik for Use. Before using. ① Place one floss capsule into the nozzle (Note that Jetpik will not work without the floss capsule in position). ② Attach the nozzle to the handle. When using the Jetpik cup supplied - insert the quick connector of the extendable hose on the lower of the cup to the water inlet on the Jetpik handle as shown and pull the tube to a comfortable length and fill cup with water.
Fig1 Fig2 Push Push Prime the floss: Press and move the pressure adjust button to top III position and aim the nozzle into the sink and press the “On/Off” button. Wait a few seconds and when you see water coming out from the nozzle and the floss string coming out from the capsule. Then turn off the unit by pressing the “On/Off” button again.
Using. If you have never used a water irrigator before it is recommended to start at a lower setting by move the pressure adjust button to close to I position. You can gradually increase the pressure providing you don’t experience any gum bleeding or discomfort. Lean over the sink and place the nozzle into your mouth and position the tip towards your teeth and press the On/Off button. Direct the jet stream on to your gum-line as illustrated and move from one tooth to another.
Using the Power brush function (JP200) 1. Clip the power tooth brush head to your Jetpik handle as showing. If you have the jet nozzle on you have to replace it with the brush head. 2. 3. 4. Put comfort amount of toothpaste onto brush and touch your teeth surface. Press on/off button to start the power brush. Press once the button will give you highest strength of power wave to clean your tooth. Press again will give you lower rd strength wave.
4．Care of your Jetpik unit. 1. 2. 3. Empty the cup and keep your Jetpik dry if it is not going to be used for a while. Use tap or pure water to rinse your unit if you have used it to deliver mouthwash or antibacterial solutions. Turn on the unit for few seconds to let the remaining water empty before you put the unit into the traveling case. Using the UV Sanitizer (OPTIONAL) Some models equipped with the UV sanitizer are designed to clean your nozzles and tooth brush heads. 1.
Disposal When the appliance reaches “end of life” and prior to disposal, please remove the rechargeable battery from the handle by knocking and breaking the plastic cover. Then cut the wires to remove the battery from the Jetpik. Now you can recycle or dispose of the battery based on your local regulations. The rest of the unit can be discarded appropriately. N.B.
Jetpik doesn’t start. Battery not charged. Power tooth brush is not running. Instead the handle motor is running Brush tip is not in position or brush motor is dead Don’t see the blue light glows the top window of the UV sanitizer or the green LED is not light up 1. 2. 3. 4. Not connected to power source. The drawer is not fully inserting. Charger is defective. UV sanitizer is defective. Be sure the power charger is functioning and the red LED is on when placed in the cradle.
6．Specs 1. 2. 3. 4. 5. AC Adapter range: 100 to 240 V AC AC Adapter output: 5V, 1000mA min.
7．Limited Two-Year Warranty Jetpik is warranted to the original consumer to be free from defects in materials and workmanship for 2 years from the date of purchase. Consumers will be required to submit the original purchase receipt and the entire appliance to support a warranty claim.
Jetpik® www.jetpik.com Jetpik® is a trademark of Nucreatronics Electronic Technology (Shanghai) Co.,LTD registered in USA, Europe, Brazil, China. Jetpik USA: Ad:16453 Old Valley Blvd. City of Industry, CA 91744, USA. Tel: +1 626-330-0808 Jetpik Europe: 8 Westmayne Industrial Park, Bramston Way, Basildon, Essex.
