This .pdf document is bookmarked Operating Instructions and Parts Manual Manual Pinch Roll Bender Model MPR-10HV JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com Part No.
12. Use the right tool. Do not force a tool or attachment to do a job that it was not designed to do. 13. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on. 1.0 IMPORTANT SAFETY INSTRUCTIONS 14. Give your work undivided attention. Looking around, carrying on a conversation and "horseplay" are careless acts that can result in serious injury. WARNING – To reduce risk of injury: 1.
Familiarize yourself with the following safety notices used in this manual: This means that if precautions are not heeded, it may result in minor injury and/or possible machine damage. This means that if precautions are not heeded, it may result in serious, or possibly even fatal, injury. SAVE THESE INSTRUCTIONS 2.0 About this manual This manual is provided by JET, covering the safe operation and maintenance procedures for the JET Model MPR-10HV Manual Pinch Roll Bender.
.0 Specifications for Pinch Roll Bender Model number ....................................................................................................................................... MPR-10HV Stock numbers: Bender with stand assembly .................................................................................................................. 754430K Bender only ........................................................................................................................................
4.
3. Position machine so there is enough room on all sides for general maintenance and feeding of materials. Anchor machine to a stable floor, preferably concrete, using lag screws or other appropriate fasteners through the holes in stand. Level the machine; use shims if needed. 5.0 Setup and assembly 4. Open shipping container(s) and check for shipping damage. Report any damage immediately to your distributor and shipping agent.
.0 Operation Deburr material to provide a smooth surface, and wipe off any oil on the material. Do not apply excessive pressure to material; use multiple passes to achieve desired bend. For very long materials, use a stock roller stand or similar device to keep workpiece parallel to ground and thus facilitate bending. 1. Install rolls to match desired procedure. 2. Adjust guide rollers as needed. See sect. 6.1. 3. Loosen hex nut at bottom of handle. 4.
9.0 Standard roll dimensions Figure 9-1 10.0 Standard roll profiles and capacities No. Profile type 1 Flat (hard) 2 Flat (easy) 3 Square Tube, solid Tolerance range (in.) Minimum (in.) 0.78 x 0.19 7.5 1.181 x 0.39 19.685 0.78 x 0.19 6.25 1.96 x 0.39 15.748 0.39 6.28 0.78 19.685 1.181 x 1.181 x 0.157 15.748 1.37 x 1.37 x 0.177 23.622 1.181 x 1.181 x 0.157 15.748 1.37 x 1.37 x 0.177 23.622 1.181 x 1.181 x 0.177 19.685 1.574 x 0.787 x 0.196 27.559 1.181 x 0.181 x 0.177 19.
11.0 Roll configurations Examples of material shapes that can be worked using rolls in varied configurations. Figure 12-1 12.0 Replacement Parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.
12.1.
12.1.
.1.
12.1.4 MPR-10HV Manual Pinch Roll Bender – Parts List Index No. Part No. Description Size Qty 1 ................ MPR10HV-01 ............ Stand Assembly ....................................................... ...................................... 1 2 ................ MPR10HV-02 ............ Door ......................................................................... ...................................... 1 3 ................ TS-2360121 .............. Flat Washer .......................................
Index No. Part No. Description Size Qty .................. MRP10HV-62-2 ......... Spacer (not shown).................................................. Ø58 x ø4.7 mm ............. 1 .................. MRP10HV-62-1 ......... Spacer (not shown).................................................. Ø58 x ø5.7 mm ............. 2 .................. MRP10HV-62-4 ......... Spacer (not shown).................................................. Ø58 x ø12 mm .............. 6 .................. MRP10HV-62-3 .........
13.0 Warranty and Service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. • JET products carry a limited warranty which varies in duration based upon the product.
427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.
