Operating Instructions and Parts Manual 16 x 52 inch Foot Shear Model FS-1652J JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com Part No.
1.0 IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS FOOT SHEAR. WARNING – To reduce the risk of injury: 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4.
24. Do not cut rods with the foot shear. 27. Do not exceed rated capacity of the foot shear. 25. Sheet metal stock has sharp edges; use caution when handling to prevent cuts. 28. Do not exceed front gauge capacity – material must not be so long that it interferes in any way with safe operation of the foot pedal. 26. Keep hands and fingers clear of the blade and hold-down area. Do not place hands or fingers between material and table when operating.
3.0 Table of contents Section Page 1.0 IMPORTANT SAFETY INSTRUCTIONS ....................................................................................................... 2 2.0 About this manual .......................................................................................................................................... 3 3.0 Table of contents............................................................................................................................................ 4 4.
4.0 Specifications Model number ......................................................................................................................................... FS-1652T Stock number .............................................................................................................................................. 756202 Capacities: Mild steel...............................................................................................................................................
discard packing material until shear assembled and operating satisfactorily. 5.0 Setup and assembly Read and understand all assembly instructions before attempting assembly. Failure to comply may cause serious injury. 2. Remove bolts holding machine to pallet. Use hoist, forklift, or similar means to lift shear off pallet and move to desired location. 3. Carefully move machine to a level foundation. Machine location must allow access to all sides.
2. 6.3 Blade clearance adjustment Attach back stop (E) to adjustment block flange with M10 screw and flat washer (K,L) from underneath. Blade clearance has been adjusted by the manufacturer for the gauge capacity of the shear. If the shear does not cut properly during operations, identify the specific problem: Place heavy sheet of paper (such as brown craft paper approximately 0.005 in. thick) in cutting position, along entire length of table. Slowly press foot lever.
.0 User-maintenance 8.2 Gib adjustment Lubricate all pivot points on machine daily. Three gib screws (#32, exploded view) can be adjusted for play in each shim. Adjust for smooth travel. Periodically apply light coat of paste wax, or other commercial protectant, to table surface. 8.3 Blade care Additional clevis and cotter pins are provided with the foot shear, should installed ones need replacing due to wear or shearing. Use handling shear blades.
10.1.
.1.2 Parts List: FS-1652J Foot Shear Index No Part No Description Size Qty 1 ................ FS1652J-01............... Table ................................................................... ........................................... 1 2 ................ FS1652J-02............... Cutter Bar ........................................................... ........................................... 1 3 ................ FS1652J-03............... Hold Down .................................................
Index No Part No Description Size Qty 62 .............. FS1652J-62............... Adjusting Dial ...................................................... ........................................... 2 63 .............. FS1652J-63............... Adjusting Screw .................................................. ........................................... 2 64 .............. F009498 .................... Hex Cap Bolt....................................................... M10-1.5x30 ........................
11.0 Warranty and service JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website. • JET products carry a limited warranty which varies in duration based upon the product.
