OWNER'S MANUAL JWCS-10A Cabinet Saw JWCS-10A-PF Shown JET EQUIPMENT & TOOLS, INC. A WMH Company www.jettools.com P.O. BOX 1349 Auburn, WA 98071-1349 e-mail jet@jettools.
Important Information 2-YEAR JET offers a two-year limited warranty on this product LIMITED WARRANTY REPLACEMENT PARTS Replacement parts for this tool are available directly form JET Equipment & Tools. To place an order, call 1-800-274-6848. Please have the following information ready: 1. Visa, MasterCard, or Discover Card number 2. Expiration date 3. Part number listed within this manual 4. Shipping address other than a Post Office box.
14. Keep visitors a safe distance from the work area. WARNING 1. Read and understand the entire instruction manual before attempting assembly or operation. 15. Use recommended accessories; improper accessories may be hazardous. 16. Never place hands directly in line with the saw blade. 2. This table saw is designed and intended for use by properly trained and experienced personnel only.
Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
230 Volt Operation If 230V, single phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. Turn the handwheel until the saw blade is in the 45° position. This will allow easy access to the motor junction box. 3. This tablesaw is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B. 4.
Table of Contents Warranty .................................................................................................................................................2 Warnings.................................................................................................................................................3 Grounding Instructions.............................................................................................................................4 115V Operation ...................
WARNING Read and understand the entire contents of this manual before attempting assembly or operation! Failure to comply may cause serious injury! Contents of the Shipping Container 1 1 1 1 1 1 1 1 2 1 Saw w/ Cabinet Extension Wing Blade Guard Assembly Push Stick Arbor Wrench Miter Gauge Assembly Blade Guard Mounting Bracket Assembly Hardware Bag (blade guard assembly) Handle Assemblies Motor Cover Tools Included for Assembly 1 1 3mm Hex Wrench Arbor Wrench Tools Required for Assembly & Adjustment
WARNING Do not connect the table saw to the power source until all assembly has been completed! Failure to comply may cause serious injury! Installation and Leveling Final location for the saw must be level, dry, well lighted, and have enough room to allow movement around the saw with long pieces of wood. Motor Cover Assembly 1. Install motor cover by aligning pins (A, Fig. 1) brackets on the cabinet. 2. Fasten cover by pulling out latch (B, Fig. 1), closing the door, and releasing the latch.
Hand Wheel Assembly • • Hardware: (2) Handles, (2) Hand Wheels & (2) Lock Knobs Tool: 14mm Wrench 1. Attach handle (A, Fig. 4) to hand wheel (B, Fig. 4). 2. Attach hand wheel assembly to saw with lock knob (C, Fig. 4). 3. Make sure the pin (D, Fig,4) aligns with the notch in the hand wheel. Repeat for second hand wheel.
5. Insert front tab of blade guard splitter through insert opening in table and onto hex cap bolt (A, Fig.7). Hand tighten only at this time. 2. Using a straight edge (B, Fig. 8), align the splitter with the saw blade. Be sure that straight edge rests against body of saw blade and not saw teeth. 6. Insert rear tab of blade guard assembly behind two hex cap bolts, two flat washers and two lock washers (B, Fig. 7) in the upper blade guard bracket. Hand tighten only at this time. 3.
2. To tilt the saw blade, loosen lock knob, turn handwheel (C, Fig. 11) until desired angle is obtained, then tighten lock knob. Table Insert Adjustment • • Hardware: Table Insert Tools: 3mm Hex Wrench, Straight Edge 1. Lower blade completely. 2. Place the open end of the insert under the splitter and lower the insert into the opening. 3. Adjust the table insert flush with the table by turning four leveling screws (A, Fig. 9) and using a straight edge.
5. Tighten the lock nut and reset the pointer. WARNING When making adjustments always disconnect saw from the power source! Failure to comply may cause serious injury! Adjusting 45°° and 90°° Positive Stops • • Hardware: Square Tools: 3mm Hex Wrench, 10mm Wrench 1. Disconnect saw from power source. 2. Raise the saw blade to its maximum height. 3. Set the blade at 90° to the table by turning the blade tilting handwheel counterclockwise as far as it will go. Do not force beyond stop. 4.
3. Lift the motor while taking the belts off the motor pulley. Wear Adjustment in Tilting Mechanism 1. Disconnect the saw from the power source. 4. Let the motor hang from the bracket and remove the belts from the arbor pulley. 2. Loosen lock nut (A, Fig. 15). 5. Replace both belts. 3. Turn eccentric sleeve (B, Fig. 15) until play is removed. Flat area on sleeve accommodates a wrench. 4. Tighten lock nut. Electrical Connections The JWCS-10A table saw is rated at 115V/230V, prewired 115V.
Troubleshooting Trouble Saw stops or will not start Does not make accurate 45°° or 90°° cuts Material binds blade when ripping Saw makes unsatisfactory cuts Blade does not come up to speed Saw vibrates excessively Possible Cause Solution 1. Overload tripped on motor 2. Saw unplugged from wall or motor 3. Fuse blown or circuit breaker tripped 4. Cord damaged 1. Stops not adjusted correctly 2. Angle pointer not set accurately 3. Miter gauge out of adjustment 1. Fence not aligned with blade 2.
Cabinet & Table Assembly 15
Parts List For The JWCS-10A Cabinet & Table Assembly Index Part No. No. Description Size Qty. 1..........290001W ......................... Table............................................................. .................................1 2..........708101............................. Table Insert ................................................... .................................1 3..........TS-1523031 ..................... Set Screw...................................................... M6x10 ......
Index Part No. No. Description Size Qty. 52 ........990805............................. Self Tapping Screw ....................................... M4x10 ......................6 53 ........290122W ......................... Motor Cover .................................................. .................................1 54 ........290124............................. Knob.............................................................. M6 ............................1 55 ........991002........................
Motor & Trunnion Assembly 18
Parts List For The JWCS-10A Motor & Trunnion Assembly Index Part No. No. Description Size Qty. 1..........200035............................. Eccentric ....................................................... .................................1 2..........TS-231014-2 .................... Hex Nut ......................................................... M14x1.5 ...................1 3..........TS-155110 ....................... Lock Washer ................................................. M16 ...............
Index Part No. No. Description Size Qty. 54 ........200102............................. Flange ........................................................... .................................1 55 ........991416............................. Nut ................................................................ 5/8”x12 .....................1 56 ........BB620303 ........................ Bearing.......................................................... 6203LLU...................2 57 ........991172...............
