INSTALLATION INSTRUCTIONS FOR FORD PERFORMANCE MODULE TECHNICAL ASSISTANCE 714-848-5515 JET Performance Products 17491 Apex Circle Huntington Beach, CA 92647 Phone: (714) 848-5515 • Fax: (714) 847-6290 JET P/N 1101 9/07
Information about your... PERFORMANCE MODULE The Jet Performance Module is designed to enhance the performance and driveability of your vehicle. By optimizing the air/fuel ratio, ignition advance and various other parameters, the Jet Module retunes your engine for maximum performance. The use of premium fuel (91 octane or higher) is recommended for maximum results. Lower octane fuels may be used, but could result in lower performance gains.
ECU Location Chart YEAR MODEL LOCATION 87 - 94 Bronco II, Explorer 89 - 03 Cougar, T-Bird 94 - 04 Crown Victoria 05 - 07 Crown Victoria 93 - 98 E Series Van 00 - 05 Excursion All 95 - 02 Explorer 03 & up Explorer, Sport Track 87 - 96 F150, 250, 350, Bronco 04 & up F150, 250, 350 97 - 03 F150, Expedition 97 - 03 F250, 350 94 - 97 F250 - 350 Diesel 98 - 03 F250 - 350 Diesel 06 & up Focus 06 - 07 Freestyle, Five Hundred 03 Marauder 4.
2. Remove negative battery cable. 3. Remove any covers (kick panels, etc.). 4. Remove the ECU mounting bracket screw and pull the ECU out of it's bracket. 5. On the rear of the ECU remove the warranty sticker or plastic cap to expose the connector. IMPORTANT: It is necessary to clean the protective coating off of the circuit board connection on the factory computer.
Module A Photo Instructions t Step 1 t Clean Both Sides! Clean both sides of connector. Step 2 Plug Jet Module onto connector. Step 3 Make sure the module is seated all the way down.
Module A Photo Instructions (Continued) Step 4 Attach the module with the supplied sticker.
Module B Photo Instructions Step 1 t Clean both sides of connector. t Clean Both Sides! Step 2 Plug Jet Module onto connector. Step 3 Make sure the module is seated all the way down.
Module B Photo Instructions (Continued) Step 4 Attach the module with the supplied sticker.
ATTENTION RANGER AND EXPLORER OWNERS On some 1995 thru 2005 models, it may be necessary to remove the ECM stop bracket located directly behind your stock ECM. This bracket is put in by the factory for assembly reasons. It will not affect the vehicle by removing it. This can be done by using a flathead screwdriver and a hammer. Gently tap the corners of the stop bracket. This simple procedure will allow the ECM to stay in its stock position with the JET Power Tech Module attached.
INSTALLATION INSTRUCTIONS FOR 2003-UP FORD EXPLORER/MOUNTAINEER 4.0L 1. Disconnect negative battery cable. 2. Locate the stock ECM (see chart below). 2003 - UP Explorer/Mountaineer 1 #1= Under hood passenger side on firewall 3. Remove the stock wiring harness as in photo #1 4. Install the JET Module using the center bolt to install it to the ECM (photo 2) 5. Reinstall all factory wiring harness into the Jet Module and computer. (As in photo #3) 6. Reconnect battery cable. 7.
Photo #1 Photo #2 Photo #3 10
INSTALLATION INSTRUCTIONS FOR 2004-UP F SERIES 1. Remove the negative side terminal from the battery. 2. Locate your vehicles computer. It is located under the hood in the engine compartment on the passenger side firewall (see photo 2) PHOTO 2 3. On your vehicles computer you will find 3 wiring harnesses, looking at the computer with all three plugs facing you. Unplug the harness on the left by pulling back on the gray release bar.
4. Place the JET Power Control Module with the release tab on top and gently push the module into the computer while keeping the release tab slightly raised until the module seats and the release tab is over and behind the lock tab (see photo 4). PHOTO 4 5. Reinstall the factory wiring harness into the JET Performance Module and push it in firmly to ensure it has good contact and is seated all the way down (see photo 5).
8. Push the grey handle toward the PCM to lock it to the JET Performance Module. NOTE: The handle will not lock unless the factory wiring harness is seated in the JET Module all the way (see photo 6). PHOTO 6 7. Reconnect the negative side battery terminal and start the vehicle. Be sure there are no engine warning lamps illuminated. If you do have an engine warning light or other problems, recheck the installation.
INSTALLATION INSTRUCTIONS FOR 2005-UP FORD MUSTANG 1. Disconnect negative battery cable (see photo 1). PHOTO 1 2. Locate the stock PCM. It is located under the hood on the passengers side and mounted next to the fuse box to the left of the upper radiator hose (see photo 2).
3. Locate the lower connector on the PCM, the one located closest to the ground (see photo 3). PHOTO 3 ➜ 4. CONNECTOR Unplug the lower connector by pulling back on the grey handle of the connector. This will unlock and push the connector out of the PCM (see photos 4 & 5).
PHOTO 5 5. Plug the JET Performance Module into the connector as shown. Make sure you seat the module all the way down until the lock engages (see photos 6 & 7).
PHOTO 7 6. In order to reinstall the harness it is necessary to temporarily remove the harness retainer from its bracket as shown (see photo 8).
7. Reinstall the factory wiring harness into the JET Performance Module and push it in firmly to ensure it has good contact and is seated all the way down (see photo 9). PHOTO 9 8. Push the grey handle toward the PCM to lock it to the JET Performance Module. NOTE: The handle will not lock unless the factory wiring harness is seated in the JET Module all the way (see photo 10).
9. Reinstall the wiring harness retainer that you removed previously (see photo 11). PHOTO 11 10. Reinstall the negative battery cable. 11. Start the vehicle and verify that the SERVICE ENGINE LIGHT IS NOT ON. 12. That's It! Installation is complete. 13.
TROUBLESHOOTING GUIDE... Most computer or module problems are due to poor electrical contacts. If you have a problem, try the following: 1. Disconnect the negative battery cable, unplug the factory harness and the Jet Module. 2. Inspect both the factory parts and Jet Module for any bent or broken pins, dirt or contamination. Fix any minor problems you find. 3. Reinstall the module, harness, battery cable and recheck for the service engine light or any drivability problems. 4.
ASK ABOUT OTHER JET PRODUCTS FOR YOUR CAR OR TRUCK • T.B.
WHAT TO DO BEFORE TAKING YOUR VEHICLE IN FOR SERVICE If a problem occurs that may require you to take your vehicle to a mechanic or dealership for service, first remove the JET Performance Chip or Module and reinstall back to stock. If the problem disappears when you remove the JET Performance Product, call JET and we will troubleshoot the product.
Place this booklet in the glove box along with the vehicle registration and/or warranty The information shown below is provided for future reference Jet PowertechPerformance Products The product for which this document was issued is emission-sensitive and is subject to certain federal and state regulations; the manufacturer has assigned an identification color code designating its intended use.
