® XA4200 XA4300 Amplifier Installation and Operation Introduction Thank you for purchasing a Jensen amplifier. The XA series amplifiers offer extreme value and performance. Proper installation is essential for optimal performance and long-term reliability. Please read through this manual first to familiarize yourself with your amplifier and its functions. Warranty Service If your Jensen amplifier should ever require service, you will need to have the original dated receipt.
® XA4200, XA4300 Contents Features ......................................... 3 Installation..................................... 3 Before You Begin ......................................... 3 Disconnect Battery ........................................ 3 Supplies and Tools Needed .......................... 3 Location and Mounting .................................. 4 Routing Wires................................................ 4 Wiring ............................................. 5 Power ................
® XA4200, XA4300 Features XA Series 4-channel amplifiers include: • Easy access top mounted controls • Continuously variable high pass/low pass crossover • 40Hz – 400Hz crossover frequency range • Crossover mode selector switch • Continuously variable bass boost, centered at 45Hz • Input level control • Remote level control (XA4300) • Traditional input circuitry – low and high level inputs • Pre-amp output for installation flexibility • Dual status LED diagnostic indicator • Thermal, short circuit and lo
® XA4200, XA4300 Location and Mounting The XA amplifier’s compact design allows greater flexibility in mounting. It can be mounted under a seat or in the trunk. When selecting a location, remember that amplifiers generate heat. Select a location where air can circulate around the amplifier. Do not cover the amplifier with carpets or enclose it behind interior trim panels. Do not mount the amplifier in an inverted or upside down configuration.
® XA4200, XA4300 Wiring Power BRIDGE RF GND REM RF – BRIDGE LF LF + RR RR – LR LR + + 12V FUSE Power Terminal (+12V) Remote Terminal (REM) Connect the power antenna/amplifier turn-on lead from the receiver to the AMPLIFIER REMOTE terminal. Connect directly to the vehicle battery+ terminal with 8 gauge wire (minimum).
® XA4200, XA4300 Inputs, RCA Output, Remote Level Control REAR HI-LEVEL XA4200 INPUT XA4300 REAR HI-LEVEL OUTPUT LR LF LF RR RR RF RF LR LR LF LF RR RR RF RF INPUT REMOTE BASS INPUT OUTPUT LR INPUT OUTPUT FRONT HI-LEVEL OUTPUT FRONT HI-LEVEL Input Wiring Radio Low Level Input (RCA Input) Low level (RCA) input is preferred for best performance. Most trunk/hatchback installations will require a 15-20 foot RCA cable.
® XA4200, XA4300 Remote Level Control – Rear Speakers (XA4300) Connecting other Amps INPUT OUTPUT INPUT OUTPUT LR LR LF LF RR RR RF RF PWR MIN MAX REMOTE BASS RCA Output The “output” signal allows you to conveniently connect other amplifiers to each other. Remote level control allows the input level to be adjusted for the rear speakers from an alternate location. It can be mounted under-dash or indash.
® XA4200, XA4300 Speaker Wiring Options 4 Speakers BRIDGE RF RF – 2 Speakers + Bridged Subwoofer LPF FULL HPF X-OVER FRONT REAR LPF FULL HPF X-OVER LPF FULL HPF X-OVER FRONT REAR LPF FULL HPF X-OVER BRIDGE LF LF + RR RR – LR LR + BRIDGE RF RF – BRIDGE LF LF + RR RR – LR 2Ω minimum 2Ω minimum 2Ω minimum 4Ω minimum 2 Subwoofers/Bridged Mono (XA4200) LPF FULL HPF X-OVER FRONT REAR LPF FULL HPF X-OVER BRIDGE RF RF – BRIDGE LF LF + 4Ω minimum RR RR – LR LR + 4Ω minimum 8
® XA4200, XA4300 4 Speakers + 2 Subwoofers BRIDGE LPF FULL HPF X-OVER FRONT REAR LPF FULL HPF X-OVER RF RF – 2Ω BRIDGE LF LF + RR RR – LR LR + Important When running a subwoofer and two full-range speakers together (Trimode operation), high and low pass filters must be used. Failure to install these filters may damage your amp and/or speakers. 2Ω 4Ω 2Ω = 2Ω minimum 4Ω = 4Ω minimum 2Ω 2Ω 4Ω Freq.
® XA4200, XA4300 Indicators and Controls LPF FULL HPF X-OVER BASS L-CH X R-CH X LEVEL FRONT REAR LPF FULL 0dB 12dB 40Hz 400Hz L-CH X BASS 40Hz 400Hz R-CH X MIN MAX LEVEL HPF X-OVER 0dB 12dB 40Hz 400Hz 40Hz 400Hz MIN POWER/ PROTECT 2CH 3CH 4CH MAX Crossover (X-OVER) Adjust the crossover to accommodate your chosen installation method.
® XA4200, XA4300 2CH/3CH/4CH 2 Channel The XA4200/XA4300 can be configured for three different input modes: 4 channel, 3 channel or 2 channel. 2CH 3CH 4CH 4 Channel 2CH 3CH 4CH When the input selector is set to 4 CH, the amplifier will operate as a standard 4 channel amp with all RCA inputs connected. When the input selector is set to 2 CH, the amplifier is configured for bridged stereo operation. The amplifier will need a two channel input even though there are four inputs.
® XA4200, XA4300 Level Bass BASS L-CH X R-CH X BASS LEVEL L-CH X R-CH X LEVEL FRONT REAR FRONT REAR 0dB 12dB BASS 0dB 12dB 40Hz 400Hz L-CH X 40Hz 400Hz 40Hz 400Hz R-CH X 40Hz 400Hz MIN 0dB MAX MIN 12dB BASS LEVEL 0dB MAX The input level control matches the output of your radio to the input of the amplifier. After the installation is complete, make sure the input level control on the amp is turned down all the way (counterclockwise or all the way to the left).
® XA4200, XA4300 Troubleshooting Problem Possible Cause Corrective Action Amplifier does not operate (power LED not on) when vehicle and radio are on No power to +12V terminal Repair wire or connections. No power to remote wire with radio on Check connections to radio with test light. Fuse blown Check fuse. Radio volume needs to be turned up too high for amp to work Input level control adjusted too low Adjust input level control.
® XA4200, XA4300 Specifications XA Series 4-Channel Amplifiers Frequency Response ....................................................................................... 20 Hz-20 kHz ± 0.5 dB Signal to Noise Ratio @ Rated Power .................................................................................... >100 dB Channel Separation @ Ref. Power ............................................................................... >65 dB, 1 kHz THD & IMD @ Ref. Power into 2 ohms ............................
® XA4200, XA4300 Limited One Year Warranty– USA and Canada Length of Warranty. This warranty from Recoton Mobile Electronics shall be in effect for a period of one year from the date of the first consumer purchase. Persons Protected. This warranty will be enforceable by the original owner and any subsequent owners during the warranty period so long as proof of date of purchase from an authorized Jensen dealer is presented whenever warranty service is required. What is Covered.
