Owner's Manual

Steering
Wheel Control
(SWC}
Ready
The recommended
SWC
Interface
is
the
PAC
SWI-RC
steering
wheel control
adapter.
SWI-RC installation hints:
1.
Set
"Radio Select Switch". Set
the
SWI-RC
to
position
7-
"Pioneer/Sony/Other".
2.
Programming -Use the
"Other"
radio function mapping order for Jensen branded head units.
3.
When programming the
SWI
-
RC,
if
a function
is
not
supported (or
not
desired), then the function
MUST
be
skipped
as
per
the
PAC
SWI-RC
instructions.
4.
The
SWC
functions
MUST
also
be programmed in the correct order per the
PAC
SWI-RC
radio function mapping order
instructions.
Disconnect
the
Battery
To prevent a short circuit, be sure
to
turn
off
the ignition and remove
the
negative(-) battery
cable prior
to
installation.
NOTE:
If
the
head unit
is
to
be
installed
in a car equipped with an on-board drive or navigation computer, do
not
disconnect
the
battery cable.
If
the
cable
is
disconnected,
the
computer memory may be
lost. Under
these conditions,
use extra caution during
installation
to
avoid causing a short circuit.
Replacing
the
Fuse
When
replacing
the
vehicles
radio fuse
always
use
the
proper rated
replacement
fuse. Using a fuse with
an
improper rating
could
damage
the
unit and cause a fi
re.
ISO-DIN Installation
The head
unit
is
designed
to
fit
into
a
1.0
DIN
dashboard opening. The
unit
has
threaded holes
in
the
chassis
side
panels
which
may be used
with
the
original
factory mounting brackets
of
some Toyota, Nissan, Mitsubishi,
lsuzu,
Hyundai and Honda
vehicles
to
mount
the
radio
to
the dashboard.
Please consult
with
your local
car
stereo specialty
shop for assistance on this
type
of
installation.
1.
Remove the existing factory radio from
the
dashboard or
center
console
mounting.
Save
all
hardware and brackets
as
they
will
be used
to
mount
the
new
radio.
2.
Remove the factory mounting brackets and hardware from the
existing radio and attach them
to
the new radio.
CAUTION!
Do
not
exceed MS X
6MM
screw size. Longer
screws
may damage components inside
the
chassis.
3.
Place
the radio in front
of
the dashboard opening
so
the wiring
can
be
brought
through the mounting
sleeve. Follow
the
wiring diagram
carefully and make certain all
connections
are
secure and
insulated
with
wire nuts
or
electrical
tape. After
completing
the
wiring connections,
plug
the connector
into
the mating socket on
the
rear
of
the
chassis.
Turn the
unit
ON
to
confirm operation
(vehicle
ignition switch must be "ON").
If
the
unit
does
not
operate, re-check
all
wiring
until
the
problem
is
corrected.
4.
Mount
the
new
radio
assembly
to
the dashboard or center
console
using the reverse procedure in step 1 above.
CAUTION!
Be
careful
not
to
damage
the
car wiring.
Dash Board
Rubber Sheath
NOTE:
It
is
the
end-users
responsibility
to
install
and operate this unit in a manner in accordance with
local, state and
federal
laws.
The
PARKING
BRAKE
wire
MUST
BE
CONNECTED
as
directed in
the
manual.
Using
the
Cosmetic Trim Ring
A cosmetic
trim
ring
is
supplied
with
the head unit for installation flexibility.
This
unit
will
fit
into most
import
dashes
with
little
or
no
modification
to
the
dash board/cavity.
Some
US
domestic
vehicle
dashes
will accept a
Single-DIN
chassis,
but
there
is
usually
a
small
gap between
the
radio and dash piece after installation
is
complete. In
this
case,
use
the
trim
ring
to
conceal
any gaps
that
may be present.
J:]
NOTE:
For proper operation
of
the
CD/DVD player,
the
chassis
must
be
mounted within
30°
of
horizontal.
Make
sure
the
unit
is
mounted within this
limitation.
2