MCD5070 MARINE CD PLAYER / RECEIVER Installation and Operation Manual POWER VOLUME AUDIO MCD5070 SCAN MODE M U TE VOLUME LO U B D A N D 40W x 4 AUX SCN RPT SHF EQ AS/PS
MCD5070 SAFETY INFORMATION DISC NOTES When Driving Compatible Disc Types Keep the volume level Iow enough to be aware of the surrounding. Table 1: General Disc Information Protect from Water Do not expose the product directly to water, as this can cause electrical shorts, fire or other damage. Disc Type Diameter/ Playable Sides Logo Protect from High Temperatures Audio CD Exposure to direct sunlight for an extended period of time can produce very high temperatures inside mobile unit.
MCD5070 INSTALLATION 6. Before You Begin 7. 1. 2. Disconnect Battery Before you begin, always disconnect the battery negative terminal. Remove Transport Screws 8. Important Notes • • • • • • • • 9. Before final installation, test the wiring connections to make sure the unit is connected properly and the system works. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
MCD5070 DIN Rear Mount (Method B) This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some vehicles to mount the radio to the dashboard. Please consult with your local mobile stereo shop for assistance on this type of installation. 1. 2. 3. 4. 5. Remove the existing factory radio from the dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new radio.
MCD5070 WIRING ANTENNA EXTENDER CABLE ANTENNA JACK FUSE 20-PIN AUDIO/POWER HARNESS (See Figure 1) RCA-TO-RCA CABLE (not supplied) WHITE L-CH REAR LINE OUT GREY R-CH RED AMP Figure 1: 20 PIN HARNESS PIN CHART BLUE BLACK Power Antenna Connect to power antenna or amplifier, If not used, tape bare end of wire. Ground Connect to ground terminal or clean unpainted metal part of chassis. RED Accessory / Ignition Connect to existing radio wire or radio fuse.
MCD5070 BASIC OPERATION 1 2 7 4 • • • 19 22 initial installation of the unit when all wiring is completed function buttons do not operate error symbol on the display Reset Back Up Memory The unit is supports after IGN off memorize the operation set up, like last play radio station, preset store stations,etc To resume the back up memory by pressing “MODE+M1” together POWER VOLUME MCD5070 AUDIO Audio Menu SCAN MODE Press the AUDIO button (4) on the control panel to access the Audio Menu.
MCD5070 TUNER OPERATION 1 7 4 Automatically Store / Preset Scan (AS/PS) 2 Automatically Store 19 22 Select a band (if needed). Press AS/PS (16) on the control panel for more than three seconds to automatically select six strong stations and store them in the current band. The new stations replace any stations already stored in that band. Preset Scan POWER VOLUME Select a band (if needed). Press AS/PS (16) to scan stations stored in the current band.
MCD5070 CD OPERATION 1 2 7 4 19 22 POWER VOLUME MCD5070 AUDIO SCAN MODE VOLUME M U TE LO U B D A N D 3 8 6 21 40W x 4 AUX SCN 5 9 10 RPT 11 SHF 12 13 14 EQ AS/PS 15 16 18 20 17 Insert and Eject Disc Insert a disc, label-side up, with the unit turned on. “CDP PLAY” will display on the LCD for about 5 Seconds and the unit will play the first track on the disc. Press the eject button (2) to stop disc play And eject the disc.
MCD5070 SPECIFICATIONS TROUBLESHOOTING CD Signal to Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 70dB Sampling Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.1Khz Quantization Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 bit Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MCD5070 ASA Electronics Corporation www.asaelectronics.com © 2006 ASA Electronics Corporation v.
