CD1211 Owner's Manual AM/FM/CD Receiver CD1211 CD RECEIVER MONO TUNE EQ / SCAN AUX IN
CD1211 PREPARATION Getting Started Congratulations on your purchase of the Phase Linear CD1211 Mobile AM/FM/CD Receiver. It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Phase Linear CD1211 installed by a reputable installation shop. customer support line at 1-800-323-4815. (U.S.A. and Canada only.) Tools and Supplies Disconnect Battery Before you begin, disconnect the battery negative terminal.
CD1211 INSTALLATION INSTRUCTIONS This unit is designed for installation in cars, trucks and vans with an existing radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialty shops. Always check the kit application before purchasing to make sure the kit works with your vehicle. Universal Installation Using Mounting Sleeve 1. 2. Pre-installation 1.
CD1211 9. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard, either above or below the radio, using the screw and hex nut provided. Bend the strap, as necessary, to position it. CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration. 10.
CD1211 Remove Radio To remove the radio after installation, remove the trim ring by lifting in the center and pulling it off from either side. Insert the removal keys straight back until they lock, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit.
CD1211 WIRING 1. 5 15 Power Antenna (dark blue wire) - Connect to power antenna or amplifier. If not used, tape bare end of wire. 2. Accessory/Ignition (red wire) - Connect to existing radio wire or radio fuse. 3. Ground (black wire) - Connect to ground terminal or clean, unpainted part of chassis. 4. Memory/Battery (yellow wire) - Connect to battery or 12 volt power source that is always live. The radio will not work if this wire is not connected. 5.
CD1211 OPERATING INSTRUCTIONS Power Select Press the power button (1) or any other button on the face of the receiver to turn the unit on when the ignition switch is on. Press the power button again to turn the receiver off. If the radio was left on when the ignition was last turned off, the receiver will turn on automatically when the ignition switch is again turned on. If the receiver was off when the ignition was last turned off, the receiver must be turned on manually when restarting the vehicle.
CD1211 Balance X-BASS (BAND) Equalizer Selector (EQ) Press the AUDIO CONTROL button (4) four times until “BAL” appears in the display. Within five seconds, turn the AUDIO CONTROL (3) clockwise (or counter clockwise) to adjust Balance between the right and left speakers from “BAL 10R” (full right) to “BAL 10L” (full left). “BAL L=R” represents an equal balance level between the right and left speakers. The balance position is shown on the display for five seconds or until another function is activated.
CD1211 Display (D) Front Panel Release When the unit is off, the LCD displays the time of day. When the unit is on, the LCD automatically shows the tuner or CD display, depending on which mode of operation is currently activated. The front panel release button (10) releases the mechanism that holds the front panel to the chassis. Display Clock During tuner or CD operation, press D (9) to display the time of day. After five seconds, the display reverts to tuner or CD display. Set Clock 1.
CD1211 TUNER OPERATION AM/FM Band Selector (BAND) Scan Tuning (SCAN) Preset Stations Press BAND (5) during radio play to switch between three FM bands and one AM band. “F1”, “F2”, “F3” or “AM” will appear in the display to indicate the band currently selected. Press SCAN (15) to scan upwards through all the strong channels in the current band. The unit will pause and play each station for five seconds, and the station frequency will flash in the display during this time.
CD1211 Repeat for the remaining five presets on the current band and for all presets on the other three bands. Automatically Store / Preset Scan (AS/PS) Automatically Store Select six strong stations and store them in the current band using the Automatic Store feature. To enable this feature, press and hold AS/PS (17) for more than two seconds. The radio will automatically scan the band in use and enter strong stations into the preset memory positions for that band.
CD1211 CD PLAYER OPERATION Insert CD With the label surface facing up, gently insert the disc into the CD slot (21) until the softloading mechanism engages and pulls the disc in. Disc play begins, “CDP PLAY” will appear in the display, and the CD icon will become animated. The center of the disc icon (7) illuminates and becomes animated and the track number and elapsed time appear in the display. NOTE: The unit is designed for play of standard 5” (12 cm.) compact discs only. Do not attempt to use 3” (8 cm.
CD1211 Disc Repeat (RPT) CD Player Error Codes Press RPT (25) during disc play to continuously repeat the selected track. “S--RPT” will appear in the display. Press RPT again to stop repeating. “S--RPT” will disappear from the display, and regular play will resume. The repeat function will also be canceled when activating the scan or shuffle functions. If a problem should develop while operating the CD player, an error code (ER-1, ER-2, etc.) may appear on the display panel.
CD1211 REMOTE CONTROL The remote control will allow you to control the basic functions of the CD1211. The remote control sensor is located on the left side of the front panel to the right of the MONO button (18). S AMS = AS/PS PEQ = EQ MOD = MODE LOC = Local/Distant BND = BAND SCN = Scan, AM, FM MUT = MO = MONO DISP = Clock / Frequency VOL VOL D U TR. DN LOUD TR.
CD1211 CARE AND MAINTENANCE CD Player Compact Discs The following guidelines will help you extend the life of your CD player: CD-R / CD-RW 1. 2. 3. 4. 5. When cleaning the vehicle interior, do not get water or cleaning fluids on the unit. The CD player will not operate properly in extreme hot/cold or under damp conditions. In case of such conditions, wait until the vehicle interior reaches a normal temperature or any condensation on the disc player lens has evaporated before using the player.
CD1211 TROUBLESHOOTING Problem Does not operate (display does not light) Cause Corrective Action No power to yellow wire; no power to red wire Check connection with test light; check vehicle fuse with test light. Inline fuse blown Replace fuse. No power to unit Inline fuse blown Check/replace fuse. Not all speakers operate Incorrect splices or connections Check all splices and connections. Speaker wires shorting to chassis ground or to each other Check splices; insulate all bare wires.
CD1211 SPECIFICATIONS CEA Power Ratings AM Tuner Tuning range: 530kHz-1710kHz Sensitivity @ 20dB signal to noise: 30uV Frequency response: 50Hz-2kHz., -3dB Auxiliary Input Input sensitivity: 400mV RMS for 1 watt RMS into 4-ohms Frequency response: 20Hz to 20kHz, -3dB Input impedance: 10 k-ohms Power output: 13 watts RMS X 4 channels into 4-ohms @ < 1% THD+N Signal to noise ratio: 70dBA below reference.
Limited Warranty DO NOT RETURN THIS PRODUCT TO THE STORE CD or Multimedia Radios/Headunits Audiovox Electronics Corporation (“the Company”) is committed to quality and customer service, and are pleased to offer you this Warranty. Please read it thoroughly and contact the Company at 1-800323-4815 with any questions. Who is covered? The Company extends this warranty to the original retail purchaser of products purchased through an authorized Audiovox retailer in the U.S.A., Puerto Rico or Canada.
Audiovox Electronics Corporation 150 Marcus Boulevard Hauppauge, NY 11788 1-800-323-4815 www.audiovox.com ©2007 Audiovox v.
