JE1908 19” HD FLAT PANEL LCD TV OWNER'S MANUAL
SAFETY PRECAUTIONS WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS UNIT.
IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
TABLE OF CONTENTS SAFETY PRECAUTIONS ...................................................................................... 2 IMPORTANT SAFETY INSTRUCTIONS ............................................................... 3 REMOTE CONTROL ........................................................................................... 5 ACCESSORIES ..................................................................................................... 5 REMOTE CONTROL REFERENCE GUIDE ..................................
REMOTE CONTROL USING THE REMOTE CONTROL • • • Point the remote control at the REMOTE SENSOR located on the unit. When using this unit in very bright light, the infrared REMOTE CONTROL SENSOR may not work properly. The recommended effective distance for using the remote control is about 16 feet (5 meters). TO CHANGE THE REMOTE CONTROL BATTERY 1. Open the battery door. 2. Insert two “AAA” batteries.
REMOTE CONTROL REFERENCE GUIDE 4) 1 2 11 5) 3 12 6) 4 5 13 6 14 7 15 8 9 16 17 8) 10 18 9) 7) 10) 11) 12) 13) 1) 2) 3) FUNCTION Button Press to switch between TV / AV IN / YUV IN / PC IN. PICTURE Button Press to select from preset screen display settings to match the type of show you are watching (Standard, Dynamic, Personal, Soft & Movie) Number (0 - 9 and dot) Buttons In DVD mode, use when creating programs and locating a title/chapter or specific time.
UNIT REFERENCE GUIDE 1) Color LCD Screen 2) STANDBY Indicator Indicates whether the unit is ON or in STANDBY (OFF) mode. Light On: The unit is in STANDBY. Light Off: The unit is turned ON. REMOTE CONTROL SENSOR Do not block this sensor or remote control will not work. 3) Removable Base Stand 4) STANDBY/ON Button Turns the unit on and off. 5) MENU Button Enters and exits the TV menu. 6) FUNCTION Button Selects TV, AV IN, YUV IN or PC IN.
CONNECTIONS CONNECTING A TV ANTENNA/CABLE/SATELLITE To view television channels correctly, a signal must be received from one of the following sources: - An indoor or outdoor aerial antenna - A cable system - A satellite system Connecting a Digital Antenna The tuner in this TV receives ATSC TV signals from an antenna. This digital TV can receive standard (SDTV) and high definition (HDTV) over the air broadcasts.
CONNECTIONS CONNECTING TO A/V DEVICES (VCR, PVR, Camcorder, Game System, etc.) Connecting to Devices with an S-Video Output To connect to A/V devices such as a VCR or camcorder: - Connect to a VCR Connect the right (red) and left (white) audio output from the VCR to the right (red) and left (white) input on this unit (Audio cable not included). Connect the S-VIDEO output from the VCR to the S-VIDEO input on this unit (S-VIDEO cable not included).
CONNECTIONS Connecting to Devices with a Composite (yellow RCA-type) Video Output To connect to A/V devices such as a VCR or camcorder: - Connect to a VCR Connect the right (red) and left (white) audio output from the VCR to the right (red) and left (white) input on this unit (Audio cable not included). Connect the video (yellow) output from the VCR to the video input on this unit (Video cable not included). Make sure you connect both audio and video from the same VCR to the same input (AV IN).
CONNECTIONS Connecting to Devices with a Composite (yellow RCA-type) Video Input To connect to A/V devices such as a VCR, PVR or camcorder: - Connect to a VCR/PVR Connect the right (red) and left (white) audio input from the VCR/PVR to the right (red) and left (white) output on this unit (Audio cable not included). Connect the video (yellow) input from the VCR/PVR to the video output on this unit (Video cable not included).
CONNECTIONS CONNECTING A HIGH-DEFINITION (HD) SOURCE High-Definition (HD) Devices with component video output must be connected to the YUV input. Connect the three video outputs (Y, Pb, Pr) from the source to the corresponding video inputs on this unit (Component video cable not included). Connect the right (red) and left (white) audio output from the source to the right (red) and left (white) input on this unit (Audio cable not included).
POWER SUPPLY USING THE CAR POWER ADAPTER The car power adapter allows the unit to be used with vehicles that have a 12V, negative ground electrical system. Cautions: • Use the provided car power adapter only. Use with other car power adapters could damage the unit. • The car power adapter included with this unit is for its use only. Do not use it with other equipment. • In the interest of traffic safety, do not operate this unit or view videos while driving a vehicle.
INSTALLATION REMOVING THE BASE STAND WARNING: The LCD Display is very fragile, and must be protected at all times when removing the base stand. Be sure that no hard or sharp, or anything that could scratch or damage the LCD display, come in contact with it. Do NOT place pressure on the front of the unit at any time because the screen could crack. 1. Disconnect any cables or cords connected to the unit. 2.
USING HEADPHONES • Turn down the volume before connecting headphones to the unit, then adjust the volume to your desired level. • When headphones are connected, no sound will come from the front speakers. Note: • Avoid listening to sound at high levels for prolonged periods of time. This may be harmful to you and may cause hearing loss. UNIT OPERATION TURNING THE UNIT ON FOR THE FIRST TIME The first time for you turning on the unit, the unit will enter Virgin mode.
TV SETUP VIDEO MENU 1. Press the MENU button. button to select Video. 2. Press the ENTER or or button to select the options (Picture Mode, Brightness, Contrast, Saturation, 3. Use the or button (The screen Tint, Sharpness or Color Temperature). Adjust them using the button to go into the detailed will change to your desired setting); or press the ENTER or settings. 4. Press the EXIT button to return to the previous menu. 5. Repeat steps 3 and 4 to adjust other options. 6.
TV SETUP VGA Settings in PC Mode Use the or button to select the options (Auto Adjust, H. Position, V. Position, Phase or Clock). Adjust them using the or button. The screen will change to your desired setting. (Press button to confirm Auto Adjust.) the ENTER or Video Auto Adjust Audio Setup H. Position 50 V. Position 50 Phase 3 Clock 127 Parental Best definition 1440 x 900 - Resolution : 1,440 x 900 max Refresh Frequency : 60Hz max • ENTER Enter Select EXIT Return H.
TV SETUP TV MENU (For TV Mode Only) Tuner Mode Cable 1. Press the MENU button. Auto Scan 2. Use the or button to select TV. Press the Auto Scan Add CH Channel Skip ENTER or button to go into the TV settings. MTS Stereo or button to select the options 3. Use the Audio Language English (Tuner Mode, Auto Scan, Auto Scan Add CH, Channel Skip, MTS or Audio Language). Adjust or button (The screen will them using the change to your desired setting); or press the ENTER or button to go into the detailed settings. 4.
TV SETUP TV MODE AV / YUV MODE PC MODE • OSD Language : Select from English / Español / Français.
TV SETUP Caption Setting: Video Audio Analog Closed Caption Off Digital Closed Caption Off Video Caption Style Font Size Audio Digital Caption Style Font Style Font Color TV TV Setup Setup Parental Parental Font Opacity Background Color Background Opacity Window Color Window Opacity Caption Digital Caption Style Select EXIT Return EXIT Return • Analog Closed Caption : Select the analog closed caption or turn it off.
TV SETUP Parental Control Setting: 4. Use the or button to select various Parental settings. Press the ENTER or button to go into the detailed settings. 5. Use the , , and buttons to move among the rating levels. Press the ENTER button to change the mode between Blocked and Allowed. 6. Press the EXIT button to return to the previous menu. 7. Repeat steps 4 - 6 to adjust other options. 8. To exit the MAIN MENU and return to the normal screen, press the EXIT button repeatedly.
TROUBLE SHOOTING GUIDE SYMPTOM CAUSE (AND REMEDY) No power. • Check that the AC power adapter is connected. • Turn on the unit. The remote does not function. • • • • Bad Picture (snow, multiple images, distortion, blurry) • Check the location of the antenna and adjust it if neccessary. • Make sure the antenna cable is connected firmly. • Make sure all input cables are firmly connected. No sound. • Increase the volume. • Check whether the mute function has been activated on the Remote Control.
Unit : INCH 4 1/2 21 15 1/2 7 3/8 12 1/2 23 PLV36190CS1_IB_ENG_JEN.
811-361991Wxxx PLV36190CS1_IB_ENG_JEN.
