Owner's Manual

ManualsBrandsJensen Heavy Duty ManualsGPS & car accessoriesJensen

AUX 1

HDM I USB

Installation and Owner's Manual

MOBILE AUDIO SYSTEM

JWM90A

Summary of content (28 pages)

PAGE 1
JWM90A MOBILE AUDIO SYSTEM Installation and Owner's Manual AUX 1 HDMI USB
PAGE 2
JWM90A Introduction..............................................................................................................................3 Disc Notes................................................................................................................................4 Installation...............................................................................................................................5 Wiring.............................................................................
PAGE 3
JWM90A INTRODUCTION Thank You! Thank you for choosing a Jensen product. We hope you will ﬁnd the instructions in this owner's manual clear and easy to follow. If you take a few minutes to look through it, you'll learn how to use all the features of your new Jensen receiver for maximum enjoyment.
PAGE 4
JWM90A DISC NOTES Depending on the recording status, conditions of the disc, and the equipment used for recording, some CD-Rs/CD-RWs may not play on this unit. For more reliable playback, please adhere to the following recommendations: Ÿ Ÿ Ÿ Use CD-RWs with speed 1x to 4x and write with speed 1x to 2x. Use CD-Rs with speed 1x to 8x and write with speed 1x to 2x. Do not play a CD-RW which has been written more than 5 times.
PAGE 5
JWM90A INSTALLATION . It's a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen JWM90A installed by a reputable RV dealership. NOTE: Before cutting the mounting hole, make sure the area behind the mounting location is clear of wires, fuel and vacuum or brake lines.
PAGE 6
JWM90A WIRING WARNING: Wiring harness comes with stripped and tinned leads to aid in the installation process. Any unused speaker wires must have their exposed ends cut off or insulated individually. The wiring diagram depicts all the wiring connections required for proper operation of the unit. 10 1 20A 20 11 DETAIL A SHOWN FROM PIN VIEW PIN NO.
PAGE 7
JWM90A BASIC OPERATION During RADIO / FRONT AUX / REAR AUX / COAXIAL / OPTICAL / HDMI ARC / HDMI IN mode, press the ▶|| button (18) to mute the audio output for active zones. Press again to restore the previous volume level. 25 34 33 32 31 30 29 28 27 26 23 24 21 During USB / DVD / BT mode, press the ▶|| button to pause playback. Press again to resume playback. 22 Audio Menu Setting 1 20 19 2 18 AUX 1 3 HDMI 4 5 6 USB 7 8 9 10 11 12 14 1.
PAGE 8
JWM90A Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ Ÿ BLUETOOTH DEVICE (Lock/Unlock, Disconnect/Connect, Delete): View, lock and delete from a list of previously paired mobile phone device models. BLUETOOTH (ON/OFF): Choose “Bluetooth On” or Bluetooth Off”. BEEP (ON/OFF): Turn the audible beep On/Off (heard when functions/buttons are selected). Note: Beep tone off will not affect the audible tone of the alarm clock. REGION (USA/EUROPE): Set frequency spacing for various regions. PRESET VOL (1-40): Select an automatic turn on volume.
PAGE 9
JWM90A NOTE: USB will not support Apple device playback. The USB input supplies up to 1A of charging current. Liquid Crystal Display (LCD) The current activated functions and time are shown on the LCD panel (8). Dimming control Ÿ Ÿ Ÿ Ÿ 1. Press the DIM button (6) on the front panel to turn the dimmer On (selected brightness level) and press again to turn the dimmer Off (maximum brightness level). 2. Press & Hold the DIM button (6) to access DIMMER LEVEL menu. 3.
PAGE 10
JWM90A No Device Status Head Unit 1 User Operation Power ON (HDMI Power ON ARC) Remarks Operation Results Head Unit TV TV Power OFF TV Power OFF Power OFF Power ON TV Power OFF Power ON 2 Power OFF 3 Power OFF(Last Power OFF mode is HDMI ARC before Power OFF) Power ON Head Unit Power ON (HDMI ARC) Power ON (Last mode before power off) 4 Power OFF(Last TV, AV, USB, mode is HDMI ARC HDMI(non HDMI before Power OFF) ARC) Power ON Head Unit Audio Out No Audio Out 5 Power ON(HDMI ARC)
PAGE 11
JWM90A Multi-source Mode Setup 1.Press the ZONES button (31) to enter the zone menu. 2.While in the zone menu, press ZONES button (34), or the |<< or >>| buttons (20, 19) repeatedly to navigate through the zones menu settings (ZONE A mode, ZONE A volume adjustment, ZONE B mode, ZONE B volume adjustment, ZONE C mode and ZONE C volume adjustment). 3.Rotate the VOL/ENTER knob to cycle through the available modes.
PAGE 12
JWM90A TUNER OPERATION Recall preset stations 25 34 33 32 31 30 29 28 27 26 23 24 1.Press the PRESETS button (9) to access the preset menu. 2.Press I<< or >>I buttons (19, 20) or rotate the VOL/ENTER knob to navigate the 12 and 18 preset stations for AM or FM respectively. 3.Press the ENTER knob to conﬁrm the selection. 4.Press the BACK button (2) to exit preset menu 21 22 The LCD will display the current station on 1st line and the preset station selection on the 2nd line in presets menu.
PAGE 13
JWM90A DISC OPERATION Track Select 25 34 33 32 31 30 29 28 27 26 23 24 Press the >>| or |<< button (19, 20) to advance to the previous or next track on the CD. The selected track number will appear on the display. Press and hold the >>| or |<< button for more than three seconds to fast forward or fast reverse through the disc. CD play starts when the play/pause button is pressed.
PAGE 14
JWM90A Remote Control Direct Track Entry To select a track directly, use the number pad on the remote control (10). For single digit entries, press the corresponding number for two digit entries. Press the 10+ button followed by the last digit (i.e., for track 16, press 10+ and then 6). Stop Playback Press the ■ button (15) to suspend disc play, and “PRE STOP” will appear in the display. Press the u II button (18) to resume disc play from the last position.
PAGE 15
JWM90A 2. Use the ◄►or ▲▼cursor buttons (15) on the remote control to access the ﬁelds on the "PROG" screen. 3. Use the number buttons on the remote control to enter a track number in each ﬁeld. 4. Press the u /|| button (17) on the remote control or highlight “PLAY” on screen and then press the ENTER button (5) to begin playback in the numbered order indicated to delete the list, highlight “CLEAR” .
PAGE 16
JWM90A MP3/USB OPERATION Ÿ Ÿ ID3 Tag version 1.0: 32 ID3 Tag version 2.x: 32 Mp3 Monitor Display 25 34 33 32 31 30 29 28 27 26 23 24 After loading an MP3 disc or USB device, the following screen will appear on your output monitor 21 22 1 20 19 2 18 AUX 1 3 HDMI 4 5 6 USB 7 8 9 10 Inserting a USB Device The USB connector (11) is at the bottom right corner of the panel. Insert a USB device and press the USB button to select USB mode.
PAGE 17
JWM90A Repeat (RPT) GOTO Direct Track/Chapter Access Press the RPT button (14) on the control panel or the RPT button (20) on the remote control multiple times during playback to select from the following repeat play options: RPT 1 (track),RPT DIR (folder), RPT ALL (disc), OFF. Use the GOTO function to access a track (chapter) directly. 1.Press the GOTO button (25) on the remote control. The On Screen Display information will appear with the track number highlighted. 2.
PAGE 18
JWM90A BLUETOOTH OPERATION Ÿ The JWM90A includes built-in Bluetooth technology that allows you to connect this head unit to Bluetooth devices for streaming audio playback. Ÿ About Bluetooth Technology Bluetooth wireless technology is a short-range wireless radio protocol. Operating in the 2.4 GHz range, it transmits audio and data at speeds up to 2.1 Mbit/s over a range of up to 10 meters. Ÿ Bluetooth On/OFF Ÿ Bluetooth mode is turned ON by default.
PAGE 19
JWM90A APP OPERATION Selecting Tracks During playback, press the >>| or |<< button (19, 20) to play the previous or next track. Pausing Playback During playback, press the ▶ II button (18) to pause the Bluetooth audio playback. “BT PAUSE” will appear on the LCD. Press ▶II button again to resume playback. If you change to another mode, the mobile device audio will pause. Press the BT button (23) to return to Bluetooth mode and resume mobile phone audio playback.
PAGE 20
JWM90A REMOTE CONTROL OPERATION REF DESCRIPTION TUNER 6 BLUETOOTH CD/MP3/USB DVD Turn radio on/standby mode. Turn radio on/standby mode. Turn radio on/standby mode. Turn radio on/standby mode. 1 Adjust volume up/down. Press for Audio Control Setup menu. Adjust volume up/down. Press for Audio Control Setup menu. Adjust volume up/down. Press for Audio Control Setup menu. Adjust volume up/down. Press for Audio Control Setup menu.
PAGE 21
JWM90A 19 Press to view title menu. Use directional arrows and play button to play selected title. May not be supported by all discs. TITLE 20 RPT 21 SOURCE 22 ZOOM 23 ANGLE Select source for playback Select source for playback Repeat track Repeat chapter Select source for playback Select source for playback Zoom picture or press repeatedly to change magniﬁcation level. Select alternate viewing angle, if available. Access Audio Menu options. Access Audio Menu options.
PAGE 22
JWM90A DVD SETUP MENU Press the (setup) button (10) on the remote control to access the SETUP menu and adjust system settings for the following categories: System Setup Language Setup Audio Setup Video Setup Digital Setup Lanuage Setup The Language Setup menu controls the following features: While in the setup menus, use your directional arrows to select and change settings.
PAGE 23
JWM90A Video Setup The Video Setup menu controls the following features: – – – – – Brightness Contrast Hue Saturation Sharpness Digital Setup The Speaker Setup menu controls the following features: – – – OP Mode: Select LINE OUT or RF REMOD. Dynamic Range: Select FULL, 6/8, 4/8, 2/8 or OFF. Dual Mono: Select STEREO, MONO/L, MONO/R or MIX MONO.
PAGE 24
JWM90A CARE AND MAINTENANCE – – – – – Keep the product dry. If it does get wet, wipe it dry immediately. Liquids might contain minerals that can corrode the electronic circuits. Keep the product away from dust and dirt, which can cause premature wear of parts. Handle the product gently and carefully. Dropping it can damage circuit boards and cases, and can cause the product to work improperly. Wipe the product with a dampened cloth occasionally to keep it looking new.
PAGE 25
JWM90A SPECIFICATIONS FCC Notes FM Tuner Frequency Coverage (USA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87.5 to 107.9 MHz Frequency Coverage (Europe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5 to 108 MHz Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <4 μV Stereo Separation@1 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 26
PAGE 27
USB : Press to change the source to USB mode. AUX: Press to cycle through FRONT AUX. REAR AUX, COAXIAL, OPTICAL, HDMI ARC and HDMI IN mode. Press ENTER KNOB to select. Radio will auto-select after MULTI -SO URCE ZO NES: If Zone A is in AM, FM, BT, FRONT AUX or REAR AUX mode, the multi-source function cannot be activated. Zone Band Zone C source mode will follow Zone A.
PAGE 28
Press ~ button to go back to PREVIOUS TRACK or CHAPTER/TITLE. Press and Hold to FAST FORWARD or REVERSE playback. Press & Hold additional times to step through x2, x4, xB, x20. Press PLAY ( ~II ) to resume. DISC : Press to change to the disc mode . ~II : Press to PLAY or PAUSE current audio or video. play each track for 10 seconds in sequential order, and again to toggle off and play current track. ( Not applicable for DVD ) play all tracks in random order . Press again for normal playback .