Dimension Guide

ManualsBrandsJennAir ManualsSingle Wall OvensJennAir NOIR 30" Stainless Steel Single Electric Wall Oven

JEN NAIR

DETAILED PLANN ING D IM EN SION S

2 o f 2

IMPORTANT: Dimensional speciﬁcations are provided for planning purposes only.

Do no t make any cuto uts base d o n this info rmatio n. Refer to the Installation or Use & Care Guide

B EFORE selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.

All JennAir

appliances are appropriately UL, CUL or CSA approved.

®/ ™ © 20 18 Jen n Air. All rig ht s reserved . JEN 25280 -0 0 6.

SINGLE W ALL OVEN S

JJW2427I – 27" x 29-7/8 " x 25 -5/16"

JJW2430I, JJW3430I – 30" x 29-7 /8" x 25-5/1 6"

ELECTRICAL REQUIREM EN TS

If codes permit and a separate ground w ire is used, it is recommended

that a qualiﬁ ed electrical installer determine that the ground path and

the w ire gauge are in accordance w ith local codes.

Check w ith a qualiﬁ ed electrical installer if you are not sure the oven

is properly grounded.

This oven must be connect ed to a grounded metal, permanent

wiring system.

Be sure that the electrical connection and w ire size are adequate and

in conformance w ith the National Electrical Code, ANSI/NFPA 70-latest

edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1

and C22.2 No. O-M 91-latest edition, and all local codes

and ordinances.

A copy of the above code st andards can be obt ained from:

National Fire Protect ion Association

1 Batterymarch Park

Quincy, M A 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

ELECTRICAL CONNECTION

To properly install your oven, you must determine the type of electrical

connection you w ill be using and follow the instructions provided for

it here.

• Oven must be connected to the proper electrical voltage and

frequency as speciﬁed on the model/serial/rating plate. The

model/serial/rating plate is located under the cont rol panel on

single ovens. See the follow ing illustration

A. M odel/Serial/Rating Plate

• M odels rated from 7.3 to 9.6 kW at 240 V (5.4 to 7.4 kW at 208

V) require a separate 40 A circuit. M odels rated at 4.8 kW and

below at 240 V (3.6 kW and below at 208 V) require a separate

20 A circuit .

• A circuit breaker is recommended.

• Connect directly to the circuit breaker box (or fused disconnect)

through ﬂ exible, armored, or nonmetallic sheathed, copper cable

(with grounding w ire).

• Flexible conduit from the oven should be connected directly to

the junction box.

• Fuse both sides of the line.

• Do not cut the conduit. The length of conduit provided

is for serviceability of the oven.

• A UL listed or CSA approved conduit connector

must be provided.

• If the house has aluminum wiring, follow the procedure below :

Connect the aluminum w iring using special connectors and/or

tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer’s recommended

procedure. Alum inum/copper connection must conform w ith

local codes and industry accept ed wiring practices.

For power requirements for models JJW2427I, JJW2430I and

JJW3430I, refer to the following t able.

240 VAC 208 VAC

▼

OD E L K

❦

JJW2427I

4.1 3.1

JJW2430I

4.1 3.1

JJW3430I

4.5 3.4