Installation Instruction

18
To Convert Surface Burners from Natural Gas to
Propane
1. If the burner grates are installed, remove them.
2. Remove burner cap.
3. Remove the burner base by rst removing (2) T-20 screws.
A
C
B
Burner
A. Burner cap
B. Screws
C. Burner base
4. Apply masking tape to the end of a 1/4" (7 mm) nut driver
to help hold the gas orice spud in the nut driver while
changing it. Insert nut driver into the gas opening and press
down onto the gas orice spud and remove by turning the
gas orice spud counterclockwise and lifting out. Set gas
orice spud aside.
5. Replace with correct Propane gas orice spud. See the
“Propane Gas Orice Spud/Hood Chart”.
Use the following chart to nd the exact orice spud
placement.
Propane Gas Orice Spud/Hood Chart
Burner
Rating
Stamp Size Burner Style
7,400 BTUs 70
44
0.70 mm
0.44 mm
Small burner - main
Small burner - simmer
13,000 BTUs 99
50
0.99 mm
0.50 mm
Large burner – main
Larger burner – simmer
16,000 BTUs 116 1.16 mm Grill burner
NOTE: Refer to serial tag for more information on burner ratings
and locations.
Burner orice spud
6. Place Natural gas orice in plastic parts bag for future use
and keep with package containing literature.
NOTE: There may be extra orices in your kit.
7. Replace the burner base and screws. Tighten screws only
until burner is snug to cooktop, do not over-tighten.
8. Replace burner cap.
9. Repeat steps 2 through 8 for the remaining burners.
Adjusting Simmer Low and Main Setting on Surface
Burner for Propane
1. Remove the surface burner control knobs and bezels (oven
control knobs and griddle control knobs do not have to be
removed).
2. Locate the Simmer low-turndown adjustment screw through
the bezel on the left side of the ignition switch.
3. With the burner ON, and set to Simmer Lo, adjust the
simmer ame down to the proper BTU level. Using a
1/8" x 4
1
/
4
" (3.2 mm x 10.8 cm) at blade screwdriver, turn
the simmer low-turndown adjustment screw clockwise until
the ame height is below the bottom of the cap. If the ame
becomes unstable and ickers or appears to race around the
burner, the adjustment is too low and the screw should be
adjusted counterclockwise until the ame is stable. Repeat
this step for all surface burners, except the grill burner.
NOTE: Use a knob to adjust the burner valve.
NOTE: If your range has the IR grill, then skip ahead to the
Convert IR Grill Burner section.
NOTE: Adjust each burner individually.
4. With burner OFF, using the same at blade screwdriver, turn
the main low-turndown adjustment screw 120-135 degrees
clockwise. This will set the main low burner rate to a proper
level.
5. Replace the bezels using the 2 screws which attach to the
valve brackets.
6. Push the surface knobs onto the valve stems.
7. Replace burner grates.
To Convert IR Grill Burner for Propane
1. Unplug range or disconnect power.
2. Remove grill knob and bezel. The other surface knobs and
bezels should still be off the range.
3. Open the oven door and remove the two screws on each
side of the range that hold the control console in place.
NOTE: Make sure to leave oven door open or the control
console will not rest in the side brackets properly once it is
detached.
A
B
A. Size stamp
B. Fuel type stamp (L or N)
A B C
A. Simmer low-turndown adjustment screw
B. Ignition switch
C. Main low-turndown adjustment screw (inside stem)