User Guide

7
Standard Installation - Flush Grille
To remove the top grille panel:
1. Open the door(s).
2. Lift the top grille panel straight up, and then pull straight out.
Place the panel on a soft surface.
To replace the top grille panel:
1. Hook the panel brackets onto the mounting bolts extending
from the top of the refrigerator.
2. Pull the grille panel down slightly to lock into place.
Integrated Installation - Full Height Grille
To install the grille panel to the refrigerator:
1. Slide the upper and lower slots in each bracket onto
the mounting pins extending upward from the top of the
refrigerator.
2. Push the grille panel forward to fully engage the spring clips
and fasten the grille panel
To remove the grille panel from the refrigerator:
1. Open the door(s).
2. Place both hands under the grille panel, grasping the bottom
edge between your ngers and thumbs.
3. Pull the grille panel straight out until the grille stops. Then, lift
up on the grille panel to remove.
Turn Power On or Off:
1. Remove top grille.
2. Press Power switch to the ON or OFF position.
3. Replace top grille.
IMPORTANT: Be sure the power switch is set to the ON position
after cleaning refrigerator or changing light bulbs.
Using the Controls
IMPORTANT:
■ The refrigerator control adjusts the temperature in the
refrigerator compartment. The Freezer control adjusts the
temperature in the freezer compartment.
■ Wait 24 hours after you turn on the refrigerator before you put
food into it. If you add food before the refrigerator has cooled
completely, your food may spoil.
NOTE: Adjusting the temperature controls to a lower (colder)
setting will not cool the compartments any faster.
■ If the temperature is too warm or too cold in the refrigerator
or freezer, rst check the air vents to be sure they are not
blocked before adjusting the controls.
■ The recommended settings should be correct for normal
household usage. The controls are set correctly when milk or
juice is as cold as you like and when ice cream is rm.
■ The actual temperature may differ from the display when a
door is open for an extended period of time.
NOTE: The factory recommended set points are 0°F (-18°C) for
the freezer and 37°F (3°C) for the refrigerator.
Turning Refrigerator On and Viewing Set Points
■ Press the Cooling (ON/OFF) touch pad.
NOTE:
■ After the refrigerator is turned on, the Over Temperature audio
alarm and indicator light may activate every 1½ hours until the
refrigerator and freezer temperatures are below 48°F (9°C) and
15°F (-9°C), respectively, or until the alarm is turned off. To
turn off the audio alarm and indicator light, see “Master Alarm
Reset.”
■ The Cooling ON/OFF touch pad on the control panel shuts
down refrigerator functions such as cooling, lighting, fans and
compressors. To turn the power off completely, use the power
ON/OFF switch located behind the top grille. See “Power On/
Off Switch.”
Viewing the Celsius Temperatures
■ Press the F/C touch pad. To redisplay degrees Fahrenheit,
press F/C again.
NOTE: If the freezer temperature is below zero, the negative sign
next to the freezer display will light up. This is normal.
Adjusting Controls
NOTE: Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
To Adjust Set Point Temperatures:
■ Press the refrigerator or freezer PLUS (+) or MINUS (-) touch
pad until the desired temperature is reached.
■ Press the Set To Recommended touch pad to reset the set
points to the factory recommended temperatures.
NOTE: The set point range for the freezer is -5°F to 3°F
(-21°C to -16°C). The set point range for the refrigerator is
34°F to 42°F (1°C to 6°C).
A
A. Power switch