Owner's Manual

10
CUTOUT DIMENSIONS (H)
Oven Size Oven Cutout Dimension
24" (61 cm) 22
1
/
2
" (57.2 cm)
27" (68.6 cm) 25
1
/
2
" (64.8 cm)
30" (76.2 cm) 28
1
/
2
" (72.4 cm)
36" (91.4 cm) 34
1
/
2
" (87.6 cm)
For the approved model number combinations, refer to the
undercounter label located on top of the oven chassis and on
the bottom of the cooktop burner box.
NOTE: For undercounter installation, it is recommended that the
junction boxes for oven and cooktop be located in the adjacent
right or left cabinet. A 1" (2.5 cm) minimum diameter hole should
have been drilled in the upper rear right or left corner of the side
wall surface to pass the appliance cable through to the junction
box.
Approved Built-In Oven and Induction Cooktop Combinations
A. 24" (61 cm) cabinet depth
B. 25" (63.5 cm) countertop
depth
C. Recommended oven and
cooktop junction box
locations
D. Allow 5/8" (1.6 cm) for oven
trim to overlap on each side.
E. 27
3
/
4
" (70.5 cm) minimum
cutout height
F. 36" (91.4 cm) from cabinet
base to countertop
G. 4
5
/
8
" (11.7 cm) maximum from
cabinet base. If dimension “F”
is greater than 36" (91.4 cm),
dimension “G” can be
increased the same
difference for induction
combinations.
H. See Cutout Dimensions chart.
I. 31
3
/
8
" (82.2 cm) from top of
countertop to bottom of cutout
CUTOUT DIMENSIONS (H)
Oven Size Minimum Oven Cutout
Dimension
24" (61 cm) 22
1
/
2
" (57.2 cm)
27" (68.6 cm) 25
1
/
2
" (64.8 cm)
30" (76.2 cm) 28
1
/
2
" (72.4 cm)
For the approved model number combinations, refer to the
undercounter label located on top of the oven chassis and on
the bottom of the cooktop burner box.
NOTE: For undercounter installation, it is recommended that the
junction boxes for oven and cooktop be located in the adjacent
right or left cabinet. A 1" (2.5 cm) minimum diameter hole should
have been drilled in the upper rear right or left corner of the side
wall surface to pass the appliance cable through to the junction
box.
Approved Built-In Oven and Gas Cooktop Combinations
A. 24" (61 cm) cabinet depth
B. 1" (2.5 cm) clearance to
bottom of countertop
C. 25" (63.5 cm) countertop
depth
D. Recommended oven junction
box locations.
E. 1" (2.5 cm) clearance to
cabinet
F. 27
3
/
4
" (70.5 cm) minimum
cutout height
G. Allow 5/8" (1.6 cm) for oven
trim to overlap on each side.
H. 36" (91.4 cm) from cabinet
base to countertop
I. 31
3
/
8
" (79.7 cm) from top of
countertop to bottom of cutout
J. Gas line through wall 10
1
/
2
"
(26.7 cm) to center of cutout
K. 3
1
/
4
" (8.3 cm)
L. Gas line through floor 10
1
/
2
"
(26.7 cm) to center of cutout
M. 3
1
/
2
" (8.9 cm)
N. 4
5
/
8
" (11.7 cm) maximum from
cabinet base
O. See Cutout Dimensions chart.
CUTOUT DIMENSIONS (O)
Oven Size Minimum Oven Cutout
Dimension
24" (61 cm) 22
1
/
2
" (57.2 cm)
27" (68.6 cm) 25
1
/
2
" (64.8 cm)
30" (76.2 cm) 28
1
/
2
" (72.4 cm)
36" (91.4 cm) 34
1
/
2
" (87.6 cm)
For the approved model number combinations, refer to the
undercounter label located on top of the oven chassis.
NOTE: For undercounter installation, it is recommended that the
junction box for oven be located in the adjacent right or left
cabinet. A 1" (2.5 cm) minimum diameter hole should have been
drilled in the upper rear right or left corner of the side wall surface
to pass the appliance cable through to the junction box.
The upper shaded areas are recommended locations for recessed
junction box for 120 V grounded outlet for cooktop.
Lower shaded areas are recommended locations for flexible or
rigid gas pipe installation. The gas connection on the cooktop is
on the right (same location as “J” in the above diagram). The gas
pipe can be installed on either side of the cutout, and either
through the floor or through the wall. Refer to local codes
regarding the use of gas lines.