Installation guide
3.
Depending
on
your
model
and
the
compartment,
rotate
the
plastic
spacer
so
that
the
curved handle
mounting
posts
are
either
at
the
top,
bottom
or to
the
left.
See
following
chart.
Bottom
Mount
French
Door
Both
Bottom
Mount
Models
Refrigerator
Refrigerator
Freezer
Left
Right
Left
Right
Swing
|
Swing
Door
Door
|
Drawer
Curved
Bottom
Top
Bottom
Top
Left
Mounting
Post
Setscrews
Right
Left
Right
Left
Down
4.
Slide
the
screw
into
the
handle
mounting
stud.
Insert
the
screw
assembly
into
the
center
hole
of
the
plastic
spacer
and
fasten
it
to
the
door
panel.
5.
Install
the
handles
to
the
handle
mounting
studs
so
that
the
setscrews
are
on
the
designated
side
and
tighten
the
setscrews.
Hn
Led
B
i
isiall
Base
Grille
aor
se
RE
x
se
ce
i
There
are
two
pieces
to
t
base
grille itself
and
the
skirt.
The
skirt
can
be
added
to
the
base
grille
in
order
to
extend
it
all
the
way
to
the
floor.
1.
To
see
whether
the
skirt
is
needed,
place
the
base
grille
into
position.
Do
not
attach
the
base
grille
to
the
refrigerator.
Measure
the
distance
between
the
bottom
of
the
base
grille
and
the
floor.
The gap
must
be
a
minimum
of
¥%"
(1.27
cm)
in
order
to
add
the
skirt.
NOTE:
If
the
gap
measures
less
than
%"
(1.27
cm), skip
steps
3
and
4
of
the
instructions,
and
install
the
base
grille
only.
2.
Remove
the
film
from
the
base
grille.
3.
Snap
the
skirt
onto
the
base
grille.
A.
Base
grille
B.
Skirt
base
grille
to
allow
for
a
custom
fit:
the
4.
Trim
the
skirt
by
scoring
the
proper
“V”
groove
with
a
utility
knife.
Break
the
skirt
at
the
score
line.
>
sete
A.
“V”
groove
5.
Using
the
two
screws,
attach
the
base
grille
assembly
to
the
refrigerator
as
shown.
NOTE:
Drive
in
the
right
side
screw
first.
A.
Screws
(2)
Complete
installation
Turn
the
water
supply
line
valve
to
the
“Open”
position.
2.
Turn
the
refrigerator
switch
to
the
ON
position.
See
“Power
On/Off
Switch”
in
the
Use
&
Care
Guide
for
instructions.
Wait
a
few
minutes.
Check
the
water
line
connections
for
leaks.
3.
Remove
all
boxes,
parts
packages
and
packing
materials
from
the
interior
of
the
refrigerator.
See
the
“Cleaning”
section
in
the
Use
&
Care
Guide
for
instructions.
Remove
the
film
and
cardboard
from
the
grille
and
doors
or
door
frame,
depending
on
your
model.
4.
Install
the
shelves
and
bins
in
the
refrigerator
and
freezer
compartments.
5.
The
controls
are
preset
at
the
factory
to
the
midpoint
setting.
Check
that
the
compressor
is
operating
properly
and
that
all
the
lights are
working.
6.
Flush
the
water
system
before
use.
See
“Water
System
Preparation.”
To
get
the
most
efficient
use
from your
new
built-in
refrigerator,
read
the
Use
&
Care Guide.
Keep
Installation
Instructions
and
Use
&
Care
Guide
near
the
built-in
refrigerator
for
easy
reference.
27