Installation guide
Standard
Installation
-
Flush
Grille
-
Open
or
Closed
Soffit
v
|
A
D
>|
|
DLS
gms,
gp
be
:
Move
The
R
peg
%
AWARNING
”
teal?
&
efrigerator
info
House
¢
2
1"
(2.54
om)
|
Top
Grille
Filler
~<
E
>|
54"
B
(14.55
cm) Top
Grille
Panel
.
v
Model
36 42
Reveal
x"
Ye"
x"
Ye"
D
354"
3544"
Aq
Va"
Aya"
(89.54
cm)
(90.81
cm)
|
(104.76
cm)
|
(106.05
cm)
E
35%
3544"
Aq
Va"
Aya"
(89.54
cm)
(90.81
cm)
|
(104.76
cm)
|
(106.05
cm)
IMPORTANT:
The
grille
panel
height,
shown
in
the
Standard
Installation
Flush
Grille
graphic,
allows
for
an
air
gap
critical
to
refrigerator
performance.
INSTALLATION
INSTRUCTIONS
Tip
Over
Hazard
Refrigerator
is
top
heavy
and
tips
easily
when
not
completely
installed.
Keep
doors
taped
closed
until
refrigerator
is
completely
installed.
Use
two
or
more
people
to
move
and
install
refrigerator.
Failure
to
do
so
can
result
in
death
or
serious
injury.
Tip
Over
Hazard
Refrigerator
is
top
heavy
and
tips
easily
when
not
completely
installed.
Keep
doors
taped
closed
until
refrigerator
is
completely
installed.
Use
two
or
more
people
to
move
and
install
refrigerator.
Failure
to
do
so
can
result
in
death
or
serious
injury.
IMPORTANT:
m
Do
not
remove
the
film
covering
until
the
refrigerator
is
in
its
operating
location.
gm
All
four
leveling
legs
must
contact
the
floor
to
support
and
stabilize
the
full
weight
of
the
refrigerator.
m
Keep
the
cardboard
shipping
piece
or
plywood
under
the
refrigerator
until
it
is
installed
in
the
operating
location.
1.
Remove
and
save
the
literature
package
and
hardware
kit
located
inside
the
refrigerator.
Remove
and
save
the
literature,
grille,
and
trim
taped
to
the
outside
of
the
refrigerator.
NOTE:
Do
not
remove
tape
and
door
bracing
until
the
refrigerator
is
in
its
final
location.
1.
Place
an
appliance
dolly
under
the
left
side
of
the
refrigerator
as
shown.
Place
the
corner
posts
from
the
packing
materials
over
the
trims
as
appropriate.
Slowly
tighten
the
strap.
2.
Place
pieces
of
the
shipping
carton
on
the
floor
when
rolling
the dolly
and
refrigerator
into
the
house.
Move
the
refrigerator
close
to
the
built-in
opening.
3.
Place
top
of
cardboard
carton
or
plywood
under
refrigerator.
4.
Stand
the
refrigerator
up.
First,
place
the
left
bottom
edge
of
the
refrigerator
on
the
floor,
stand
the
refrigerator
upright
and
then
lower
the
right-hand
side
of
the
refrigerator
to
the
floor.
IMPORTANT:
a
If
asolid
soffit
is
not
available,
an
anti-tip
board
must
be
installed.
gm
It
is
recommended
that
board(s)
be
installed
before
the
refrigerator
is
installed.
m
Board(s)
must
be
long
enough
to
fully
cover
the
width
of
the
compressor
cover.
m
Locate
the
board(s)
so
the
bottom
surface(s)
of
the
board(s)
is(are)
84"
(213
cm)
from
the
floor.
m
During
installation,
raise
the
refrigerator
up
until
the
top
of
the
refrigerator
is
making
contact
with
the
bottom
of
the
anti-tip
board(s).
Do
not
crush
the
compressor
cover
when
raising
the
rear
leveling
legs.
17