Use and Care Manual
4
CARE & MAINTENANCE
Interior & Exterior Doors (JCM005)
DOORSURFACECLEANING&HARDWARELUBRICATION
LABEL REMOVAL
Slowly peel from one corner. If label tears or sticks, moisten with 
soapy water and gently scrape with plastic putty knife. Stubborn 
labels can be soaked with soapy water and covered overnight with 
plastic wrap. Gently remove with plastic putty knife.
STUBBORN STAIN REMOVAL
Commercial glass cleaning products may be necessary.
• Applysmallamountdirectlytothestain.Avoidspillingor
dripping down the glass.
• Somepersistentstainsmayneedhigherstrengthcleaning
solutions that contain active ingredient chemicals such as 
denatured alcohol or acetone. Special care must be taken when 
using these types of cleaners.
• Foroilandgrease:trybakingsodaandwater.
 MORE INFORMATION ON GLASS CLEANING
• TheGlassAssociationofNorthAmerica(GANA): 
www.glasswebsite.com
Note on Web sites! Web site content is subject to change and 
should be used for informational purposes only. JELD-WEN is not 
responsible for third-party information.
Clean door surface and maintain hardware any time doors are not 
openingorclosingproperlyoratleastbiannually(monthlyfor
coastalareas):
• Cleandirt/debriswithmildsoapandwaterandrinseclean
• Tightenloosescrews
• Replacedamagedhardware
PRECAUTIONS
The following substances may damage protective nishes. Do not use:
• Vinegar-basedcleaners(useonglassonly)
• Citrus-basedcleaners(lemon,etc.)
• Paintremovers
• Windowcleaners
• Brick/sidingwashes
• Anyotherindustrialorabrasivecleaners
1. Lubricatehingeswithlightoil(3-In-
One
®
oilorequivalent)annuallyor
when noisy.
2.  Spray keyway lock with graphite 
lubricant.
FOLDING DOORS:
Tracks and Bearings
Wipevisibletracksurfaceswithadampsoftclothandamild
detergent, then wipe dry with a clean cloth. Using a suitable 
applicatorspreadasmallamountofclearpetroleumjellyorsimilar
lubricant where the carrier wheels pass so that it is distributed evenly 
along the track. Place additional lubricant around the bearings. The 
lubrication reduces wear, improves operation and protects against 
corrosion.Insevereenvironments,applyathinlmofWD40
®
.
Hangers, Pivots and Brackets
Exposed surfaces should be wiped down with warm soapy water 
and a soft rag, and then rinsed clean before applying new surface 
protectant.AlightsprayapplicationofWD40
®
, followed by a light 
wipe with a dry cloth to remove any excess.
Hinges
Wipedownthevisiblesurfaceswithwarm,soapywaterandasoft
rag, then rinse off and dry by wiping with a clean rag. Application 
ofathinlmofWD40
®
 will help maintain the original luster of the 
metal nish, and lubricate the moving contact surfaces. Be careful 
not to get these compounds on any wood components as it may 
cause staining. For oil-rubbed bronze nish, care should be taken 
when cleaning or re-applying surface protectant.
Flushbolts
SprayWD40
®
 to the sliding pin inside the bolt and to the lock 
cylinder. There are access holes or slots on all drop bolts so that this 
can be completed without removing the locks from the doors.
Cleaning and lubrication help to maintain and restore smooth operation to movable parts such as hinges and locksets and, in most cases, 
offers some corrosion protection.
CLEANING GLASS
GENERAL CLEANING
Preparecleaningsolution(1tsp.babyshampootoonegallonof
wateror11/2cupsvinegartoonegallonofwater).
1. Rinsesurfacewithcleanwaterfromtoptobottom.
2.  Clean with mild soap and water and sponge or soft brush with 
uniform pressure horizontally, then vertically.
3. Promptlyrinsethoroughlywithcleanwater(spongingwhile
rinsingmaybehelpful;donotallowcleaningsolutiontodryon
thesurfaceorcollectandpuddle).
4. Wipedrywithlint-freedrycloth.
5.  If necessary, repeat steps above until clean.
6.  Dry door with separate cloth.
PAINT REMOVAL
1. Soak dried latex paint drips with warm water and baby shampoo 
solution. For oil-based paint, consult a paint professional.
2. Wipewithdampclothorsponge.
If needed,
3. Scrapegentlywithplasticputtyknife.Repeatsoakandscrape.
4.  Repeat if necessary.






