Instructions / Assembly

4
MATERIALS AND TOOLS
INSPECT PRODUCT
1
Installation Instructions
for Vinyl Windows without Nailing Fin (JII011)
JELD-WEN exterior window and door products should be installed
in accordance with JELD-WEN’s recommended installation
instructions, which are printed on the product label or can be found
on our website: www.jeld-wen.com.
NOTE: Alternative installation methods and ashing systems
may be utilized at the installer’s or owner’s discretion and, in
such situations, the installation should be done in accordance
with the ashing manufacturer’s instructions. Follow all material
manufacturers’ instructions for proper use and compatibility. When
using ashing, spray adhesive/primer, sealant and foam products,
we recommend using the same manufacturer and verifying
compatibility. It is the End User’s responsibility to determine
if dissimilar materials are compatible with the substrates in
theapplication.
Needed Materials
• #8 pan-head or washer-head, corrosion-resistant screw. Minimum
embedment of 1 1/4" into the structural framing (or as required by
localcode).
• For securing the sill in masonry applications, 3/16" self-tapping concrete
screws (gasket-head optional or as required by local code). Minimum
embedment of 1 1/4" into the structural framing (or as required by
code). Apply sealant to the self-tapping concrete screw threads and
head of the screw.
• For Wind Zone 3 (WZ3) Products (Tilt Single Hung, Side Load Single
Hung, Tilt Double Hung and Horizontal Slider Windows): #8 x 2 1/2"
at head screws (stainless steel recommended) are needed to go
through and anchor the bracket to the rough framing (two screws
per bracket).
• Sill Pan Material: Ridged sill pan, self-adhered ashing (SAF), liquid
applied ashing or a combination of the materials listed.
• Sealant: We recommend OSI
®
QUAD
®
Max Sealant or equivalent (for
interior air seal). This sealant can be used in any application and can be
painted or ordered in a color matched product if desired.
• Polyurethane low expansion Window and Door foam: We recommend
OSI
®
QUAD
®
Foam or equivalent (for interior air seal).
• Backer rod: 1/8" larger than the widest portion of the gap (used in
conjunction with sealant bead for interior air seal).
• Non-compressible or non-water degradable shims.
• Drip cap (if not supplied).
Additional Materials Needed if Installing into an Existing
WindowFrame:
• Composite or solid wood (cedar or redwood recommended) or exterior
grade plywood for shimming.
• If installing into an existing aluminum window, dimensions should be
1/2" shorter than the length of the sill track and 1/4" taller than the
depth of the track.
• If installing into an existing wood window, dimensions should be
1/4" thick, length of the existing frame sill minus 1" and the width of
the new vinyl window side jamb minus 1/4".
Potential Needed Tools
• Utility knife/shears
• J-roller
• Hammer
• Tape measure
• Caulking gun
• Level (4' minimum recommended)
• Drill with bits
• Pry bar
• Screwdriver
• Hacksaw
• Putty knife
Remove Packaging
• Remove shipping materials such as corner covers, shipping blocks,
shrink wrap or pads. If there is a protective lm on the glass, do not
remove it until installation and construction are complete.
• Do not remove the installation label until after the inspection of the job
iscomplete.
Inspect Window
• Cosmetic damage.
• Product squareness (diagonal measurements not more than
1/4"different).
• Correct product (size, color, grid pattern, handing, glazing, energy-
efciency requirements, etc.).
• Cracked frame welds or other frame damage.
• For side-by-side mulled units, a drip cap that extends the length of the
frame plus 1/8" overhang on each end is required.
If any of the above conditions represent a concern, or if you expect
environmental conditions to exceed the window’s performance
rating, do not install the window. Contact your dealer or distributor
forrecommendations.