SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 8 䡵 Rollover Warning . . . . . . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Identification Number .............. 8 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 6 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . .
INTRODUCTION INTRODUCTION Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. Before you start to drive this vehicle, read the Owner’s Manual. Be sure you are familiar with all vehicle controls, particularly those used for braking, steering, transmission, and transfer case shifting. Learn how your vehicle handles on different road surfaces.
INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet, located on the DVD, and various customer-oriented documents. Please take the time to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire.
INTRODUCTION 7 1
INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions.
INTRODUCTION 9 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 14 䡵 Vehicle Security Alarm . . . . . . . . . . . . . . . . . . . 19 ▫ Wireless Ignition Node (WIN) . . . . . . . . . . . . 14 ▫ Rearming The System . . . . . . . . . . . . . . . . . . 19 ▫ Integrated Ignition Key . . . . . . . . . . . . . . . . . 15 ▫ To Set The Alarm . . . . . . . . . . . . . . . . . . . . . 19 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Remote Open Window Feature — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 24 ▫ Programming Additional Transmitters . . . . . . 24 ▫ Transmitter Battery Service . . . . . . . . . . . . . . 24 ▫ General Information . . . . . . . . . . . . . . . . . . . 25 䡵 Remote Starting System — If Equipped . . . . . . . 26 ▫ How To Use Remote Start . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Enhanced Seat Belt Use Reminder System 䡵 Engine Break-In Recommendations . . . . . . . (BeltAlert威) . . . . . . . . . . . . . . . . . . . . . . . . . 47 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . ▫ Seat Belts And Pregnant Women . . . . . . . . . . 48 ▫ Transporting Passengers . . . . . . . . . . . . . ▫ Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . 48 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Remote Keyless Entry (RKE) transmitter with integrated ignition key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided key into the ignition switch with either side up. Wireless Ignition Node (WIN) The Wireless Ignition Node (WIN) operates similar to an ignition switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Integrated Ignition Key The integrated ignition key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the RKE transmitter. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead. The emergency key is also for locking the glove box. You can keep the emergency key with you when valet parking.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • If you try to remove the key before you place the shift lever in PARK, it may become trapped temporarily in the ignition switch. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition switch to warn you that this safety feature is inoperable. The engine can be started and stopped, but the key cannot be removed until you obtain service.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 the vehicle. The system will shut the engine off in two Key-In-Ignition Reminder If you open the driver’s door with the integrated ignition seconds if an invalid RKE transmitter is used to start the key in the ignition, a chime will sound to remind you to engine. remove the key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Sentry Key威 Immobilizer system is not compatible with aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN). Keep the PIN in a secure location. This number is required for authorized dealer replacement of RKE transmitters.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 park lamps and/or turn signals will flash for an addiGeneral Information The Sentry Key威 system complies with FCC rules Part 15 tional 15 minutes. and with RSS-210 of Industry Canada. Operation is NOTE: The Panic and Security alarms are quite differsubject to the following conditions: ent. Please take a moment to activate the Panic and the Security modes to hear the differences in the horn. In case • This device may not cause harmful interference.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Vehicle Security Light (located in the instrument cluster) will flash rapidly for about 16 seconds to signal that the Vehicle Security Alarm is arming. During this 16 second arming period, opening any door or the liftgate will cancel the arming. If the Vehicle Security Alarm successfully arms, the Vehicle Security Light will flash at a slower rate to indicate the alarm is set.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 REMOTE KEYLESS ENTRY (RKE) This system allows you to lock or unlock the doors and liftgate, or activate the panic alarm, from distances up to approximately 66 ft (20 m) using a hand-held Remote Keyless Entry (RKE) transmitter. The RKE transmitter does not need to be pointed at the vehicle to activate the system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Key Unlock, Driver Door/All Doors First • For vehicles equipped with the Electronic Vehicle Press Information Center (EVIC), refer to “Flash Lamps with This feature lets you program the system to unlock either Lock,” under “Personal Settings (Customerthe driver’s door or all doors, on the first press of the Programmable Features)” in the ⬙Electronic Vehicle UNLOCK button on the RKE transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock the Doors Press and release the LOCK button on the RKE transmitter to lock all doors. The turn signal lamps will flash and the horn will chirp to acknowledge the signal. Sound Horn with Remote Key Lock This feature will cause the horn to chirp when the doors are locked with the RKE transmitter. This feature can be turned on or off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using the Panic Alarm To turn the Panic Alarm feature on or off, press and hold the PANIC button on the RKE transmitter for at least one second and release. When the Panic Alarm is on, the headlights and park lamps will flash, the horn will pulse on and off, and the interior lights will turn on. Programming Additional Transmitters If you do not have a programmed RKE transmitter, contact your authorized dealer for details.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 3. Reposition the access door panel over the battery opening and snap into place. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. Battery Replacement 1— Battery Access Door 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If your RKE transmitter fails to operate from a normal How to Use Remote Start All of the following conditions must be met before the distance, check for these two conditions: engine will remote start: 1. A weak battery in the RKE transmitter. The expected • Shift lever in PARK life of the battery is a minimum of three years. 2. Closeness to a radio transmitter such as a radio station • tower, airport transmitter, and some mobile or CB radios.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon monoxide is poisonous and can cause serious injury or death when inhaled. • Keep Remote Keyless Entry (RKE) transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: To avoid unintentional shutdowns, the system DOOR LOCKS will disable the one time press of the REMOTE START Manual Door Locks button for two seconds after receiving a valid Remote Use the manual door lock plunger to lock the doors from Start request. inside the vehicle. If the plunger is down when the door To Exit Remote Start Mode and Drive the Vehicle is closed, the door will lock.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 If you press the door lock switch while the keys are in the Power Door Locks The power door lock switch is located on each front door ignition switch and the driver’s door is open, the doors panel. Press the switch to lock or unlock the doors. will not lock. The rear doors cannot be opened from inside the vehicle until you pull up the lock plungers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This feature is selectable and can be turned on or off. Refer to “Auto Door Locks” under “CustomerProgrammable Features” in the “Electronic Vehicle Information Center (EVIC),” in Section 4 of this manual, or see your authorized dealer. Child Protection Door Lock The rear doors of your vehicle are equipped with Child Protection Door Locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 passenger/rear passenger door windows. The window Auto-Down controls will operate only when the ignition switch is in Both the driver and front passenger window switch have an Auto-Down feature. Press the window switch past the the ON or ACC position. first detent, release, and the window will go down automatically. To cancel the Auto-Down movement, operate the switch in either the up or down direction and release the switch.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Up Feature with Anti-Pinch Protection — Driver’s and Front Passenger Door Only Lift the window switch to the second detent, release, and the window will go up automatically. To stop the window from going all the way up during the Auto Up operation, push down on the switch briefly. WARNING! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. Liftgate Release WARNING! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Power Liftgate — If Equipped The power liftgate may be opened manually or by pressing the LIFTGATE button on the ReTo avoid injury, stand back when opening. Glass will mote Keyless Entry (RKE) transmitter. Press automatically rise. the LIFTGATE button on the RKE transmitetr Once the liftgate flipper glass has been opened, connec- twice within five seconds, to open the power liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the liftgate trim panel. WARNING! During power operation, personal injury or cargo damage may occur. Ensure the liftgate travel path is clear. Make sure the liftgate is closed and latched before driving away.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 • The power liftgate must be in the full open position for • The power liftgate will not operate in temperatures rear liftgate close button or overhead console close below ⫺22°F (⫺30°C) or temperatures above 150°F button to operate. If the liftgate is not fully open, press (65°C).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. • If you are required to drive with the liftgate open, make sure that all windows are closed, and the climate control blower switch is set at high speed. DO NOT use the recirculation mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Knee bolsters/blockers for front seat occupants • Front seat belts incorporate pretensioners to enhance occupant protection by managing occupant energy during an impact event If you will be carrying children too small for adult-sized seat belts, the seat belts or the Lower Anchors and Tether for CHildren (LATCH) feature also can be used to hold infant and child restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions in your vehicle have combination lap/shoulder belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A belt that is worn under your arm is very dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries. Ribs are not as strong as shoulder bones. Wear the belt over your shoulder so that your strongest bones will take the force in a collision. • A shoulder belt placed behind will not protect you from injury during a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (i.e., bent retractor, torn webbing, etc.).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Automatic Locking Mode — If Equipped In this mode, the shoulder belt is automatically prelocked. The belt will still retract to remove any slack in the shoulder belt. When to Use the Automatic Locking Mode The Automatic Locking Mode should be used anytime a child safety seat is installed in a second or third row seating position. Children 12 years old and younger should be properly restrained in a rear seat whenever possible.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How to Disengage the Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the Automatic Locking Mode and activate the Vehicle Sensitive (Emergency) Locking mode. Energy Management Feature This vehicle has a safety belt system with an Energy Management feature in the front seating positions to help further reduce the risk of injury in the event of a head-on collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 NOTE: These devices are not a substitute for proper seat BeltAlert威 will be reactivated if the driver’s seat belt is belt placement by the occupant. The seat belt must still be unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). worn snugly and positioned properly. The pretensioners are triggered by the Occupant Restraint Controller (ORC). Like the airbags, the pretensioners are single use items.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Turn the ignition key to the OFF position. A single Seat Belt Extender chime will sound to signify that you have successfully If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if completed the programming. equipped) is in its lowest position, your authorized BeltAlert威 can be reactivated by repeating this procedure. dealer can provide you with a seat belt extender.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Supplemental Restraint Systems (SRS) This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Airbags have a multistage inflator • Steering Wheel and Column design. This allows the airbag to have different rates of • Instrument Panel inflation based on the severity and type of collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 low, medium, or high. If a low output is sufficient to meet Supplemental Side Airbag Inflatable Curtain the need, the remaining gas in the inflator is expended. (SABIC) — If Equipped SABIC airbags offer side-impact and vehicle rollover WARNING! protection to front and rear seat outboard occupants in addition to that provided by the body structure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Airbag covers may not be obvious in the interior trim; but they will open during airbag deployment. The system includes sensors adjacent to both front and rear seat occupants that are calibrated to deploy the SABIC airbags during impacts that require airbag occupant protection.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Along with seat belts and pretensioners, Advanced Front Airbags work with the knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection. 53 WARNING! Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment can cause severe injury or death to infants in that position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You should read the instructions provided with your child restraint to make sure that you are using it properly. All occupants should ALWAYS wear their lap and shoulder belts properly. The driver and front passenger seats should be moved back as far as practical to allow the Advanced Front Airbags room to inflate. Do not lean against the door.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 The Advanced Front Airbags will not deploy in all frontal collisions, including some that may produce substantial Occupant Restraint Controller (ORC) vehicle damage — for example, some pole collisions, The ORC is part of a Federally regulated safety system truck underrides, and angle offset collisions. On the other required for this vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON position. If the key is in the LOCK position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. The ORC contains a backup power supply system that may deploy the airbags even if the battery loses power or it becomes disconnected prior to deployment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the Advanced Front Airbags. Different airbag inflation rates are possible, based on the collision type and severity. The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50 to 70 milliseconds. This is about half of the time it takes to blink your eyes.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front and Side Impact Sensors • Turn on the interior lights, which remain on as long as In front and side impacts, impact sensors aid the ORC in the battery has power or until the ignition key is determining appropriate response to impact events. Adremoved. ditional sensors in the ORC determine the level of airbag • Unlock the doors automatically. deployment and provide verification.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision which deploys the airbags, any or all of the following may occur: 59 throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • The nylon airbag material may sometimes cause abrasions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! (Continued) WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Airbag Warning Light You will want to have the airbags ready to inflate for your protection in a collision. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system immediately. located on the inside of the fuse block cover for the proper airbag fuses. See your authorized dealer if the fuse is good.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Under certain circumstances, EDR data may not be download data by a court with legal jurisdiction (i.e., pursuant to a warrant). A copy of the data will be recorded (e.g., loss of battery power). provided to the custodial entity upon request.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 4. Otherwise required by law. Child Restraints Everyone in your vehicle needs to be buckled up all the Data parameters that are recorded: time, including babies and children. Every state in the • Diagnostic trouble code(s) and warning light status for United States and all Canadian provinces require that electronically-controlled safety systems, including the small children ride in proper restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured. Any child riding in your vehicle should be in a proper restraint for the child’s size. • The infant carrier is only used rearward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. • A rearward-facing infant restraint should only be used in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the latch plate from the buckle, turn the buckle locking retractor, pull the belt from the retractor until around, and insert the latch plate into the buckle there is enough to allow you to pass through the child again. If you still cannot make the child restraint restraint and slide the latch plate into the buckle. Then, secure, try a different seating position. pull the belt until it is fully extracted from the retractor.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg), and who are older than one year.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH — Child Seat Anchorage System (Lower Anchors and Tether for CHildren) Your vehicle’s second row seat is equipped with the child restraint anchorage system called LATCH. The LATCH system provides for the installation of the child restraint without using the vehicle’s seat belts, instead securing the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure. strap kits or retro-fit kits.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If your child seats are not LATCH-compatible, you can only install the child seats using the vehicle’s seat belts. For typical installation instructions, refer to “Installing the LATCH-Compatible Child Restraint System”. 2 Installing the LATCH-Compatible Child Restraint System We urge you to carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next attach the lower hooks or connectors over the top of the anchorage bars, pushing aside the seat cover material.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the buckle, turn the buckle around, and insert the latch For the outboard seating positions, route the tether over plate into the buckle again. If you still can’t make the the head rests, and attach the hook to the tether anchor located on the back of the seat. child restraint secure, try a different seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 A new engine may consume some oil during its first few ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine in thousand miles (kilometers) of operation. This should be your vehicle. considered a normal part of the break-in and not interpreted as an indication of difficulty. Drive moderately during the first 300 miles (500 km).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Periodic Safety Checks You Should Make Outside the Vehicle Lights Have someone observe the operation of exterior lights while you work the controls. Check turn signal and high beam indicator lights on the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 ▫ Illuminated Vanity Mirrors — If Equipped . . . 85 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 82 ▫ Sun Visor Extension — If Equipped . . . . . . . . 85 ▫ Automatic Dimming Mirror — If Equipped . . . 82 䡵 uconnect™ phone — If Equipped . . . . . . . . . . . 85 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Four-Way Passenger’s Power Seat — If Equipped . . . . . . . . . . . . . . . . . . . . . . . 88 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . . 89 ▫ Front Heated Seats — If Equipped . . . . . . . . . 90 ▫ Rear Heated Seats — If Equipped . . . . . . . . . . 91 ▫ 40/20/40 Second Row Folding Seat . . . . . . . . 93 ▫ 50/50 Third Row Folding Seat — If Equipped . . . . . . . . . . . . . . . . . . . . . . . 97 䡵 Driver Memory Seat — If Equipped . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Battery Saver Feature — Exterior/Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 ▫ Lights-On Reminder . . . . . . . . . . . . . . . . . . 110 ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . 110 ▫ Lane Change Assist . . . . . . . . . . . . . . . . . . . . 111 ▫ High/Low Beam Switch . . . . . . . . . . . . . . . . 111 ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . . 111 ▫ Headlight Off Delay . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Rear Park Assist — If Equipped . . . . . . . . . . . 122 ▫ Programming HomeLink威 . . . . . . . . . . . . . . 132 ▫ Rear Park Assist Sensors . . . . . . . . . . . . . . . 122 ▫ Gate Operator/Canadian Programming . . . . 134 ▫ Rear Park Assist Warning Display . . . . . . . . 123 ▫ Using HomeLink威 . . . . . . . . . . . . . . . . . . . 135 ▫ Enable/Disable The Rear Park Assist . . . . . . 124 ▫ Reprogramming A Single HomeLink威 Button . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 ▫ Venting Sunroof — Express . . . . . . . . . . . . . 138 ▫ Front Cupholders . . . . . . . . . . . . . . . . . . . . 145 ▫ Sunshade Operation . . . . . . . . . . . . . . . . . . 139 ▫ Cupholders — Second Row Seat . . . . . . . . . 146 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . 139 ▫ Cupholders — Third Row Seat . . . . . . . . . . . 146 ▫ Sunroof Maintenance . . . . . . . . . . . . . . . . . 139 䡵 Cargo Area Features . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Automatic Dimming Mirror Vehicles and other objects seen in the passenger-side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger-side mirror could cause you to collide with another vehicle or other object.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Automatic Dimming Mirrors — If Equipped The driver and passenger outside mirrors will automatically adjust for glare from vehicles behind you. This feature is controlled by the inside Automatic Dimming Mirror and can be turned on or off by pressing the button at the base of the inside mirror. The mirrors will automatically adjust for headlight glare when the inside mirror adjusts.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Illuminated Vanity Mirrors — If Equipped Sun Visor Extension — If Equipped To access an illuminated vanity mirror, flip down one of This feature has a pull out extension on the sun visor for the sun visors. increased coverage. Lift the cover to reveal the mirror. The light will turn on uconnect™ phone — IF EQUIPPED automatically. Refer to “uconnect™ phone” in the uconnect™ User Manual located on the DVD for further details.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! • DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 WARNING! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked. Manual Lumbar Support Adjustment The manual lumbar support adjustment lever is located on the right side of the driver’s seatback and on the left side of the passenger’s seatback (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Eight–Way Driver’s Power Seat The driver’s power seat switches are located on the outboard side of the driver’s seat. The bottom switch controls up/down, forward/rearward, and tilt adjustment. The top switch controls the seatback recline adjustment. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 NOTE: The four-way seat does not have an up/down The head restraints have a locking button which must be pushed in to lower the head restraint to all positions. The adjustment. restraints may be raised without pushing in the button. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision. The head restraints should always be checked prior to operating the vehicle and never adjusted while the vehicle is in motion. Always adjust the head restraints when the vehicle is in PARK. Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. • Do not place anything on the seat that insulates against heat, such as a blanket or cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE After turning the ignition ON, you can choose from High, Low or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low and none for Off. Press the switch once to select High-level heating. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. To avoid heated seat surfaces coming in contact and potential seat overheating, always ensure that the seat heater is in the Off position before placing any of the seats into a folded flat position (if equipped). 1. Pull up on the seatback lever located on the outboard side of the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Fold the seatback down, and tumble the seat forward. WARNING! Do not drive the vehicle with the outer second row seats in the tumbled position. The outer second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in personal injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Folding Middle Seatback (Second Row Seat) 1. Pull the release strap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Lower the center seatback. Center Seat Armrest (Second Row Seat) — If Equipped The second row center seat may be equipped with a armrest. Pull strap to lower armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 50/50 Third Row Folding Seat — If Equipped To Lower Rear Seat Either side of the third row seat can be lowered to allow for extended cargo space and still maintain some rear seating room. 3 1. Open the tailgate. 2. Pull the seatback release handle (toward rear of vehicle) and lower the seatback using the pull strap. Seatback Release Handle 3. Close the tailgate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Raise Rear Seat WARNING! 1. Open the tailgate. 2. Detach pull strap from back of seat and pull seatback upward until it locks into place. Reattach strap. Pull Strap 3. Close the tailgate. The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory NOTE: Each time the S (SET) button and a numbered button 1 or 2 are pressed, you erase the memory settings for that button and store a new one. 1. Insert the ignition key, and turn the ignition switch to the ON position. 2. Press the driver door MEMORY button number 1 if you are setting the memory for driver 1, or button number 2 if you are setting the memory for driver 2.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Turn on the radio and set the radio station presets (up to “Electronic Vehicle Information Center (EVIC) — to 12 AM and 12 FM stations can be set). Customer-Programmable Features” in Section 4 for more information. 6. Turn the ignition switch to the LOCK position and 12. Repeat the above steps to set the next memory remove the key. position, using the other numbered memory button, or to 7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 To recall the memory setting for driver two, press 3. Press and release the memory S (SET) button located MEMORY button number 2 on the driver’s door, or the on the driver’s door. UNLOCK button on the RKE transmitter linked to 4. Within five seconds, press and release MEMORY memory position 2. button 1 on the driver’s door. A recall can be cancelled by pressing any of the 5.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Entry/Exit Seat This feature provides automatic driver’s seat positioning which will enhance driver mobility out of and into the vehicle. driving position when the key is placed into the ignition, and turned out of the LOCK position toward the ACC/ON position. The Easy Entry/Exit feature will be automatically disThere are two possible Easy Entry/Exit adjustments abled if the seat is already positioned closer than 0.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the release lever inside your vehicle located below the instrument panel and in front of the driver’s door. 3 Underhood Safety Latch CAUTION! Hood Release Handle 2. Reach under the hood, move safety latch to the left and lift the hood. To prevent possible damage, do not slam the hood to close it.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are fully latched before driving. LIGHTS Multifunction Lever The multifunction lever controls the operation of the headlights, turn signals, headlight beam selection, instrument panel light dimming, passing light, interior courtesy/dome lights and optional fog lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Headlights and Parking Lights Automatic Headlight System — If Equipped Turn the end of the multifunction lever to the first detent Turn the end of the multifunction lever to the third detent for parking light operation. Turn to the second detent for (AUTO) to activate the Automatic Headlight system. headlight operation. Turn to the third detent for Automatic Headlight operation (if equipped).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE This system performs two functions. With the engine approximately four minutes after the wipers completely running and the multifunction lever in the AUTO posi- stop. Refer to “Windshield Wipers and Washers” in this tion, the headlights will turn on and off based on the section for more information. surrounding light levels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 NOTE: If the windshield or SmartBeam™ mirror is To Deactivate replaced, the SmartBeam™ mirror must be re-aimed to 1. Pull back on the multifunction lever to manually ensure proper performance. See your local authorized deactivate the system (normal operation of high beams). dealer. 2. Pull back on the multifunction lever once again to To Activate reactivate the system. 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Daytime Running Lights — If Equipped The high beam headlights come on at a low intensity level whenever the engine is running, and the transmission is not in the PARK position. The lights remain on until the ignition switch is turned OFF or the parking brake is engaged. The headlight switch must be used for normal night time driving. Fog Lights — If Equipped The fog light switch is located in the multifunction lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 • A front fog light is a lighting device providing illumination forward of the vehicle under conditions of fog, rain, snow or dust. The front fog lights supplement the low beams of a standard headlight system. interior lights on. Rotating the control to the “Off” (extreme bottom) position disables all the interior lights, even when the doors and liftgate are open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Battery Saver Feature — Exterior/Interior Lights If the multifunction lever is left in the interior light position, parking light position, or the headlight position when the ignition switch is moved to the OFF position, the battery saver feature will automatically turn off the exterior and interior lights after eight minutes. Normal operation will resume when the ignition is turned ON or when the headlight switch is turned to another position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam. 111 the ignition switch is turned OFF. Only the headlights will illuminate during this time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE by pressing the front recessed area of the lens. To turn WINDSHIELD WIPERS AND WASHERS these lights off, press the recessed area of the lens a The windshield wiper/washer control lever is located on the right side of the steering column. The front wipers are second time. operated by rotating a switch, located on the end of the lever. For information on the rear wiper/washer, refer to “Rear Window Features” in this section.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Rotate the end of the lever upward to the LO position for low-speed wiper operation. Rotate the end of the lever upward to the HI position for high-speed wiper operation. 113 CAUTION! Always remove any buildup of snow that prevents the windshield wiper blades from returning to the “park” position. If the windshield wiper switch is turned off, and the blades cannot return to the “park” position, damage to the wiper motor may occur.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist Use the Mist feature when weather conditions make occasional usage of the wipers necessary. Pull down and release the control lever for a single wiping cycle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 delay interval. The delay can be regulated from a maxi- Rain Sensing Wipers — If Equipped mum of approximately 18 seconds between cycles, to a This feature senses moisture on the windshield and automatically activates the wipers for the driver. The cycle every 1/2 second. feature is especially useful for road splash or overspray from the windshield washers of the vehicle ahead.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Rain Sensing feature may not function properly • Low Ambient Temperature — When the ignition is when ice, or dried salt water is present on the windfirst turned ON, the Rain Sensing system will not shield. operate until the wiper switch is moved, vehicle speed is greater than 0 mph (0 km/h), or the outside tem• Use of Rain-X威 or products containing wax or silicone perature is greater than 32°F (0°C). may reduce Rain Sensing performance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. 117 To unlock the steering column, push the control handle downward (toward the floor). To tilt the steering column, move the steering wheel upward or downward as desired.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE improved position with the steering wheel. The adjustable pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. The position of the brake and accelerator pedals can be adjusted without compromising safety or comfort in actuating the pedals. Press the bottom of the switch to move the pedals forward (away from the driver). Press the top of the switch to move the pedals rearward (toward the driver).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! The Electronic Speed Control lever is located on the right side of the steering wheel. Do not place any article under the adjustable pedal’s or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. 3 WARNING! Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated simultaneously. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The Cruise Indicator Light in the instrument cluster will illuminate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Deactivate A soft tap on the brake pedal, pulling the Electronic Speed Control lever toward you, or normal brake pressure while slowing the vehicle will deactivate Electronic Speed Control without erasing the set speed memory. Pressing the ON/OFF button or turning off the ignition switch erases the set speed memory.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The Rear Park Assist can be active only when the shift lever is in REVERSE. If the Rear Park Assist is enabled at this shift lever position, the system will be active until the vehicle speed is increased to approximately 11 mph (18 km/h) or above.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Park Assist Warning Display The Rear Park Assist Warning Display, located in the headliner near the flipper glass, provides both visible and audible warnings to indicate the distance between the rear fascia and the detected obstacle. 123 When the ignition is turned to the ON position, the warning display will turn ON all of its LEDs for about one second. Each side of the warning display has six yellow and two red LEDs.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING DISPLAY DISTANCES DISPLAY LED 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED 8th LED OBSTACLE DISTANCE FROM: REAR CORNERS REAR CENTER 59 in (150 cm) 51 in (130 cm) 45 in (115 cm) 31.5 in (80 cm) 39 in (100 cm) 25.5 in (65 cm) 33.5 in (85 cm) 20 in (50 cm) 28 in (70 cm) 16 in (40 cm) 20 in (50 cm) 6 in (15 cm) 12 in (30 cm) NOTE: The Rear Park Assist system will MUTE the radio, if on, when the system is sounding an audio tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the switch is pressed to disable the system, the instrument cluster will display the “PARK ASSIST DISABLED” message. Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. When the shift lever is changed to REVERSE and the system is disabled, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display the message.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When you turn off the Rear Park Assist System, the instrument cluster will display “PARK ASSIST DISABLED.” Furthermore, once you turn off the Rear Park Assist System, it remains off until you turn it on again, even if you cycle the ignition key. (EVIC) will display “SERVICE PARK ASSIST SYSTEM”. If this occurs making sure the rear fascia/ bumper is free from snow, ice, mud, dirt and debris, see your authorized dealer.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 CAUTION! WARNING! • The Rear Park Assist System is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using the Rear Park Assist System to be able to stop in time when the obstacle is detected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Before using the Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns on the single flashing arc and sounds the continuous tone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • To avoid vehicle damage, the Rear Camera system should only be used as a parking aid. The Rear Camera system is unable to view every obstacle or object in your drive path. • To avoid vehicle damage, the vehicle must be driven slowly when using the Rear Camera system to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/her shoulder when using the Rear Camera system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning the Rear Camera On or Off — Without Navigation Radio 1. Press the ⬙menu⬙ hard key. 2. Select ⬙system setup⬙ soft key. OVERHEAD CONSOLE — IF EQUIPPED The overhead console contains an optional universal garage door opener (HomeLink威), storage for sunglasses, and optional power sunroof switches. GARAGE DOOR OPENER — IF EQUIPPED 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! HomeLink威 Buttons NOTE: HomeLink威 is disabled when the Vehicle Security Alarm is active. • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink姞 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the HomeLink威 buttons while keeping the EVIC display in view. Before You Begin If you have not trained any of the HomeLink威 buttons, erase all channels before you begin training. For optimal training, point the battery end of the handheld transmitter away from the HomeLink威. To do this, press and hold the two outside buttons for up to 20 seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 NOTE: Some gate operators and garage door openers This can usually be found where the hanging antenna may require you to replace Step 3 with procedures noted wire is attached to the garage door opener motor (it is in the “Gate Operator/Canadian Programming” section. NOT the button normally used to open and close the door). 4. Press and hold the just-trained HomeLink威 button. If the channel has been trained, the EVIC display will now state “CHANNEL # TRANSMIT.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Firmly press and release the “LEARN” or “TRAIN- Gate Operator/Canadian Programming ING” button. The name and color of the button may vary Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of by manufacturer. transmission – which may not be long enough for NOTE: There are 30 seconds in which to initiate the next HomeLink威 to pick up the signal during programming.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 If you unplugged the device for training, plug it back in 2. Press and hold the desired HomeLink威 button for 20 seconds until the EVIC display states “CHANNEL # at this time. TRAINING.” Do not release the button. Then proceed with Step 4 under “Programming 3. Without releasing the button, proceed with ProgramHomeLink威” earlier in this section. ming HomeLink威 Step 2 and follow all remaining steps.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. This device must accept any interference that may be Troubleshooting Tips If you are having trouble programming HomeLink威, here received including interference that may cause undesired operation. are some of the most common solutions: • Replace the battery in the original transmitter. NOTE: The transmitter has been tested and it complies with FCC and IC rules.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located on the overhead console. Power Sunroof Switch 137 WARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express Press the switch rearward and release, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. sunroof will automatically retract. Remove the obstruction if this occurs. Next, press the switch forward and release to Express Close.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Sunshade Operation Sunroof Maintenance The sunshade can be opened manually. However, the Use only a non-abrasive cleaner and a soft cloth to clean sunshade will open automatically as the sunroof opens. the glass panel. NOTE: The sunshade cannot be closed if the sunroof is Ignition Off Operation The power sunroof switches remain active for 10 minutes open. after the ignition switch has been turned OFF.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Hold onto shade handle until shade is com- ELECTRICAL POWER OUTLETS Your vehicle is equipped with 12 Volt power outlets that pletely open or closed. can be used to power cellular phones, small electronics and other low powered electrical accessories. The power outlets are labeled with either a “key” or a “battery” symbol to indicate how the outlet is powered.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 • To ensure proper operation a MOPAR威 knob and The power outlet located on the left side of the tray can element must be used. be used to power a conventional cigar lighter. The front power outlets are located to the left and right of The rear power outlet (if equipped) is located in the left the convenience tray (lower center of instrument panel). rear cargo area. Pull lightly on the tab of the plastic cover to access these power outlets.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! (Continued) To avoid serious injury or death: • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 POWER INVERTER — IF EQUIPPED There is a 115 Volt, 150 Watt inverter outlet located on the back of the center console to convert DC current to AC current. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will most power tools.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE may have to be reset manually. To reset the inverter manually press the power inverter button OFF and ON. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. Press the power inverter switch (located on the upper switch bank) to turn the power on to the outlet. Press the switch again to turn the power off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! To avoid serious injury or death: • Do not use a three-prong adaptor. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled it may cause an electric shock and failure. 3 CUPHOLDERS Front Cupholders There are two cupholders for the front seat passengers, located in the center console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cupholders — Second Row Seat Cupholders — Third Row Seat The second row seat has two cupholders in the center The third row seat passengers have cupholders on the left armrest. Lower the center armrest. Refer to “Seats” in this and right rear trim panels. section. Press the front of the cupholder, and the cupholder will come out of the armrest.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 CARGO AREA FEATURES Cargo Load Floor The panel in the load floor is reversible for added utility. One side is carpeted and the other side features a plastic lined tray which holds a variety of items. 3 The cargo load floor is held by spring loaded latches. In order to use the cargo load floor, use the following procedure: Rear Storage Cover NOTE: The cargo load floor latches should not be used as cargo tie-downs.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Flip up pull loop(s) so they are perpendicular (straight 4. Pull up on loop(s) and twist 90 degrees, so they are up) to the top surface of the tray. perpendicular (straight up) to the slotted hole in tray. 2. Pull up on loop(s) and twist 90 degrees, so they are parallel to the slotted hole in tray. 5. Push loop(s) back down, so they are parallel to the top of the tray. 3. Lift tray over loop(s), and reposition tray.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Rotate the switch upward to the “washer” position to activate that rear washer. The washer pump will continue to operate as long as the lever or ring is engaged. Upon release, the wipers will cycle two times before returning to the set position. If the rear wiper is operating when the ignition is turned OFF, the wiper will automatically return to the “park” position if power accessory delay is active.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Window Defroster The rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 NOTE: If not equipped with crossbars, your authorized dealer can order and install MOPAR威 crossbars built specifically for this roof rack system. Distribute cargo weight evenly on the roof rack crossbars. The roof rack does not increase the total load carrying capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not exceed the maximum vehicle load capacity.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE The optional crossbars must also be secured in one of the • If the rear crossbar (or any metallic object) is placed five detent positions marked with an arrow on the over the satellite radio antenna (if equipped), you may siderails to prevent movement. To move the crossbars, experience interruption of satellite radio reception.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg). Always distribute heavy loads as evenly as possible and secure the load appropriately. • Long loads which extend over the windshield, such as wood panels or surfboards, or loads with large frontal area should be secured to both the front and rear of the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 158 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 159 䡵 Instrument Cluster Description . . . . . . . . . . . . 160 䡵 Electronic Vehicle Information Center (EVIC) . . 170 ▫ Electronic Vehicle Information Center (EVIC) Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 ▫ Engine Oil Change Indicator System . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 Sales Code RES — AM/FM Stereo Radio With CD Player (MP3 AUX Jack) . . . . . . . . . . . . . . . 189 ▫ Operating Instructions — Radio Mode . . . . . 189 ▫ Operation Instructions — CD Mode For CD And MP3 Audio Play . . . . . . . . . . . . . . . . . 192 ▫ Notes On Playing MP3 Files . . . . . . . . . . . . 194 ▫ Operation Instructions - Auxiliary Mode . . . . 197 䡵 Sales Code RES/RSC — AM/FM Stereo Radio With CD Player (MP3 AUX Jack) And Sirius Radio. . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Selecting uconnect™ studios (Satellite) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . 216 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . . 216 ▫ Operating Instructions - uconnect™ studios (Satellite) Mode . . . . . . . . . . . . . . . . . . . . . 217 ▫ Operating Instructions - uconnect™ phone (If Equipped) . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 2 3 4 — Air Outlet — Instrument Cluster — Radio — Glove Compartment 5 6 7 8 — — — — Upper Switch Bank Power Outlet/Cigar Lighter Storage Bin Power Outlet 9 — Lower Switch Bank 10 — Climate Controls 11 — Ignition Switch 12 — Storage Bin
UNDERSTANDING YOUR INSTRUMENT PANEL 159 INSTRUMENT CLUSTER 4
UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Speedometer Indicates vehicle speed. 2. Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately. 161 The light also will turn on when the parking brake is applied with the ignition switch in the ON position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 5. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system called OBD II that monitors engine and automatic transmission control systems. The light will illuminate when the key is in the ON position before engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor fuel quality, etc.
UNDERSTANDING YOUR INSTRUMENT PANEL 6. Airbag Warning Light This light turns on and remains on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not on during starting, stays on, or turns on while driving, have the system inspected by an authorized dealer as soon as possible. 163 If the ABS light is on, the brake system should be serviced as soon as possible to restore the benefits of Anti-Lock brakes.
UNDERSTANDING YOUR INSTRUMENT PANEL 12. Tire Pressure Monitoring Telltale Light 10. Oil Pressure Warning Light Each tire, including the spare (if provided), This light indicates low engine oil pressure. The should be checked monthly, when cold and light should turn on momentarily when the engine inflated to the inflation pressure recommended is started. If the light turns on while driving, stop the by the vehicle manufacturer on the vehicle vehicle and shut off the engine as soon as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 reduces fuel efficiency and tire tread life, and may affect approximately one minute and then remain continuously the vehicle’s handling and stopping ability. illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists.
UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealership for service if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 167 15. TOW/HAUL Indicator Light — If Equipped This light will illuminate when the TOW/ HAUL button has been selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 17. 4WD LOW Mode Indicator — If Equipped This light alerts the driver that the vehicle is in the 4WD LOW mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. 18. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for five to eight seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound.
UNDERSTANDING YOUR INSTRUMENT PANEL 169 see your authorized dealer for service as soon as possible. 21. Shift Lever Indicator The Shift Lever Indicator is self-contained within the If the light is flashing when the engine is running, instrument cluster. It displays the gear position of the immediate service is required and you may experience reduced performance, an elevated/rough idle or engine automatic transmission. stall and your vehicle may require towing.
UNDERSTANDING YOUR INSTRUMENT PANEL electrical devices or increase engine speed (if at idle). If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an authorized dealer. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster.
UNDERSTANDING YOUR INSTRUMENT PANEL • Vehicle Information Warning Message Displays • Personal Settings (Customer-Programmable Features) • Compass Display 171 FUNCTION SELECT Button Press the FUNCTION SELECT button to select the displayed function YES (Y) or NO (N).
UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Vehicle Information Center (EVIC) • SERVICE SECURITY KEY Displays • DRIVER/PASSENGER DOOR OPEN (with graphic) When the appropriate conditions exist, the EVIC displays the following messages: • LEFT/RIGHT REAR DOOR OPEN (with graphic) • TURN SIGNAL ON • X DOORS OPEN (with graphic) • PERFORM SERVICE • LIFTGATE OPEN (with graphic) • DAMAGED KEY — KEY DOES NOT COMMUNI- • CATE • • KEY NOT PROGRAMMED — KEY NOT PRO• GRAMMED • • WRONG KEY — KEY DOES NOT BELON
UNDERSTANDING YOUR INSTRUMENT PANEL • HOOD/GLASS/DOORS OPEN (with graphic) • PARK ASSIST DISABLED • HOOD/GATE/DOOR OPEN (with graphic) • SERVICE SUSPENSION • HOOD/GATE/DOORS OPEN (with graphic) • SERVICE PARK ASSIST SYSTEM • LIFTGLASS/DOOR OPEN (with graphic) • TRANSMISSION OVER TEMP • LIFTGLASS/DOORS OPEN (with graphic) • CHECK SHIFT PROCEDURE • LIFTGLASS/HOOD OPEN (with graphic) • SERVICE 4WD SYSTEM • WASHER FLUID LOW (with graphic) • 4WD SYSTEM IN NEUTRAL • COOLANT LOW (with graphic) • LO
UNDERSTANDING YOUR INSTRUMENT PANEL • MEMORY #1 POSITIONS SET • MEMORY #2 POSITIONS SET • MEMORY SYSTEM DISABLED — SEATBELT BUCKLED (with graphic) • MEMORY SYSTEM DISABLED — VEHICLE NOT IN PARK • DRIVER 1 MEMORY • DRIVER 2 MEMORY • ADJ. PEDALS DISABLED — CRUISE CONTROL SET • ADJ.
UNDERSTANDING YOUR INSTRUMENT PANEL 175 • MANUAL CLOSE TO OPERATE (Power Liftgate indicator system is duty cycle based, which means the engine oil change interval may fluctuate dependent upon Models Only) your personal driving style. • VEHICLE NOT IN PARK Unless reset, this message will continue to display each • IGNITION POSITION time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and • PRESS BRAKE TO START release the MENU button.
UNDERSTANDING YOUR INSTRUMENT PANEL The Trip Functions mode displays the following informaTrip Functions Press and release the MENU button until one of the tion: following Trip Functions displays in the EVIC: Average Fuel Economy / Fuel Saver Mode • Average Fuel Economy/Fuel Saver Mode (5.7L Engine Shows the average fuel economy since the last reset. Only) When the fuel economy is reset, the display will read “RESET” or show dashes for two seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 177 4 Fuel Saver Mode — On Fuel Saver Mode — Off This feature allows you to monitor when you are driving Distance To Empty (DTE) in a fuel efficient manner, and it can be used to modify Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is driving habits in order to increase fuel economy.
UNDERSTANDING YOUR INSTRUMENT PANEL and average fuel economy, according to the current fuel Trip B tank level. DTE cannot be reset through the FUNCTION Shows the total distance traveled for Trip B since the last reset. SELECT button. NOTE: Significant changes in driving style or vehicle Elapsed Time loading will greatly affect the actual drivable distance of Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position.
UNDERSTANDING YOUR INSTRUMENT PANEL 179 the FUNCTION SELECT button for two seconds. Current NOTE: A good calibration requires a level surface and an environment free from large metallic objects such as display will reset along with other functions buildings, bridges, underground cables, railroad tracks, Compass Display etc. The compass readings indicate the direction the vehicle is facing.
UNDERSTANDING YOUR INSTRUMENT PANEL 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “CAL” indicator turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences, the variance should be set for the zone where the vehicle is driven, per the zone map.
UNDERSTANDING YOUR INSTRUMENT PANEL 181 4. Press and release the FUNCTION SELECT button to FUNCTION SELECT button while in this display to change the variance number. Continue until desired select English, Espanol, or Francais. Then, as you continue, the information will display in the selected lannumber is reached. guage. 5. Press either MENU, SCROLL, or COMPASS/TEMP NOTE: The EVIC will not change the uconnect™ lanbutton to set the value and exit. guage selection.
UNDERSTANDING YOUR INSTRUMENT PANEL opened. To make your selection, press and release the feature may be selected with or without the flash lights FUNCTION SELECT button until YES (Y) or NO (N) on lock/unlock feature. To make your selection, press and release the FUNCTION SELECT button until YES (Y) appears. or NO (N) appears.
UNDERSTANDING YOUR INSTRUMENT PANEL Auto High Beams (Available with SmartBeam™ Only) When this feature is selected, the high beam headlights will deactivate automatically under certain conditions. To make your selection, press and release the FUNCTION SELECT button until YES (Y) or NO (N) appears. Refer to “Lights/SmartBeam™ — If Equipped” in Section 3 of this manual for more information.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The seat will return to the memorized seat location (if Recall Memory with Remote Key Unlock is set to ON) when the RKE transmitter is used to unlock the door. Refer to “Easy Entry/Exit Seat” under “Driver Memory Seat” in Section 3 of this manual for more information. unlocked with the RKE transmitter. To make your selection, press and release the FUNCTION SELECT button until “OFF,” “30 sec.,” “60 sec.,” or “90 sec.” appears.
UNDERSTANDING YOUR INSTRUMENT PANEL 185 Display ECO — If Equipped The “ECO” message is located in the Compass/ Temperature display, this message can be turned on or off. To make your selection, press and release the FUNCTION SELECT button until “ON” or “OFF” appears.
UNDERSTANDING YOUR INSTRUMENT PANEL • Your system can be set to display pressure units in PSI, Operating Instructions — Voice Recognition kPa, or BAR. System (VR) — If Equipped Refer to “Voice Recognition System (VR)” in the SALES CODE (RER/REN) — AM/FM/CD/DVD uconnect™ User Manual located on the DVD for further RADIO – IF EQUIPPED details. NOTE: The sales code is located on the lower right side Operating Instructions — uconnect™ phone — If of the unit’s faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL To Manually Set the Clock — RER/REN 1. Turn on the radio. 187 6. To save the new time setting, touch the screen where the word “Save” is displayed. Changing Daylight Savings Time When selected, this feature will display the time of day in 3. Touch the screen where “User Clock” is displayed. The daylight savings time. Proceed as follows to change the current setting: clock setting menu will appear on the screen. 2. Touch the screen where the time is displayed. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 2. Touch the screen where the time is displayed. The Show Time if Radio is Off When selected, this feature will display the time of day clock setting menu will appear on the screen. on the touch screen when the radio is turned off. Proceed 3. Touch the screen where the words “Set Time Zone” are as follows to change the current setting: displayed. The time zone selection menu will appear on the screen. 1. Turn on the radio. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) 189 Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio. side of the radio faceplate. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio 4. Adjust the minutes using the right side TUNE/ will remain tuned to the new station until you make SCROLL control knob. Press the TUNE/SCROLL control another selection. Holding either button will bypass knob to save time change. stations without stopping, until you release it. 5. To exit, press any button/knob, or wait five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL 191 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones. Press the buttons to select either AM or FM mode. Push the rotary TUNE/SCROLL control knob a third SET/RND Button — To Set the Pushbutton time and TREBLE will display.
UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice.
UNDERSTANDING YOUR INSTRUMENT PANEL 193 If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number, and index time in minutes and seconds. Play will begin at the start of track 1. If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded.
UNDERSTANDING YOUR INSTRUMENT PANEL Press the RND button a second time to stop Random TIME Button Press this button to change the display from a large CD Play. playing time display to a small CD playing time display. Notes on Playing MP3 Files RW/FF The radio can play MP3 files; however, acceptable MP3 Press and hold the FF (Fast Forward) button and the CD file recording media and formats are limited.
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal Maximum number of folder levels: 8 CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after Maximum number of files: 255 writing⬙ are most likely multisession discs. The use of Maximum number of folders.
UNDERSTANDING YOUR INSTRUMENT PANEL rates (VBR) are also supported. The majority of MP3 files Playback of MP3 Files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium VBR bit rate. contains a lot of folders or files, the radio will take more MPEG SpecifiSampling FreBit Rate (kbps) time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device, such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. 197 SALES CODE RES/RSC — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make NOTE: The ignition switch must be in the ON or ACC another selection. Holding either button will bypass position to operate the radio. stations without stopping until you release it.
UNDERSTANDING YOUR INSTRUMENT PANEL Phone Button uconnect™ phone — If Equipped Press this button to operate the uconnect™ phone feature (if equipped). Refer to “uconnect™ phone” in the uconnect™ User Manual located on the DVD for further details. 199 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob.
UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text message broadcast from an FM station (FM mode only). Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones.
UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade. MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information.
UNDERSTANDING YOUR INSTRUMENT PANEL Program Type Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display Soft Soft Rck Soft R&B Sports Talk Top 40 Weather SETUP Button Pressing the SETUP button allows you to select between the following items: • Set Clock — Pressing the SELECT button will allow you to set the clock. Adjust the hours by turning the TUNE/SCROLL control knob. After adjusting the hours, press the TUNE/SCROLL control knob to set the minutes.
UNDERSTANDING YOUR INSTRUMENT PANEL window. Select the button (1–6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET/ RND button, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the display window.
UNDERSTANDING YOUR INSTRUMENT PANEL Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than 1.0 in (2.5 cm), a disc may already be loaded and must be ejected before a new disc can be loaded. CAUTION! (Continued) • Do not use adhesive labels. These labels can peel away and jam the player mechanism.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 NOTE: Ejecting with the ignition OFF is not allowed on AM/FM Button Press the button to select either AM or FM mode. convertible or soft-top models (if equipped). SEEK Button Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection.
UNDERSTANDING YOUR INSTRUMENT PANEL Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With 200 files, exceeding 50 folders will result in this display.
UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported.
UNDERSTANDING YOUR INSTRUMENT PANEL Loading times for playback of MP3 files may be affected begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain by the following: playable files). • Media - CD-RW media may take longer to load than The folder list will time out after five seconds.
UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. 209 Operating Instructions - uconnect™ phone (If Equipped) Refer to “uconnect™ phone” in the uconnect™ User Manual located on the DVD for further details.
UNDERSTANDING YOUR INSTRUMENT PANEL This feature allows you to plug an iPod威 into the Connecting The iPod姞 vehicle’s sound system through a 16–pin connector, using Use the provided connection cable to connect an iPod威 to the vehicle’s 16–pin connector port (which is located in the provided interface cable. the glove compartment on some vehicles). Once the UCI supports Mini, 4G, Photo, Nano, 5G iPod威 and iPod威 is connected and synchronized to the vehicle’s UCI iPhone威 devices.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 Using This Feature Play Mode By using the provided connection cable to connect an When switched to UCI mode, the iPod威 automatically iPod威 to the vehicle’s UCI 16–pin connector port: starts Play mode.
UNDERSTANDING YOUR INSTRUMENT PANEL • Jump backward in the current track by pressing and • While a track is playing, press the INFO button to see holding the << RW button. Holding the << RW the associated metadata (artist, track title, album, etc.) button long enough will take you to the beginning for that track. Pressing the INFO button again jumps of the current track. to the next screen of data for that track.
UNDERSTANDING YOUR INSTRUMENT PANEL • RND button (available on sales code RES radio only): Pressing this button toggles between Shuffle ON and Shuffle OFF modes for the iPod威. If the RND icon is showing on the radio display, then the shuffle mode is ON. List Or Browse Mode During Play mode, pressing any of the buttons described below, takes you to List mode. List mode enables you to scroll through the list of menus and tracks on the iPod威.
UNDERSTANDING YOUR INSTRUMENT PANEL • Pressing a PRESET button will display the current list on the top line and the first item in that list on the second line. • To Exit List mode without selecting a track, press the same PRESET button again to go back to Play mode. • LIST button: The LIST button will display the top level menu of the iPod威. Turn the TUNE control knob to list the top-menu item you wish to select and press the TUNE control knob.
UNDERSTANDING YOUR INSTRUMENT PANEL uconnect™ studios (SATELLITE RADIO) — IF EQUIPPED (REN/RER/RES RADIOS ONLY) Satellite radio uses direct satellite-to-receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
UNDERSTANDING YOUR INSTRUMENT PANEL Sirius ID number will display. The Sirius ID number bikes should be placed as far rearward as possible, within display will time out in two minutes. Press any button on the loading design of the rack. Do not place items directly on or above the antenna. the radio to exit this screen. ESN/SID Access With REN/RER Radios Reception Quality While in SAT mode, press the MENU button on the radio Satellite reception may be interrupted due to one of the faceplate.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 INFO Button Pressing the INFO button will cycle the display information between Artist, Song Title, and Composer (if availNOTE: The ignition switch must be in the ON or ACC able). Also, pressing and holding the INFO button for an position to operate the radio. additional three seconds will make the radio display the SEEK Buttons Song Title all of the time (press and hold again to return Press and release the SEEK buttons to search for the next to normal display).
UNDERSTANDING YOUR INSTRUMENT PANEL or turning the TUNE/SCROLL control knob within five • Display Sirius ID number — Press the AUDIO/ seconds will allow the program format type to be seSELECT button to display the Sirius ID number. This lected. number is used to activate, deactivate, or change the Sirius subscription. Toggle the MUSIC TYPE button again to select the music SET Button – To Set the Pushbutton Memory type.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 pushbutton memory. The channels stored in SET 2 service provider is SIRIUS Satellite Radio. SIRIUS Backmemory can be selected by pressing the pushbutton seat TV™ offers three video channels for family entertainment, directly from its satellites and broadcasting twice. studios. Every time a preset button is used, a corresponding NOTE: SIRIUS service is not available in Hawaii and button number will display. has limited coverage in Alaska.
UNDERSTANDING YOUR INSTRUMENT PANEL The LCD screen is located on the headliner behind the front seats. Remote Control Location Lowering the Display Screen REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 Pressing the center button will make the radio switch between the various modes available (AM/FM/TAPE/ CD, etc.). The left-hand control is a rocker-type switch with a pushbutton in the center. The function of the left-hand control is different depending on which mode you are in. The following describes the left-hand control operation in each mode.
UNDERSTANDING YOUR INSTRUMENT PANEL CD Player Pressing the top of the switch once will go to the next track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track, or to the beginning of the previous track if it is within one second after the current track begins to play. CD/DVD MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 6. Do not expose the disc to direct sunlight. 223 CLIMATE CONTROLS 7. Do not store the disc where temperatures may become Manual Heating and Air Conditioning System — If too high. Equipped The controls for the heating and air conditioning system NOTE: If you experience difficulty in playing a particuin this vehicle consist of a series of rotary knobs. These lar disc, it may be damaged (i.e.
UNDERSTANDING YOUR INSTRUMENT PANEL The instrument panel features four dual-vane airflow Temperature Control The temperature control rotary knob registers. Two registers are located on the outer ends of (in the center) controls the air temthe instrument panel and two are located in the center of perature. The coldest temperature setthe instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 directed to the front door windows through the side Bi-Level window demister grilles. Some airflow is delivered to the Air flows both through the outlets located in the instrument panel and those located on the floor. Air floor while in defrost so that comfort can be maintained. flows through the registers in the back of the center Defrost/Floor console, and under the front seats to the rear seat Air flows through the front and rear floor outlets passengers.
UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation The recirculation feature can be selected with the mode control knob. You may choose between Bi-Level Recirculation and Panel Recirculation air outlets while in this mode. Normally, air enters from outside the vehicle. However, when in Recirculation mode air inside the vehicle is re-used. Use this mode to rapidly cool the inside of the vehicle. The Recirculation mode can also be used to temporarily block out outside odors, smoke, and dust.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 Turn the mode control (on the right) knob to AUTO, and place the blower control (on the left) to either LO AUTO or HI AUTO. The LO AUTO position should be used for front seat occupants only. The HI AUTO position should be used when more airflow is desired, or when rear seat occupants are present. Dial in the comfort setting you would like the system to maintain by rotating the driver’s or passenger’s control knob.
UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The temperature setting can be adjusted at any Recirculation time without affecting automatic control operation. HowThe system will automatically control recircuever, if the driver and/or passenger temperature knobs lation. However, pressing this button will temare set to the full hot or full cold positions, the air porarily put the system in Recirculation mode.
UNDERSTANDING YOUR INSTRUMENT PANEL • To provide you with maximum comfort in the automatic mode, during cold start-ups the blower fan will remain off until the engine warms up. However, the fan will engage immediately if the defrost mode is selected or if you manually select a blower speed. • Under certain conditions (after the vehicle is turned off) the climate control system may recalibrate and a noise may be heard for 20 seconds. This is part of normal operation. 229 mode at this time.
UNDERSTANDING YOUR INSTRUMENT PANEL
UNDERSTANDING YOUR INSTRUMENT PANEL 231 NOTE: Regardless of the type of operation, when a NOTE: The defrost mode is not automatically selected. temperature knob is set to the full clockwise or full It must be manually selected, when desired. counterclockwise position, the system will deliver full Defrost/Floor hot or full cold air out of the ducts, respectively.
UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Air flows both through the outlets located in the instrument panel and those located on the floor. Air flows through the registers in the back of the center console, and under the front seats to the rear seat passengers. These registers can be closed to block airflow. The center console outlets deliver conditioned air while the floor outlets deliver heated air. outlets selected on the mode control dial.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 Recirculation mode to be selected while in the defrost or defrost/floor modes. Attempting to use Recirculation while in these modes will cause the LED in the button to blink and then turn off. Rear Climate Control — If Equipped The Manual Rear Climate Control system has one floor air outlet (passenger side), and two panel outlets in the rear quarter trim (on each side). The unit provides warm or cool air through the floor and upper outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Rear Blower Control The left knob on the Rear Control Panel has four positions, “Off”, and a range of three blower speeds. This allows the third row seat occupants to control the volume of air circulated in the rear of the vehicle. CAUTION! Rear Control Panel NOTE: The rear climate control system cannot be controlled from the front seat; it can only be turned on and off. All control of the rear system must be performed by the rear occupants.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 Panel Rear Temperature Control Air flows through the outlets located in the rear The center knob on the Rear Control Panel allows the quarter trim panels. These registers can be closed to third row seat occupants to have control of the rear block airflow. temperature as follows: • When the temperature knob is in the cold (Blue) Operating Tips position, cold air will be delivered from the outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Operating Tips Chart 4
STARTING AND OPERATING CONTENTS 䡵 Starting Procedure . . . . . . . . . . . . . . . . . . . . . 243 ▫ Brake/Transmission Shift Interlock System . . 247 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 243 ▫ Brake/Transmission Interlock Manual Override . . . . . . . . . . . . . . . . . . . . . . . . . . 247 ▫ Extreme Cold Weather (Below ⫺20°F Or ⫺29°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244 ▫ Five–Speed Automatic Transmission . . . . . . . 248 ▫ If Engine Fails To Start .
STARTING AND OPERATING ▫ Quadra-Trac II威 Operating Instructions/ 䡵 Power Steering . . . . . . . . . . . . . . . . Precautions — If Equipped . . . . . . . . . . . . . 256 ▫ Power Steering Fluid Check . . . . . . ▫ Shift Positions . . . . . . . . . . . . . . . . . . . . . . 257 䡵 Parking Brake . . . . . . . . . . . . . . . . . ▫ Shifting Procedures . . . . . . . . . . . . . . . . . . . 258 䡵 Anti-Lock Brake System . . . . . . . . . . ▫ Quadra-Drive威 II System — If Equipped . . . .
STARTING AND OPERATING ▫ Hill Start Assist (HSA) – Four-Wheel Drive Models With NV245 Two–Speed Transfer Case Only . . . . . . . . . . . . . . . . . . . . . . . . . 280 ▫ Hill Descent Control (HDC) – Four-Wheel Drive Models With NV245 Two–Speed Transfer Case Only . . . . . . . . . . . . . . . . . . . 283 ▫ ESP/BAS Warning Light And ESP/TCS Indicator Light . . . . . . . . . . . . . . . . . . . . . . 285 䡵 Tire Safety Information 241 ▫ Radial-Ply Tires . . . . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING ▫ 3.7 Engine . . . . . . . . . . . . . . . . . . . . . . . . . 314 䡵 Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 323 ▫ 5.7L Engine . . . . . . . . . . . . . . . . . . . . . . . . 314 ▫ Common Towing Definitions . . . . . . . . . . . . 323 ▫ Reformulated Gasoline . . . . . . . . . . . . . . . . 315 ▫ Trailer Hitch Classification . . . . . . . . . . . . . . 327 ▫ Gasoline/Oxygenate Blends . . . . . . . . . . . . .
STARTING AND OPERATING STARTING PROCEDURE Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. WARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition.
STARTING AND OPERATING Extreme Cold Weather (Below ⫺20°F or ⫺29°C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended. If Engine Fails To Start WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury.
STARTING AND OPERATING release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds. Once this occurs, release the accelerator pedal, turn the ignition switch to the LOCK position, wait 10 to 15 seconds, then repeat the “Normal Starting” procedure. CAUTION! To prevent damage to the starter, wait 10 to 15 seconds before trying again. 245 electrical outlet with a grounded, three-wire extension cord.
STARTING AND OPERATING AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, PARK, or NEUTRAL into any forward gear when the engine is above idle speed.
STARTING AND OPERATING Brake/Transmission Shift Interlock System This vehicle is equipped with a Brake Transmission Shift Interlock System (BTSI) that holds the shift lever in the PARK position when the ignition switch is in the LOCK position. To move the shift lever out of the PARK position, the ignition switch must be turned to any other switch position (ACC, ON, or START) (engine running or not) and the brake pedal must be pressed. 247 1. Turn the key to the ON position without starting the engine. 2.
STARTING AND OPERATING Five–Speed Automatic Transmission The electronically controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle, may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles/kilometers. Gear Ranges Interlock Manual Override 6. Move the shift lever into the NEUTRAL position. 7. The vehicle may then be started in NEUTRAL.
STARTING AND OPERATING Never use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, then place the shift lever into the PARK position. WARNING! • Never use the PARK position as a substitute for the parking brake. Always apply parking brake fully when parked to guard against vehicle movement and possible injury or damage.
STARTING AND OPERATING Electronic Range Select (ERS)Operation The Electronic Range Select (ERS) shift control allows you to move the shift lever left (-) or right (+) when the shift lever is in the DRIVE position, allowing you to limit the highest available gear. For example, if the driver shifts the transmission into ERS 3 (third gear), the transmission will never shift above third gear, but can shift down to 2 (second) or 1 (first), when needed. 3.
STARTING AND OPERATING downshift). For example, if you are in DRIVE and are in 3rd (direct) gear, when you tap the shift lever one time to the left (-), the display will show 4 (ERS 4 is direct gear). Another tap to the left (-) will shift the transmission down to ERS 3 (the added underdrive gear). When in the DRIVE position in 5th gear, the first tap to the left (-) will downshift the transmission and display 5 (ERS 5 is the same as normal 4th gear).
STARTING AND OPERATING • transmission temperature. operating OVER TEMP” message may display, and the transmission may downshift out of Overdrive until the transmission cools down. After cool down, the transmission will NOTE: If the vehicle is started in extremely cold temresume normal operation. peratures, the transmission may not shift into Overdrive and will automatically select the most desirable gear for In high ambient temperatures with sustained high engine operation at this temperature.
STARTING AND OPERATING performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in “TOW/HAUL” mode, the transmission will shift into direct gear and Overdrive will be enabled under steady cruise conditions. 253 The “TOW/HAUL Indicator Light” will illuminate in the instrument cluster to indicate when the switch has been activated. Pressing the switch a second time restores normal operation.
STARTING AND OPERATING 3. Turn the engine off, and be sure to turn the key to the higher speeds under heavier acceleration. This may result in a slightly different feeling or response during LOCK position. normal operation in high gear. When the vehicle speed 4. Wait approximately 10 seconds, then restart the endrops below a calibrated speed, or during acceleration, gine. the clutch automatically and smoothly disengages. The feature is operational in Overdrive and in DRIVE. 5.
STARTING AND OPERATING 255 the transmission may not shift into the top Overdrive before attempting to rock the vehicle. Refer to “Electronic gear (normal 5th gear) until the transmission fluid and Brake Control System” in Section 3 of this manual. engine coolant are warm.
STARTING AND OPERATING FOUR-WHEEL DRIVE OPERATION • 4WD HI Quadra-Trac I姞 Operating Instructions/ Precautions — If Equipped The Quadra-Trac I威 is a single-speed (HI range only) transfer case, which provides convenient full-time four– wheel drive. No driver interaction is required. The Brake Traction Control (BTC) System, which combines standard ABS and Traction Control, provides resistance to any wheel that is slipping to allow additional torque transfer to wheels with traction.
STARTING AND OPERATING 257 Proper operation of four-wheel drive vehicles depends Shift Positions on tires of equal size, type, and circumference on each For additional information on the appropriate use of each wheel. Any difference will adversely affect shifting and transfer case mode position, see the information below: cause damage to the transfer case.
STARTING AND OPERATING additional traction and maximum pulling power for loose, slippery road surfaces only. Do not exceed 25 mph (40 km/h). Shifting Procedures 4WD HI to 4WD LOW With the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), key ON or engine running, shift the transmission into NEUTRAL, and raise the transfer case T-handle. The “4WD LOW” indicator light in the instrument cluster will begin to flash and remain on solid when the shift is complete. Release the T-handle.
STARTING AND OPERATING “4WD LOW” indicator light in the instrument cluster will flash and go out when the shift is complete. Release the T-handle. NOTE: • If shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “CHECK SHIFT PROCEDURES” message will flash from the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.
STARTING AND OPERATING Quadra-Drive姞 II System — If Equipped The optional Quadra-Drive威 II System features three torque transfer couplings. The couplings include Electronic Limited-Slip Differential (ELSD) front and rear axles and Quadra-Trac II威 transfer case. The optional ELSD axles are fully automatic and require no driver input to operate. Under normal driving conditions, the units function as standard axles, balancing torque evenly between left and right wheels.
STARTING AND OPERATING ON-ROAD DRIVING TIPS Utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-road applications. Specific design characteristics give them a higher center of gravity than ordinary cars. An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems.
STARTING AND OPERATING CAUTION! When driving through water, do not exceed 5 mph (8 km/h). Always check water depth before entering, as a precaution, and check all fluids afterward. Driving through water may cause damage that may not be covered by the new vehicle limited warranty. and/or the flow rate is reduced. If you must cross flowing water avoid depths in excess of 9 in (23 cm). The flowing water can erode the streambed, causing your vehicle to sink into deeper water.
STARTING AND OPERATING Driving in Snow, Mud and Sand In heavy snow, when pulling a load, or for additional control at slower speeds, shift the transmission to a low gear and shift the transfer case to 4WD LOW if necessary. Refer to “Four-Wheel Drive Operation” in this section. Do not shift to a lower gear than necessary to maintain forward motion. Over-revving the engine can spin the wheels and traction will be lost.
STARTING AND OPERATING If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain forward motion by turning the front wheels slowly. This may provide a fresh “bite” into the surface and will usually provide traction to complete the climb. always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • Completely inspect the underbody of your vehicle.
STARTING AND OPERATING • After extended operation in mud, sand, water, or similar dirty conditions, have brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary.
STARTING AND OPERATING WARNING! CAUTION! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the New Vehicle Limited Warranty.
STARTING AND OPERATING 267 apparent, and/or the system is not functioning as antici- PARKING BRAKE pated. Coordinate inspection efforts through an autho- To set the parking brake, pull the lever up as firmly as possible. When the parking brake is applied with the rized dealer. ignition ON, the “Brake Warning Light” in the instruWARNING! ment cluster will illuminate.
STARTING AND OPERATING WARNING! Parking Brake Be sure the parking brake is firmly set when parked and the shift lever is in the PARK position. When parking on a hill, you should apply the parking brake before placing the shift lever in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of PARK. • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury.
STARTING AND OPERATING When parking on a hill, turn the front wheels toward the curb on a downhill grade, and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. ANTI-LOCK BRAKE SYSTEM The Anti-Lock Brake System (ABS) is designed to aid the driver in maintaining vehicle control under adverse braking conditions.
STARTING AND OPERATING WARNING! WARNING! (Continued) • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. • The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
STARTING AND OPERATING • Do not “ride” the brakes by resting your foot on the pedal. This could overheat the brakes and result in unpredictable braking action, longer stopping distances, or brake damage. • When descending mountains or hills, repeated braking can cause brake fade with loss of braking control. Avoid repeated heavy braking by downshifting the transmission or locking out overdrive whenever possible.
STARTING AND OPERATING help avoid skidding on slippery surfaces during braking. ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with an advanced electronic Refer to “Anti-Lock Brake System” in Section 5 of this brake control system that includes the Anti-Lock Brake manual. System (ABS), Traction Control System (TCS), Brake WARNING! Assist System (BAS), Electronic Roll Mitigation (ERM), and Electronic Stability Program (ESP).
STARTING AND OPERATING Traction Control System (TCS) This system monitors the amount of wheel spin of each of the driven wheels. If wheel spin is detected, brake pressure is applied to the slipping wheel(s) and engine power is reduced to provide enhanced acceleration and stability. A feature of the TCS system functions similar to a limited-slip differential and controls the wheel spin across a driven axle.
STARTING AND OPERATING WARNING! The BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The BAS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING WARNING! Many factors, such as vehicle loading, road conditions and driving conditions, influence the chance that wheel lift or rollover may occur. ERM cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. Only a safe, attentive, and skillful driver can prevent accidents.
STARTING AND OPERATING “ESP/TCS Indicator Light” begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. WARNING! The Electronic Stability Program (ESP) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
STARTING AND OPERATING Partial Off This mode is entered by momentarily pressing the “ESP OFF” switch. When in “Partial Off” mode, the TCS portion of ESP, except for the “limited slip” feature described in the TCS section, has been disabled and the “ESP/TCS Indicator Light” will be illuminated. All other stability features of ESP function normally.
STARTING AND OPERATING mode is overcome, turn ESP back on by momentarily mode, described above. When the vehicle speed drops pressing the “ESP OFF” switch. This may be done while below 35 mph (56 km/h), the ESP system shuts off. ESP is deactivated at low vehicle speeds so that it will not the vehicle is in motion.
STARTING AND OPERATING WARNING! With the ESP switched off, the enhanced vehicle stability offered by ESP and ERM are unavailable. In an emergency evasive maneuver, the ESP and ERM systems will not engage to assist in maintaining stability. The “Full Off” ESP mode is intended for off-road use only. 4WD Low Range 279 (64 km/h), the normal ESP stability function returns, but TCS remains off. When the vehicle speed drops below 35 mph (56 km/h), the ESP system shuts off.
STARTING AND OPERATING WARNING! With the ESP switched off, the enhanced vehicle stability offered by ESP and ERM are unavailable. In an emergency evasive maneuver, the ESP and ERM systems will not engage to assist in maintaining stability. The “Full Off” mode is intended for offroad use only. Trailer Sway Control (TSC) TSC uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway.
STARTING AND OPERATING 281 period of time after the driver takes their foot off of the HSA will work in REVERSE and all forward gears when brake pedal. If the driver does not apply the throttle the activation criteria have been met. The system will not during this short period of time, the system will release activate if the vehicle is placed in NEUTRAL or PARK. brake pressure and the vehicle will roll down the hill.
STARTING AND OPERATING WARNING! WARNING! (Continued) • If you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object behind you.
STARTING AND OPERATING 283 Hill Descent Control (HDC) – Four-Wheel Drive Models With NV245 Two–Speed Transfer Case Only HDC maintains vehicle speed while descending hills during off-road driving situations and is available in 4WD LOW range only. To enable HDC (transfer case must be in 4WD LOW range), press the HDC switch. If the HDC switch is pressed when the vehicle is not in 4WD LOW range, the light in the switch will flash for five seconds and HDC will not be enabled.
STARTING AND OPERATING and will only activate when the vehicle is descending a HDC also has the capability to sense rough terrain, and will automatically adjust to a slightly slower set speed hill. It will usually not activate on level ground. [about 0.3 mph (0.5 km/h) than normal.] The HDC speed may be adjusted by the driver to suit the driving conditions. The speed corresponds to the trans- HDC operation can be overridden with brake application to slow the vehicle down below the HDC control speed.
STARTING AND OPERATING WARNING! HDC is only intended to assist the driver in controlling vehicle speed when descending hills. The driver must remain attentive to the driving conditions and is responsible for maintaining a safe vehicle speed. 285 If the “ESP/BAS Warning Light” comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system, or both.
STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation.
STARTING AND OPERATING 287 Tires designed to this standard have the letter “T” • High flotation tire sizing is based on U.S. design molded into the sidewall preceding the size designastandards and it begins with the tire diameter molded tion. Example: T145/80D18 103M. into the sidewall. Example: 31x10.5 R15 LT. Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....
STARTING AND OPERATING EXAMPLE: 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. 289 Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires.
STARTING AND OPERATING NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard.
STARTING AND OPERATING 6. If your vehicle will be towing a trailer, load from your • For the following example, the combined weight of trailer will be transferred to your vehicle. Consult this occupants and cargo should never exceed 865 lbs manual to determine how this reduces the available (392 kg). cargo and luggage load capacity of your vehicle.
STARTING AND OPERATING 293 5
STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement.
STARTING AND OPERATING CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage it. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the winter.
STARTING AND OPERATING 297 Tire Pressures For High Speed Operation Radial-Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle important. Increased tire pressure and reduced vehicle poorly.
STARTING AND OPERATING WARNING! CAUTION! Temporary use spare tires are for emergency use only. With these tires, do not drive more than 50 mph (80 km/h). Temporary use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control.
STARTING AND OPERATING 299 WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and do not let anyone near a spinning wheel no matter what the speed. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced.
STARTING AND OPERATING Life of Tire Replacement Tires The service life of a tire is dependent upon various The tires on your new vehicle provide a balance of many factors including but not limited to: characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu• Driving style facturer strongly recommends that you use tires equiva• Tire pressure lent to the originals in size, quality and performance when replacement is needed.
STARTING AND OPERATING 301 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
STARTING AND OPERATING • For vehicles equipped with 18 inch wheels, do not • Drive cautiously, avoiding large bumps, potholes and install tire chains or traction devices on tires larger extreme driving maneuvers. than 235/60R18XL. Tires larger than this may not provide sufficient body clearance with chains or other TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at traction devices.
STARTING AND OPERATING 303 NOTE: The premium Tire Pressure Monitor System will TIRE PRESSURE MONITOR SYSTEM (TPMS) automatically locate the pressure values displayed in the The Tire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressure based on the vehicle correct vehicle position following a tire rotation. recommended cold tire pressure. The suggested rotation method is the “forward-cross” The tire pressure will vary with temperature by about shown in the following diagram.
STARTING AND OPERATING The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning threshold for any reason, including low temperature effects, or natural pressure loss through the tire. The TPMS will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recommended cold tire pressure.
STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use aftermarket tire sealants or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.
STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, A tire pressure monitoring sensor is located in the spare and the TPMS will monitor the actual tire pressure in wheel, if the vehicle is equipped with a matching full-size spare wheel and tire assembly. The matching full-size the tire. spare tire can be used in place of any of the four road Base System tires.
STARTING AND OPERATING 307 pressures have been received. The vehicle may need to be 3. Lots of snow or ice around the wheels or wheel driven for up to 20 minutes above 15 mph (24 km/h) to housings. receive this information. 4. Using tire chains on the vehicle. The Tire Pressure Monitoring Telltale Light will flash on 5. Using wheels/tires not equipped with TPM sensors. and off for 75 seconds, and remain on solid when a NOTE: system fault is detected.
STARTING AND OPERATING • If your vehicle is not equipped with a matching full-size spare wheel and tire assembly, it does not have a tire pressure monitoring sensor in the spare tire. The TPMS will not be able to monitor the tire pressure.
STARTING AND OPERATING 309 The Tire Pressure Monitor System (TPMS) consists of the tires. A low spare tire will set the “SPARE LOW PRESSURE” message, but it will not cause the Tire Pressure following components: Monitoring Telltale Light to illuminate or the chime to • Receiver Module sound.
STARTING AND OPERATING NOTE: Your system can be set to display pressure units The system will automatically update, the graphic disin PSI, kPa, or BAR. play of the pressure value(s) will stop “flashing,” and the Tire Pressure Monitoring Telltale Light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information.
STARTING AND OPERATING 311 1. Jamming due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPM sensors. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists.
STARTING AND OPERATING received from the TPM Sensors. However, the system still needs to be serviced as long as the ⬙CHECK TPM SYSTEM⬙ message exists. NOTE: • If your vehicle is equipped with a matching full-size spare wheel and tire assembly, it has a tire pressure monitoring sensor, and can be monitored by the Tire Pressure Monitoring System (TPMS).
STARTING AND OPERATING Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds and then remain on solid, and the EVIC will display a ⬙CHECK TPM SYSTEM⬙ message for three seconds and then display dashes (- -) in place of the pressure value. Once you repair or replace the original road tire, and reinstall it on the vehicle in place of the spare tire, the TPMS will update automatically.
STARTING AND OPERATING FUEL REQUIREMENTS 3.7 Engine All engines (except 5.7L engines) are designed to meet all emissions regulations and provide excellent fuel economy and performance when using high-quality unleaded “regular” gasoline having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines. 5.7L Engine The 5.
STARTING AND OPERATING Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasoline contains oxygenates, and are specifically blended to reduce vehicle emissions and improve air quality. 315 CAUTION! DO NOT use gasoline containing Methanol. Use of these blends may result in starting and drivability problems and may damage critical fuel system components.
STARTING AND OPERATING • OBD II “Malfunction Indicator Light” on blended with MMT provides no performance advantage beyond gasoline of the same octane number without • poor engine performance MMT. Gasoline blended with MMT reduces spark plug life and reduces emission system performance in some • poor cold start and cold drivability vehicles. The manufacturer recommends that gasoline • increased risk for fuel system component corrosion without MMT be used in your vehicle.
STARTING AND OPERATING 317 conditions and would result in additional cost. Therefore, • The use of fuel additives which are now being sold as you should not have to add anything to the fuel. octane enhancers is not recommended. Most of these products contain high concentrations of Methanol. Fuel System Cautions Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not CAUTION! the responsibility of the manufacturer.
STARTING AND OPERATING • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period. If the vehicle is stopped in an open area with the engine running for more than a short period, adjust the ventilation system to force fresh, outside air into the vehicle.
STARTING AND OPERATING 319 CAUTION! WARNING! • Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impurities into the fuel system. Also, a poorly fitting aftermarket cap can cause the “Malfunction Indicator Light” (MIL) to illuminate, due to fuel vapors escaping from the system. • A poorly fitting gas cap may cause the MIL to turn on.
STARTING AND OPERATING Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “CHECK GASCAP” message will be displayed in the EVIC (Electronic Vehicle Information Center). Refer to “Electronic Vehicle Information Center” in Section 4 of this manual. Tighten the fuel filler cap until a “clicking” sound is heard. This is an indication that the fuel filler cap is properly tightened.
STARTING AND OPERATING This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and indicates the month, day, and hour of manufacture. The bar code that appears on the bottom of the label is your VIN. 321 Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.
STARTING AND OPERATING should then be determined separately to be sure that the Inflation Pressure This is the cold tire inflation pressure for your vehicle for load is properly distributed over front and rear axle. Weighing the vehicle may show that the GAWR of either all loading conditions up to full GAWR. the front or rear axles has been exceeded, but the total Curb Weight load is within the specified GVWR.
STARTING AND OPERATING CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle.
STARTING AND OPERATING Gross Combination Weight Rating (GCWR) Trailer Tongue Weight (TW) The GCWR is the total permissible weight of your vehicle The TW is the downward force exerted on the hitch ball and trailer when weighed in combination. by the trailer. In most cases, it should not be less than 10% or more than 15% of the trailer load. You must consider NOTE: The GCWR rating includes a 150 lbs (68 kg) this as part of the load on your vehicle. allowance for the presence of a driver.
STARTING AND OPERATING Weight-Distributing Hitch A weight-distributing hitch system works by applying leverage through spring (load) bars. They are typically used for heavier loads, to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.
STARTING AND OPERATING Without Weight-Distributing Hitch (Incorrect) With Weight-Distributing Hitch (Correct)
STARTING AND OPERATING 327 The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the Trailer Towing Weights (Maximum Trailer Weight Ratings) chart for the Max. GTW towable for your given drivetrain.
STARTING AND OPERATING All trailer hitches should be professionally installed on your vehicle. Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine Model GCWR (Gross Combined Wt. Rating) 3.7L 4x2 8,700 lbs (3 946 kg) 3.7L 4x4 5.7L 4x2 5.7L 4x4 Frontal Area Max. GTW (Gross Trailer Wt.) 40 sq ft 3,500 lbs (1 (3.72 sq m) 8,800 lbs (3 991 kg) 40 sq ft 3,500 lbs (1 (3.
STARTING AND OPERATING 329 NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the Tire and Loading Information placard. Refer to the “Tire– Safety Information” section in this manual. Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information placard in the “Tire—Safety Information” section of this manual for the maximum combined weight of occupants and cargo for your vehicle.
STARTING AND OPERATING 331 • When hauling cargo or towing a trailer, do not over- • Total weight must be distributed between the tow load your vehicle or trailer. Overloading can cause a vehicle and the trailer such that the following four loss of control, poor performance or damage to brakes, ratings are not exceeded: axle, engine, transmission, steering, suspension, chas1. GVWR sis structure or tires. 2. GTW • Safety chains must always be used between your vehicle and trailer.
STARTING AND OPERATING − Check the trailer tires for proper tire inflation pres- − An electronically-actuated trailer brake controller is sures before trailer usage. required when towing a trailer with electronicallyactuated brakes. When towing a trailer equipped with − Check for signs of tire wear or visible tire damage a hydraulic surge-actuated brake system, an electronic before towing a trailer. Refer to “Tires–General Inforbrake controller is not required. mation” in this section.
STARTING AND OPERATING WARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • Towing any trailer will increase your stopping distance. When towing, you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result in an accident.
STARTING AND OPERATING Four-Pin Connector 1 — Female Pins 2 — Male Pin 3 — Ground 4 — Park 5 — Left Stop/Turn 6 — Right Stop/Turn Seven-Pin Connector 1 2 3 4 — — — — Battery Backup Lamps Right Stop/Turn Electric Brakes 5 — Ground 6 — Left Stop/Turn 7 — Running Lamps
STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. 335 The transmission fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation. Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals. Automatic Transmission The DRIVE range can be selected when towing.
STARTING AND OPERATING Cooling System To reduce potential for engine and transmission overheating, take the following actions: − City Driving When stopped for short periods of time, shift the transmission into NEUTRAL and increase engine idle speed. WARNING! Do not add a snow plow, winches, or any other aftermarket equipment to the front of your vehicle. This could adversely affect the functioning of the airbag system and you could be injured. − Highway Driving Reduce speed.
STARTING AND OPERATING Towing — Quadra-Trac I姞 (Single-Speed Transfer Case) Four-Wheel Drive Models Recreational towing is not allowed. This model does not have a NEUTRAL position in the transfer case. Towing — Quadra–Trac II姞 /Quadra–Drive姞 II Four-Wheel Drive Models CAUTION! Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing.
STARTING AND OPERATING complete. A “4WD SYSTEM IN NEUTRAL” message will 5. Start the engine. display on the EVIC (Electronic Vehicle Information 6. Shift the transmission into DRIVE. Center). Refer to “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. 7. Release the brake pedal and ensure that there is no vehicle movement. 8. Shut the engine off. 9. Shift the transmission into PARK. 10. Place the ignition key in the OFF position, and remove key. 11. Apply the parking brake.
STARTING AND OPERATING CAUTION! Transmission damage may occur if the transmission is shifted into PARK with the transfer case in NEUTRAL and the engine running. With the transfer case in NEUTRAL ensure that the engine is OFF prior to shifting the transmission into PARK (refer to steps 7 and 8 above). 339 2. Turn the ignition key ON, engine off. 3. Shift the transmission into NEUTRAL. 4. Shift the transfer case out of NEUTRAL. Hold down the NEUTRAL “pin” switch (with a pen, etc.
STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL position without first fully engaging the parking brake. The transfer case NEUTRAL position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move even if the transmission is in PARK. The parking brake should always be applied when the driver is not in the vehicle. Neutral Switch 5. Shift the transmission into PARK. 6.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flashers . . . . . . . . . . . . . . . . 342 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . 346 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 342 䡵 Jump-Starting . . . . . . . . . . . . . . . . . . . . . . . . 351 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 343 䡵 Emergency Tow Hooks — If Equipped . . . . . . 353 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . 344 䡵 Towing A Disabled Vehicle . .
WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the switch bank just above the climate controls. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional • On the highways — Slow down.
WHAT TO DO IN EMERGENCIES 343 NOTE: There are steps that you can take to slow down JACKING AND TIRE CHANGING an impending overheat condition: • If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat. • You can also turn the Temperature Control to maximum heat, the Mode Control to floor and the Blower Control to high.
WHAT TO DO IN EMERGENCIES Jack Location The scissor-type jack and tire changing tools are located in a compartment behind the third row seat. Refer to “Cargo Area Features” in Section 3 for further information. Spare Tire Stowage The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive” nut.
WHAT TO DO IN EMERGENCIES 345 CAUTION! The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. When the spare is clear, tilt the retainer at the end of the cable and pull it through the center of the wheel. Preparations For Jacking Lowering/Raising Spare Tire Spare Tire Removal Fit the jack handle extension over the drive nut.
WHAT TO DO IN EMERGENCIES WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel. 2. Set the parking brake. 3. Place the shift lever into PARK 4. Turn OFF the ignition. 5. Turn on the Hazard Warning flasher. 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel.
WHAT TO DO IN EMERGENCIES 347 WARNING! (Continued) • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic.
WHAT TO DO IN EMERGENCIES Assembling Jack Tools Front Jacking Location For the rear axle, place it under the axle near the wheel to be changed. Ensure the jack is closest to the inside of the wheel when jacking on the rear axle. Do not raise the 4. Locate the jack as shown. For the front axle, place it vehicle until you are sure the jack is fully engaged. under the front lower control arm. Do not raise the vehicle until you are sure the jack is fully engaged.
WHAT TO DO IN EMERGENCIES 349 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. Rear Jacking Location 7. Position the spare wheel/tire on the vehicle and install the lug nuts with the cone-shaped end toward the wheel. Lightly tighten the nuts.
WHAT TO DO IN EMERGENCIES 9. Finish tightening the lug nuts. Push down on the wrench while tightening for increased leverage. Alternate nuts until each nut has been tightened twice. The correct wheel nut tightness is 95 ft lbs (130 N·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10. Lower the jack to it’s fully closed position.
WHAT TO DO IN EMERGENCIES JUMP-STARTING If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly, so follow this procedure carefully. WARNING! • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. You could be seriously injured.
WHAT TO DO IN EMERGENCIES 3. Turn off the heater, radio and all unnecessary electrical loads. 4. Connect one end of a jumper cable to the positive terminal of the booster battery. Connect the other end of the same cable to the positive terminal of the discharged battery. WARNING! • Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. • Do not connect the cable to the negative post of the discharged battery.
WHAT TO DO IN EMERGENCIES WARNING! Any procedure other than above could result in: • Personal injury caused by electrolyte squirting out the battery vent. • Personal injury or property damage due to battery explosion. CAUTION! Any procedure other than above could result in damage to the charging system of the booster vehicle or of the immobilized vehicle. EMERGENCY TOW HOOKS — IF EQUIPPED If your vehicle is equipped with tow hooks, there will be one in the rear and two mounted on the front of the vehicle.
WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE 2–Wheel Drive Models Only Provided the transmission is operable, tow only in NEUTRAL at speeds not exceeding 30 mph (48 km/h), for distances of not more than 15 miles (24 km). CAUTION! Towing at more than 30 mph (48 km/h) or for more than 15 miles (24 km), can cause severe transmission damage.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment – 3.7L . . . . . . . . . . . . . . 357 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 363 䡵 Engine Compartment – 5.7L . . . . . . . . . . . . . . 358 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 366 䡵 Onboard Diagnostic System – OBD II . . . . . . . 359 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . 366 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 359 ▫ Maintenance-Free Battery . . . . . . . .
MAINTAINING YOUR VEHICLE ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 374 䡵 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . 400 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 379 䡵 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . 400 ▫ Front/Rear Axle Fluid . . . . . . . . . . . . . . . . . 381 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 401 ▫ Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 382 ▫ Head Lamp . . . . .
MAINTAINING YOUR VEHICLE 357 ENGINE COMPARTMENT – 3.
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT – 5.
MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM – OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE The message will remain displayed until the vehicle diagnostic system can retest the fuel system. The test will perform the next time the vehicle is started, if the vehicle was keyed off above 40°F (4°C) outside temperature and the following vehicle start is above 40°F (4°C) outside temperature. It may be possible to have a message that will not clear due to the test being disabled due to low outside temperatures.
MAINTAINING YOUR VEHICLE 2. Turn the ignition to the ON position, but do not crank or start the engine. 3. If you crank or start the engine, you will have to start this test over. 361 b. The MIL will not flash at all and will remain fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is ready and you can proceed to the I/M station. If your OBD II system is not ready, you should see your 4.
MAINTAINING YOUR VEHICLE REPLACEMENT PARTS Use of genuine MOPAR威 parts for normal/scheduled maintenance and repairs is highly recommended to ensure the designed performance. Damage or failures caused by the use of non-MOPAR威 parts for maintenance and repairs will not be covered by the manufacturer’s warranty. DEALER SERVICE Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner.
MAINTAINING YOUR VEHICLE CAUTION! • Failure to properly maintain your vehicle or perform repairs and service when necessary could result in more costly repairs, damage to other components or negatively impact vehicle performance. Immediately have potential malfunctions examined by an authorized Chrysler Group LLC dealership or qualified repair center. • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals.
MAINTAINING YOUR VEHICLE CAUTION! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. manufacturer recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE Engine Oil Viscosity SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. 365 Synthetic Engine Oils You may use synthetic engine oils if the recommended oil quality requirements are met, and the recommended maintenance intervals for oil and filter changes are followed. The engine oil filler cap also shows the recommended engine oil viscosity for your vehicle.
MAINTAINING YOUR VEHICLE environment. Contact your local authorized dealer, service station, or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced with a new filter at every oil change. WARNING! The air induction system (air cleaner, hoses, etc) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.
MAINTAINING YOUR VEHICLE Maintenance-Free Battery Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic maintenance required. 367 WARNING! (Continued) • Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling. WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin or clothing.
MAINTAINING YOUR VEHICLE Air Conditioner Maintenance For best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt condition should also be checked at this time. CAUTION! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components.
MAINTAINING YOUR VEHICLE 369 NOTE: Use only manufacturer approved A/C System wear. Prior to the application of any lubricant, the parts Sealers, Stop Leak Products, Seal Conditioners, Compres- concerned should be wiped clean to remove dust and grit; after lubricating excess oil and grease should be sor Oil, and Refrigerants. removed. Particular attention should also be given to Refrigerant Recovery and Recycling hood latching components to insure proper function.
MAINTAINING YOUR VEHICLE Operation of the wipers on dry glass for long periods windshield will light on the vehicle graphic outline and may cause deterioration of the wiper blades. Always use the “WASHER FLUID LOW” message will be displayed. washer fluid when using the wipers to remove salt or dirt The fluid reservoir for the windshield washers and the from a dry windshield. rear window washer is shared.
MAINTAINING YOUR VEHICLE WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
MAINTAINING YOUR VEHICLE CAUTION! CAUTION! The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions control device and may seriously reduce engine performance and cause serious damage to the engine. Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition.
MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your exhaust system can contact anything that can burn. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating.
MAINTAINING YOUR VEHICLE Cooling System WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot. Engine Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable).
MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old engine coolant (antifreeze). Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals.
MAINTAINING YOUR VEHICLE CAUTION! (Continued) • This vehicle has not been designed for use with Propylene Glycol-based engine coolant (antifreeze). Use of Propylene Glycol-based engine coolant (antifreeze) is not recommended. When adding engine coolant (antifreeze): • The manufacturer recommends using MOPAR威 Antifreeze/ Coolant 5–Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent.
MAINTAINING YOUR VEHICLE Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent engine coolant (antifreeze) changes.
MAINTAINING YOUR VEHICLE rules for your community. To prevent ingestion by animals and children, do not store ethylene glycol-based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. Coolant Level The coolant bottle provides a quick visual method for determining that the engine coolant (antifreeze) level is adequate.
MAINTAINING YOUR VEHICLE 379 • Do not overfill the coolant recovery bottle. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the • Check the engine coolant (antifreeze) freeze point in condenser clean, also. the radiator and in the coolant recovery bottle. If engine coolant (antifreeze) needs to be added, contents • Do not change the thermostat for Summer or Winter operation.
MAINTAINING YOUR VEHICLE WARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency.
MAINTAINING YOUR VEHICLE 381 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a accident.
MAINTAINING YOUR VEHICLE Selection of Lubricant Use only the manufacturer’s recommended fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. Transfer Case Drain First remove fill plug, then remove drain plug. Recommended tightening torque for drain and fill plugs is 15 to 25 ft lbs (20 to 34 N·m). CAUTION! Fluid Level Check When installing plugs, do not overtighten. You could Inspect the transfer case for fluid leaks.
MAINTAINING YOUR VEHICLE Automatic Transmission Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission performance. Use only the manufacturer’s recommended transmission fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. It is important that the transmission fluid be maintained at the prescribed level using the recommended fluid.
MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Do not use chemical flushes in your transmission as the chemicals can damage your transmission components. Such damage is not covered by the New Vehicle Limited Warranty. • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder.
MAINTAINING YOUR VEHICLE 385 6. Remove the dipstick again, and note the fluid level on both sides. The fluid level should be between the “HOT” (upper) reference holes on the dipstick at normal operating temperature. The fluid level is only valid if there is a solid coating of oil on both sides of the dipstick. If the fluid is low, add as required into the dipstick tube. Do To check the fluid level properly, the following procedure not overfill.
MAINTAINING YOUR VEHICLE CAUTION! Be aware that if the fluid temperature is below 50°F (10°C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake. To prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated.
MAINTAINING YOUR VEHICLE CAUTION! Under frequent heavy-duty driving conditions, change all lubricants, and lubricate body components, all driveline joints and steering linkage more often than in normal service, to prevent excessive wear. 387 What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact.
MAINTAINING YOUR VEHICLE • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover or equivalent to remove. CAUTION! (Continued) • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals. • Use a high quality cleaner wax, such as MOPAR威 Cleaner Wax to remove road film, stains, and to protect your paint finish. Take care never to scratch the Special Care paint.
MAINTAINING YOUR VEHICLE 389 • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. mild soap and water to prevent corrosion. To remove heavy soil, use MOPAR威 Wheel Cleaner or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush or metal polishes.
MAINTAINING YOUR VEHICLE • For tough stains, apply MOPAR威 Total Clean or a mild if absolutely necessary. Do not use harsh cleaners or soap solution to a clean, damp cloth and remove the Armor All威. Use MOPAR威 Total Clean or equivalent to stain. Use a fresh, damp towel to remove soap residue. clean vinyl upholstery.
MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas, they may cause respiratory harm. 391 Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters.
MAINTAINING YOUR VEHICLE 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use MOPAR威 Total Clean, a mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly. Fuse Panel Dry with a soft tissue.
MAINTAINING YOUR VEHICLE Cavity 3 4 5 6 7 8 9 Cartridge Mini-Fuse Fuse 10 Amp Red 20 Amp Yellow 10 Amp Red Spare (B+) 20 Amp Yellow Spare (B+) 20 Amp Yellow Description Htd Mirror (EBL) Cavity 10 Rr Pwr Out (B+) Rr HVAC (R/O) (Commander Only) Door Locks (B+) Pwr Outlet (B+) 11 12 13 393 Cartridge Mini-Fuse Description Fuse 10 Amp Final Drive Control Red Module (FDCM), Heater Ventilation/ Air Conditioning (HVAC), Rear Heated Seat Switch, O/H, Heater Ventilation/ Air Conditioning (HVAC) Relay, Rear
MAINTAINING YOUR VEHICLE Cavity 14 15 16 17 19 20 Cartridge Mini-Fuse Fuse 20 Amp Yellow 10 Amp Red 10 Amp Red 15 Amp Blue Spare (R/S) 10 Amp Red Description Cigar Ltr (R/A) Tire Pressure Transponders (R/O) Upper & Lower Switch Bank, Diag.
MAINTAINING YOUR VEHICLE Underhood Fuses (Power Distribution Center) Power Distribution Center Cav- Cartridge Mini-Fuse Description ity Fuse 1 50 Amp PTC Heater 1 (Diesel Red Only) 395 Cav- Cartridge Mini-Fuse Description ity Fuse 2 40 Amp HID Headlamps Green 3 50 Amp PTC Heater 2 (Diesel Red Only) 4 30 Amp Power Outlets Pink 5 50 Amp PTC Heater 3 (Diesel Red Only) 6 30 Amp Cig Lighter, Trail Tow Pink Batt 7 40 Amp Power Liftgate (ComGreen mander Only) 8 40 Amp Starter, JB Power Green 9 20 Amp Front Po
MAINTAINING YOUR VEHICLE Cav- Cartridge Mini-Fuse Description ity Fuse 10 — Spare 11 40 Amp HVAC Blower Green 12 30 Amp Rear Wiper, Ign R/O Pink 13 40 Amp Rear Window DeGreen froster (EBL)/Heated Mirror 14 30 Amp Rear HVAC (If Pink Equipped) 15 — Spare 16 50 Amp ASD Red 17 30 Amp ABS Pump Pink Cav- Cartridge Mini-Fuse Description ity Fuse 18 40 Amp Accessory Delay, Seats Green 19 40 Amp JB Power Green 20 30 Amp Wiper Motor Pink 21 20 Amp Fuel Pump Yellow 22 20 Amp TCM, A/C Clutch Yellow 23 25 Amp Pow
MAINTAINING YOUR VEHICLE Cavity 26 27 28 29 30 31 32 33 Cartridge Mini-Fuse Description Fuse 15 Amp Brake Lamps Blue 20 Amp HD Washer (If Yellow Equipped) (Export Only) 30 Amp ABS Valves Green 20 Amp PCM Batt (Gasoline Yellow Only) — Spare — Spare 15 Amp Powertrain Control Blue Module (Diesel Only) 20 Amp Final Drive Control Yellow Module (FDCM) E-Diff Cavity 34 35 36 37 38 39 40 41 42 Cartridge Mini-Fuse Fuse — 20 Amp Yellow — 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 25 Amp Natural 20 Amp Yellow —
MAINTAINING YOUR VEHICLE Cavity 43 44 Cartridge Mini-Fuse Description Fuse 25 Amp Coils, Actuators Natural — Spare Underhood Fuses (Integrated Power Module) Cavity 8 9 10 12 13 14 15 16 Integrated Power Module Cartridge Mini-Fuse Fuse 10 Amp Red 10 Amp Red 10 Amp Red 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow Description Lt Park Lamps Trailer-Tow Park Lamps Rt Park Lamps Front Control Module (FCM) Batt #4 Front Control Module (FCM) Batt #2 Adjustable Pedal Ft Fog Lamps
MAINTAINING YOUR VEHICLE Cavity 17 18 19 20 21 22 23 Cartridge Mini-Fuse Fuse 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 30 Amp Pink 50 Amp Red Description Rear Fog Lamps (Export Only) Front Control Module (FCM) Batt #1 Lt Trailer-Tow Stop/ Turn Front Control Module (FCM) Batt #3 Rt Trailer-Tow Stop/ Turn Final Drive Control Module (FDCM) MOD Radiator Fan Cavity 27 28 29 30 399 Cartridge Mini-Fuse Description Fuse 15 Amp Ignition Off Draw Blue (IOD) #1 — Intrusion Module,
MAINTAINING YOUR VEHICLE VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery. You may: REPLACEMENT BULBS Interior Lights Bulb Type Glove Box Lamp . . . . . . . . . . . . . . . . . . . . . . . . . 194 Grab Handle Lamp . . . . . . . . . . . . . . . . L002825W5W • Remove fuse #27 in the Intelligent Power Module Overhead Console Reading Lamps . . . . . . . . . VT4976 Rear Cargo Lamp . . . . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 401 NOTE: Numbers refer to commercial bulb types that can be purchased from your authorized dealer. If a bulb needs to be replaced, visit your authorized dealer or refer to the applicable Service Manual. BULB REPLACEMENT Head Lamp 1. Open the hood. 2. Disconnect the electrical connector. 3. Turn the low or high beam bulb 1/4 turn counterclockwise to unlock it from the housing. 1 — Low Beam Bulb 2 — High Beam Bulb 3 — Front Park/Turn Signal Bulb 4.
MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front Turn Signal 1. Turn the steering wheel all the way to the left or right. 2. Reach into the front wheel house ahead of the front wheel to unsnap and lift the cover over the access hole in the front of the wheel house splash shield. Access to the 3.
MAINTAINING YOUR VEHICLE 403 5. Pull the socket and bulb straight out from the opening in the housing. 6. Disconnect the electrical connector. 7. Pull the base of the bulb straight out of the socket. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 1 — Low Beam Bulb 2 — High Beam Bulb 3 — Front Park/Turn Signal Bulb 4.
MAINTAINING YOUR VEHICLE 2. Reach into the front wheel house ahead of the front 5. Turn the socket on the back of the housing 1/4 turn wheel to unsnap and lift the cover over the access hole in counterclockwise to unlock it. the front of the wheel house splash shield. Access to the 6. Pull the socket and bulb straight out from the opening bulb can be gained through the wheel liner hole. in the housing. 7. Pull the base of the bulb straight out of the socket.
MAINTAINING YOUR VEHICLE 405 4. Firmly grasp the appropriate bulb socket on the back of the rear lamp unit housing, and turn 1/4 turn counterclockwise to unlock it. 3. Pull the outboard side of the rear lamp unit rearward far enough to unsnap the two ball studs on the outboard side of the lamp housing from the two plastic grommets in the quarter outer panel. Pull the lamp unit rearward far enough away to access the bulbs.
MAINTAINING YOUR VEHICLE 5. Disconnect the electrical connector. 6. Pull the socket and bulb straight out from the opening in the housing. 7. Pull the base of the bulb straight out of the socket. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Center High Mounted Stop Lamp (CHMSL) 2. Twist the bulb socket to remove from the CHMSL housing. 1.
MAINTAINING YOUR VEHICLE 407 FLUIDS AND CAPACITIES Fuel (Approximate) Engine Oil with Filter 3.7 Liter Engine (SAE 5W-20, API Certified) 5.7 Liter Engine (SAE 5W-20, API Certified) Cooling System * 3.7L Engine (MOPAR威 Engine Coolant/Antifreeze 5 Year/100,000 Mile Formula or equivalent) — Without Rear Heat 3.7L Engine (MOPAR威 Engine Coolant/Antifreeze 5 Year/100,000 Mile Formula or equivalent) — With Rear Heat 5.
MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Spark Plugs (3.7L Engine) Spark Plugs (5.7L Engine) Fuel Selection (3.7L Engine) Fuel Selection (5.7L Engine) Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent. Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
MAINTAINING YOUR VEHICLE 409 Chassis Component Automatic Transmission Transfer Case (NV140 Single Speed Only) Transfer Case (NV245 Two Speed Only) Axle Differential (Front-Rear) Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid or equivalent. MOPAR威 ATF+4 Automatic Transmission Fluid or equivalent. MOPAR威 NV 247/245 Transfer Case Lubricant or equivalent.
M A I N T E N A N C ▫ Required Maintenance Intervals . . . . . . . . . . 414 E MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 412 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . .
M A I N T E N A N C E 412 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 413 M A • Change your engine oil more often if you drive your • Check the windshield washer solvent and add if I N vehicle off-road for an extended period of time. required. • Under no circumstances should oil change intervals Once a Month exceed 6,000 miles (10,000 km) or 6 months, whichever • Check tire pressure and look for unusual wear or comes first. damage.
M A I N T E N A N C E S C H E D U L E S 8 414 MAINTENANCE SCHEDULES At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.
MAINTENANCE SCHEDULES 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Repair Order # Signature Authorized Chrysler Dealer Date Dealer Code 415 M 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions.
M 416 MAINTENANCE SCHEDULES A I 18,000 Miles (30,000 km) or N T 18 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C ❏ Inspect the front and rear axle fluid, E S C H E D U L E S 8 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
MAINTENANCE SCHEDULES 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings, replace if necessary.
M 418 MAINTENANCE SCHEDULES A I 42,000 Miles (70,000 km) or N T 42 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary.
MAINTENANCE SCHEDULES 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
M 420 MAINTENANCE SCHEDULES A I 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule N ❏ Change the engine oil and engine oil filter. T E ❏ Rotate tires. N ❏ Replace the engine air cleaner filter. A ❏ Inspect the brake linings; replace if necessary. N ❏ Replace the ignition cables (3.7L Engine). C ❏ Replace the spark plugs (3.7L and 5.7L Engines). E ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes.
MAINTENANCE SCHEDULES 66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the CV joints. ❏ Inspect exhaust system.
M 422 MAINTENANCE SCHEDULES A I 78,000 Miles (130,000 km) or N T 78 Months Maintenance E Service Schedule N ❏ Change the engine oil and engine oil A filter. N ❏ Rotate tires. C E 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary.
MAINTENANCE SCHEDULES 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the spark plugs (3.7L and 5.7L Engines). Inspect and replace PCV valve if necessary. † Adjust parking brake on vehicles equipped with four-wheel disc brakes. Inspect the transfer case fluid.
M 424 MAINTENANCE SCHEDULES A I 96,000 Miles (160,000 km) or 96 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ Rotate tires. A ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the N engine air cleaner filter; replace if necessary. C ❏ Inspect the brake linings; replace if necessary. E ❏ Inspect the CV joints. S C H E D U L E S 8 ❏ Inspect exhaust system.
MAINTENANCE SCHEDULES 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the front and rear axle fluid, change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing.
M 426 MAINTENANCE SCHEDULES A I 120,000 Miles (200,000 km) or 120 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ Rotate tires. A ❏ Replace the engine air cleaner filter. N ❏ Replace the ignition cables (3.7L Engine). C ❏ Replace the spark plugs (3.7L and 5.7L Engines). E ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. S C H E D U L E S 8 ❏ ❏ ❏ ❏ Inspect the brake linings; replace if necessary. Inspect the CV joints.
MAINTENANCE SCHEDULES 132,000 Miles (220,000 km) or 132 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary.
M 428 MAINTENANCE SCHEDULES A I 144,000 Miles (240,000 km) or 144 Months Maintenance Service N T Schedule E ❏ Change the engine oil and engine oil filter. N ❏ Rotate tires. A ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the N engine air cleaner filter; replace if necessary. C ❏ Inspect the brake linings; replace if necessary.
MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 435 ▫ Prepare For The Appointment . . . . . . . . . . . 433 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 435 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 433 䡵 Warranty Information (U.S. Vehicles Only) . . . .
IF YOU NEED CONSUMER ASSISTANCE 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 439 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 439 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 439 ▫ Temperature Grades . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 433 the service advisor and list the items in order of priority. At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the for an appointment. right papers with you. Take your warranty folder. All work to be performed may not be covered by the IF YOU NEED ASSISTANCE warranty.
IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized • Vehicle delivery date and mileage dealer’s service manager first. Most matters can be reChrysler Group LLC Customer Center solved with this process. P.O. Box 21–8004 • If for some reason you are still not satisfied, talk to the Auburn Hills, MI 48321–8004 general manager or owner of the authorized dealer- Phone: (800) 992-1997 ship. They want to know if you need assistance. Chrysler Canada Inc.
IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE 437 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
IF YOU NEED CONSUMER ASSISTANCE NOTE: A street address is required when ordering • Diagnostic Procedure Manuals manuals (no P.O. Boxes). Diagnostic Procedure Manuals are filled with dia• Service Manuals grams, charts and detailed illustrations. These practical manuals make it easy for students and technicians These comprehensive Service Manuals provide the to find and fix problems on computer-controlled veinformation that students and professional technicians hicle systems and features.
IF YOU NEED CONSUMER ASSISTANCE Call toll free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the Worldwide Web at: • www.techauthority.com DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES The following tire grading categories were established by the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in each category is shown on the sidewall of the tires on your vehicle.
IF YOU NEED CONSUMER ASSISTANCE WARNING! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel.
INDEX 10
INDEX ABS (Anti-Lock Brake System) . . . . . . . . . . . . . . 269 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . . 117 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 366 Air Conditioner Maintenance . . . . . . . . . . . . . . . 368 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 226 Air Conditioning, Operating Tips . . . . . . . . . . . . 235 Air Conditioning, Rear Zone . . . . . . . . . . .
INDEX 443 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 380 383 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267 383 Warning Light . . . . . . . . . . . . . . . . . . . . . . . . 160 254 250 Brake/Transmission Interlock . . . . . . . . . . . . . . . 247 140 Break-In Recommendations, New Vehicle . . . . . . . . 73 140 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 400,401 Bulbs, Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Battery . . . .
INDEX Cargo Load Floor . . . . . . . . . . . . . . . . . . . . . . . . 147 Cargo (Vehicle Loading) . . . . . . . . . . . . . . . . . . . 320 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . 85,223 Center High Mounted Stop Light . . . . . . . . . . . . 406 Certification Label . . . . . . . . . . . . . . . . . . . . . . . 320 Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301 Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . 343 Chart, Tire Sizing . . . .
INDEX 445 Disposal Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 Used Engine Fluids . . . . . . . . . . . . . . . . . . . . 365 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . 29 Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 130 Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 Off-Pavement . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Electronic Roll Mitigation (ERM) . . . . . . . . . . . . . 274 Electronic Speed Control (Cruise Control) . . . . . . . 119 Electronic Stability Program (ESP) . . . . . . . . . . . . 275 Electronic Throttle Control Warning Light . . . . . . 169 Electronic Vehicle Information Center (EVIC) . 167,170 Emergency, In Case of Freeing Vehicle When Stuck . . . . . . . . . . . . . . . 255 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 342 Jacking . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 447 Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380 Exhaust Gas Caution . . . . . . . . . . . . . . 38,74,317,371 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 Exhaust System . . . . . . . . . . . . . . . . . . . . . . . 74,371 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 266 Extender, Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . 48 Exterior Finish Care . . . . . . . . . . . . . . . . . . . . . .
INDEX Gasoline . . . . . . Gauge . . . . . . . . Materials Added . Octane Rating . . Requirements . . . Saver Mode . . . . Tank Capacity . . Fuel Optimizer . . . Fuel Saver . . . . . . . Fuel System Caution Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . 90,91 Heater, Engine Block . . . . . . . . . . . . . . . . . . . . . 245 High Beam Indicator . . . . . . . . . . . . . . . . . . . . . 161 High Beam/Low Beam Select (Dimmer) Switch . . 111 Hill Descent Control . . . . . . . . . . . . . . . . . . . . . 283 Hill Start Assist . . . . . . . . . . . . . . . . . . . . . . . . . 280 Hitches Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 327 Holder, Cup . . . . . . . . . . . . .
INDEX Key, Sentry (Immobilizer) Key-In Reminder . . . . . . Keyless Entry System . . . Keys . . . . . . . . . . . . . . Knee Bolster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 17 21 14 50 Lane Change Assist . . . . . . . . . . . . . . . . . . . . . . 111 Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . .
INDEX Headlight Switch . . . . . . . . . . . . . . . . . . . . . . 105 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . 401 Headlights On With Wipers . . . . . . . . . . . . . . . 106 High Beam Indicator . . . . . . . . . . . . . . . . . . . . 161 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . 20 Instrument Cluster . . . . . . . . . . . . . . . . . . 105,109 Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . 109,111 Lights On Reminder . . . . . . . . . . . . . .
INDEX Vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Luggage Rack (Roof Rack) . . . . . . . . . . . . . . . . . 150 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . . . 87 Mode Fuel Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 Maintenance Free Battery . . . . . . . . . . . . . . . . . . 367 Modifications/Alterations, Vehicle . . . . . . . . . . . . . 9 Maintenance Procedures . . . . . . . . . . . . . . . . . . .
INDEX Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407 Change Interval . . . . . . . . . . . . . . . . . . . . . . . 364 Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Lift Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Outlet (Auxiliary Electrical Outlet) . . . . . . . . . . 140 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . 265,266 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Windows . . .
INDEX Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . 315 Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369 Reminder, Lights On . . . . . . . . . . . . . . . . . . . . . 110 Reminder, Seat Belt . . . . . . . . . . . . . . . . . . . . . . . 47 Remote Control Starting System . . . . . . . . . . . . . . . . . . . . . . . . 26 Remote Keyless Entry (RKE) . . . . . . . . . . . . . . . . . 21 Remote Sound System (Radio) Controls . . . . . . . . 220 Remote Starting System . . .
INDEX Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 Shoulder Belt Anchorage . . . . . . . . . . . . . . . . . 44 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390 Easy Entry . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Snow Plow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . 297,344 Specifications Fuel (Gasoline) . . . . . . . . . . . . . . . . . . . . . . . . 314 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364 Speed Control (Cruise Control) . . . . . . . . . . . . . . 119 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX Tire Identification Number (TIN) . . . . . . . . . . . . . 289 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . 286 Tire Safety Information . . . . . . . . . . . . . . . . . . . . 286 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76,294,439 Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . 295 Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301 Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343 Compact Spare . .
INDEX Cooling System Tips . . . . . . . . . . . . . . . . . . . . 336 Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 Minimum Requirements . . . . . . . . . . . . . . . . . 330 Trailer and Tongue Weight . . . . . . . . . . . . . . . 329 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 Trailer Towing Guide . . . . . . . . . . . . . . . . . . . . . 328 Trailer Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 328 Transfer Case . . . . . . . . . . . . . . .
INDEX Voice Recognition System (VR) . . . . . . . . . . . . . . . 85 Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 33,139 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . 235 Warning Flasher, Hazard . . . . . . . . . . . . . . . . . . 342 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Warning, Roll Over . . . . . . . . . . . . . . . . . . . . . . . . 5 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Warnings and Cautions . . .
