2009 LIBERTY LIBERTY 2009 owner’s manual Chrysler LLC 81-326-0941 Second Edition Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 CONTENTS 䡵 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Warnings And Cautions . . . . . . . . . . . . . . . . . . . 7 䡵 Rollover Warning . . . . . . . . . . . . . . . . . . . . . . . 4 䡵 Vehicle Identification Number 䡵 How To Use This Manual . . . . . . . . . . . . . . . . . . 5 䡵 Vehicle Modifications/Alterations . . . . . . . . . . . . 8 ..............
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your vehicle. It is supplemented by a Warranty Information Booklet and various customer-oriented documents. You are urged to read these publications carefully. Following the instructions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
INTRODUCTION 5 million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. HOW TO USE THIS MANUAL Consult the Table of Contents to determine which section contains the information you desire. The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects. Rollover Warning Label Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury.
6 INTRODUCTION
INTRODUCTION 7 WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information. Observe all Warnings and Cautions. VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A Word About Your Keys . . . . . . . . . . . . . . . . . 12 ▫ To Arm The System . . . . . . . . . . . . . . . . . . . 18 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . 12 ▫ To Disarm The System . . . . . . . . . . . . . . . . . 19 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . 14 䡵 Illuminated Entry System . . . . . . . . . . . . . . . . . 19 䡵 Sentry Key威 . . . . . . . . . . . . . . . . . . . . . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . 24 ▫ Programming Additional Transmitters . . . . . . 25 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 39 䡵 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 ▫ Battery Replacement . . . . . . . . . . . . . . . . . . . 25 ▫ Liftgate Flipper Glass . . . . . . . . . . . . . . . . . . 41 ▫ General Information . . . . . . . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Driver And Front Passenger Supplemental Restraint System (SRS) - Airbags . . . . . . . . . . 53 ▫ Child Restraint . . . . . . . . . . . . . . . . . . . . . . . 71 䡵 Engine Break-In Recommendations . . . . . . . . . . 80 䡵 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 ▫ Transporting Passengers . . . . . . . . . . . . . . . . 81 ▫ Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS You can insert the double-sided keys into the locks with either side up. The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer. Ask your authorized dealer for these numbers and keep them in a safe place. Ignition Key Removal Automatic Transmission Place the shift lever in PARK.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 (if equipped), and power outlets will remain active for 45 seconds after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle. CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition, and lock all doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 NOTE: A key that has not been programmed is also considered an invalid key, even if it is cut to fit the ignition switch lock cylinder for that vehicle. During normal operation, after turning on the ignition switch, the Vehicle Security Light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Replacement Keys NOTE: Only keys that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a Sentry Key威 is programmed to a vehicle, it cannot be programmed to any other vehicle. CAUTION! Always remove the Sentry Keys威 from the vehicle and lock all doors when leaving the vehicle unattended. At the time of purchase, the original owner is provided with a four-digit Personal Identification Number (PIN).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 3. Insert the second valid key into the ignition switch. Turn the ignition switch to the ON position within 15 seconds. After 10 seconds, a chime will sound. In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch to the LOCK position and remove the second key. NOTE: If a programmed key is lost, see your authorized dealer to have all remaining keys erased from the system’s memory.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE VEHICLE SECURITY ALARM — IF EQUIPPED The Vehicle Security Alarm monitors the vehicle doors, liftgate, and liftgate flip-up window for unauthorized entry and ignition for unauthorized operation. If something triggers the alarm, the Vehicle Security Alarm will sound the horn intermittently, flash the headlights and taillights, and flash the Vehicle Security Light in the instrument cluster. NOTE: The Panic and Security alarms are quite different.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 cancel the arming process. If the Vehicle Security Alarm arms successfully, the Vehicle Security Light will flash at a slower rate to indicate the alarm is set. NOTE: For added security, whenever the Security Alarm is armed, the HomeLink威/Garage Door Opener (if equipped) is disabled as well.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE under “Personal Settings (Customer-Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4. The interior lights will fade to off after approximately 30 seconds or they will immediately fade to off once the ignition switch is turned ON. the line of transmission must not be blocked with metal objects when using the RKE transmitter. NOTE: Inserting the key into the ignition switch disables all buttons on the RKE transmitter.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 To Unlock the Doors and Liftgate Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door or twice to unlock all doors and the liftgate. The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Illuminated Approach — If Equipped This feature activates the headlights for up to 90 seconds when the doors are unlocked with the RKE transmitter. The time for this feature is programmable on vehicles equipped with the Electronic Vehicle Information Center (EVIC). For details, refer to “Illumination Approach,” under “Personal Settings (Customer-Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 3. Test the feature from outside the vehicle by pressing the LOCK button on the RKE transmitter. (Customer-Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4. 4. Repeat these steps if you want to return this feature to its previous setting.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the RKE transmitter while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. To Unlatch the Liftgate Flip-Up Window Press the REAR RELEASE button twice to unlatch the liftgate flip-up window. WARNING! To avoid injury stand back when opening. Glass will automatically rise.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 The PANIC Alarm will stay on for three minutes unless you turn it off by pressing the PANIC button a second time or if the vehicle speed is 5 mph (8 km/h) or greater. During the PANIC Mode, the door locks and Remote Keyless Entry (RKE) system will function normally. PANIC mode will not disarm the Security System on vehicles so equipped.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. With the RKE transmitter buttons facing down, use a flat blade tool to pry the two halves of the RKE transmitter case apart. Make sure not to damage the seal during removal. 3. Remove and replace the battery. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 4. To reassemble the RKE transmitter case, snap the two halves together. 5.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. How To Use Remote Start All of the following conditions must be met before the engine will remote start: If your RKE transmitter fails to operate from a normal distance, check for these two conditions: • Shift lever in PARK. 1. Weak battery in RKE transmitter.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Enter Remote Start Mode Press and release the REMOTE START button on the RKE transmitter twice, within five seconds. The parking lights will flash and the horn will chirp twice (if programmed). Then, the engine will start and the vehicle will remain in the Remote Start mode for a 15-minute cycle. NOTE: • For security, power window operation and sunroof or Sky Slider威 operation (if equipped) is disabled when the vehicle is in the Remote Start mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 DOOR LOCKS Manual Door Locks To lock each door, push the door lock plunger on each door trim panel downward. To unlock each door, pull the door lock plunger on each door trim panel upward. If the door lock plunger is down when you shut the door, the door will lock. Make sure the keys are not inside the vehicle before closing the door. NOTE: The manual door locks will not lock or unlock the liftgate.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the key in the ignition. A child could operate power windows, other controls, or move the vehicle. Power Door Locks A power door lock switch is located on each of the front door trim panels. Use this switch to lock or unlock the doors and liftgate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 If you press the power door LOCK switch while the key is in the ignition, and any front door is open, the power locks will not operate. This prevents you from accidentally locking your keys in the vehicle. Removing the key or closing the door will allow the locks to operate. A chime will sound if the key is in the ignition switch and a door is open, as a reminder to remove the key.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Press the power door LOCK switch to lock the doors. 4. The driver door is opened. 4. A single chime will indicate the completion of the programming. 5. The doors were not previously unlocked. 5. Repeat these steps if you want to return this feature to its previous setting. NOTE: Use the Automatic Door Locks feature in accordance with local laws. 6. The vehicle speed is 0 mph (0 km/h).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 3. Press the power door UNLOCK switch to unlock the doors. 4. A single chime will indicate the completion of the programming. 2 Repeat these steps if you want to return this feature to its previous setting. NOTE: Use the Automatic Unlock Doors On Exit feature in accordance with local laws.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! 2. Insert the tip of the ignition key into the child lock control and rotate it to the UNLOCK position. Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: • After engaging the Child Protection Door Lock system, always test the door from the inside to make certain it is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 WINDOWS Power Windows The window controls on the driver’s door trim panel control all the door windows. There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate when the ignition switch is in the ON or ACC position. WARNING! Never leave children in a vehicle, with the key in the ignition switch.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To open the window part way, press the window switch to the first detent and release it when you want the window to stop. (Customer-Programmable Features” in the “Electronic Vehicle Information Center (EVIC),” in Section 4 of this manual. To stop the window from going all the way down during the Auto-Down operation, pull up on the switch briefly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power window switches will remain active for 45 seconds after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature. NOTE: • If the window runs into any obstacle during autoclosure, it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch The window lockout switch on the driver’s door trim panel allows you to disable the window control on the other doors. To disable the window control on the other doors, press and release the window LOCK button (setting it in the down position). To enable the window controls, press and release the window LOCK button again (setting it in the up position).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Reset It may be necessary at some point in time to reactivate the Auto Up feature. To do so, perform the following procedure: 1. Pull the window switch up to close window completely and continue to hold the switch up for an additional two seconds after the window is closed. 2. Push the window switch down firmly to the second detent to open the window completely and continue to hold the switch down for an additional two seconds after the window is fully open.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE To open the liftgate, pull up (squeeze) on the handle and lift. NOTE: Use the power door LOCK switch on either front door trim panel or the Remote Keyless Entry (RKE) transmitter to lock and unlock the liftgate. The manual door locks on the doors and the driver’s door lock cylinder will not lock and unlock the liftgate. WARNING! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on the window switch located on the liftgate. WARNING! To avoid injury, stand back when opening. Glass may automatically rise. NOTE: If a malfunction to the liftgate latch should occur, an emergency liftgate latch release can be used to open the liftgate.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. These include the front and rear seat belts for the driver and all passengers, front airbags for both the driver and front passenger, and side curtain airbags for the driver and passengers seated next to a window. If you will be carrying children too small for adult-sized belts, your seat belts also can be used to hold infant and child restraint systems.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 inside of the vehicle. Everyone in a motor vehicle should be belted at all times to reduce or prevent injuries. Lap/Shoulder Belts All seating positions in your vehicle have combination lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move freely with you under normal conditions.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! Latch Plate To Buckle • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop, you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! • A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. • A lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.). Removing Slack From Belt 6.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the shoulder belt anchorage to be adjusted in the upward position without pressing the release button. To verify the shoulder belt anchorage is latched, pull downward on the shoulder belt anchorage until it is locked into position. As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you will prefer a higher position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Seat Belt Pretensioner — If Equipped The front passenger seat belt is equipped with a pretensioning device that is designed to remove any slack from the seat belt systems in the event of a collision. These devices improve the performance of the seat belt by assuring that the belt is tight around the occupant early in a collision. Pretensioners work for all size occupants, including those in child restraints.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE BeltAlert威 Programming BeltAlert威 can be enabled or disabled by your authorized dealer or by performing the following steps: NOTE: Chrysler LLC does not recommend deactivating BeltAlert威. 1. With all doors closed, and the ignition switch in any position except ON or START, buckle the driver’s seat belt. 2. Turn the ignition switch to the ON position, but do not start the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Automatic Locking Mode — If Equipped In this mode, the shoulder belt is automatically prelocked. However, the belt will still retract to remove any slack in the shoulder belt. When To Use The Automatic Locking Mode Use the Automatic Locking Mode anytime a child safety seat is installed in the rear outboard seating position. Children 12 years old and younger should be properly restrained in the rear seat whenever possible.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • The belt and retractor assembly must be replaced if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual. • Failure to replace the belt and retractor assembly could increase the risk of injury in collisions. Seat Belts and Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Driver and Front Passenger Supplemental Restraint System (SRS) - Airbags This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s airbag is mounted in the steering wheel. The passenger’s front airbag is mounted in the instrument panel, above the glove compartment. The words SRS AIRBAG are embossed on the airbag covers.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size. The front passenger airbag is also certified to the Federal regulations that define Occupant Classification (refer to information on Occupant Classification System in this section).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 WARNING! WARNING! (Continued) • Do not put anything on or around the front and side curtain airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are no longer functional. These protective covers for the airbag cushions are designed to open only when the airbags are inflating. • Do not stack luggage or other cargo up high enough to block the location of the side curtain airbag.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE trigger on the crash side of the vehicle in moderate-tosevere side collisions or on both sides of the vehicle in rollover collisions. In certain types of collisions, both the front and side airbags may be triggered. However, even in collisions where the airbags deploy, you need the seat belts to keep you in the right position for the airbags to protect you properly.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 If a child from 1 to 12 years old must ride in the front passenger seat because the vehicle is crowded, move the seat as far back as possible, and use the proper child restraint (refer to information on Child Restraint in this section). You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should use their lap and shoulder belts properly. 3.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: • Occupant Classification System (OCS) — Front Passenger Seat Only • Occupant Restraint Controller (ORC) − Occupant Classification Module (OCM) • Airbag Warning Light − Passenger Airbag Disable (PAD) Indicator Light • Driver Airbag − Weight Sensors • Front Passenger Airbag How the Airbag System Works • Side Curtain Airbags above Side Windows • The Occupant Restraint Controller (OR
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 The ORC also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or ON position. These include all of the items listed above except the Passenger Airbag Disable (PAD) Indicator Light, the instrument panel, and the steering wheel and column. If the key is in the LOCK position, in the ACC position, or not in the ignition, the airbags are not on and they will not inflate.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Children 12 years and younger should always ride buckled up in a rear seat in an appropriate child restraint. • The Passenger Airbag Disable (PAD) Indicator Light (an amber light located in the center of the instrument panel) tells the driver and front passenger when the front passenger airbag is turned off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 The “PAD Indicator Light” should not be illuminated when an adult passenger is properly seated in the front passenger seat. In this case, the airbag is ready to be inflated if a collision requiring an airbag occurs. For all other occupants, the “PAD Indicator Light” will be illuminated indicating that the front passenger airbag is turned off and it will not inflate.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE will cause the system to turn the airbag on. In this case, the OCS has classified the occupant of the seat as an adult. An adult occupant needs to sit in a normal position (with their feet on or near the floor) in order to be properly classified. Reclining the seat back too far may change how an occupant is classified by the OCS.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 lodged under the seat and interferes with operation of the weight sensors, a fault will occur which turns on both the “PAD Indicator Light” and the “Airbag Warning Light.” Once the lodged object is removed, the fault will be automatically cleared after a short period of time. driver’s front airbag gas is vented through the vent holes in the sides of the airbag. The passenger’s front airbag gas is vented through the vent holes in the sides of the airbag.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Side Impact SRS Side Curtain Airbags are designed to activate only in certain side collisions and rollover events. When the ORC detects a collision requiring the side curtain airbag to inflate, it signals the inflators on the crash side of the vehicle or both sides of the vehicle for a rollover event. A quantity of non-toxic gas is generated to inflate the side curtain airbag.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 WARNING! Unapproved modifications or service procedures to the front passenger seat assembly or its related components may inadvertently change the airbag deployment in case of a frontal crash. This could result in death or serious injury to the front seat passenger if the vehicle is involved in an accident. A modified vehicle may not comply with required Federal Motor Vehicle Safety Standards (FMVSS).
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE throat irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instructions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you. WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Maintaining Your Airbag System WARNING! (Continued) WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper passenger side of the instrument panel. Do not modify the front bumper or vehicle body structure.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Do not place or hang any items such as add-on video players on the front passenger seatback. The additional weight may cause the Occupant Classification System to be unable to classify the front seat passenger correctly. This could allow the passenger frontal airbag to inflate when it is not desired. • It is dangerous to try to repair any part of the airbag system yourself.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Event Data Recorder (EDR) In the event of an accident, your vehicle is designed to record up to five seconds of specific vehicle data parameters (see the following list) in an event data recorder prior to the moment of airbag deployment, or near deployment, and up to a quarter second of high-speed deceleration data during and/or after airbag deployment. EDR data are ONLY recorded if an airbag deploys, or nearly deploys, and are otherwise unavailable. NOTE: 1.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the U.S. government and various states. Data of a potentially sensitive nature, such as would identify a particular driver, vehicle, or crash, will be treated confidentially. Confidential data will not be disclosed by Chrysler LLC to any third party except when: • Airbag disable light status (if equipped) 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Child Restraint Everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years and younger should ride properly buckled up in a rear seat, if available.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants and Child Restraints • Safety experts recommend that children ride rearward-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). Two types of child restraints can be used rearward-facing: infant carriers and “convertible” child seats. • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who are still too small to fit the vehicle’s seat belts properly. If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seatback, they should use a belt-positioning booster seat. The child and beltpositioning booster seat are held in the vehicle by the lap/shoulder belt.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • A rearward- facing infant restraint should only be used in a rear seat. A rearward-facing infant restraint in the front seat may be struck by a deploying passenger airbag, which may cause severe or fatal injury to the infant. Here are some tips on getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 the child restraint using lower anchorages and upper tether straps from the child restraint to the vehicle structure. LATCH-compatible child restraint systems are now available. However, because the lower anchorages are to be introduced over a period of years, child restraint systems having attachments for those anchorages will continue to have features for installation using the vehicle’s seat belts.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the LATCH-Compatible Child Restraint System We urge you to carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap. Tether Strap Mounting Many, but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. 2 To attach a child restraint tether strap: Route the tether strap over the seatback and attach the hook to the tether anchor located on the back of the seat.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. Transporting Pets Airbags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication of difficulty. WARNING! (Continued) • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Exhaust Gas SAFETY TIPS Transporting Passengers NEVER TRANSPORT PASSENGERS IN THE CARGO AREA.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If it is necessary to sit in a parked vehicle with the engine running, adjust your heating or cooling controls to force outside air into the vehicle. Set the blower at high speed. If you are required to drive with the trunk/liftgate open, make sure that all windows are closed and the climate control BLOWER switch is set at high speed. DO NOT use the recirculation mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Airbag Warning Light The light should come on and remain on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light is not lit during starting, see your authorized dealer. If the light stays on, flickers, or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 3 䡵 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 䡵 uconnect威 phone — If Equipped . . . . . . . . . . . . 94 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 90 ▫ Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 96 ▫ Automatic Dimming Mirror — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 90 ▫ Phone Call Features . . . . . . . . . . . . . . . . . . 104 ▫ Outside Mirrors . . . . . . . .
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Voice Recognition (VR) System — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 122 ▫ 60/40 Split Folding Rear Seat With Fold-Flat Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 ▫ Voice Recognition (VR) System Operation . . . 122 䡵 Driver Memory Seat — If Equipped . . . . . . . . 136 ▫ Commands . . . . . . . . . . . . . . . . . . . . . . . . 124 ▫ Programming The Memory Feature . . . . . . . 136 ▫ Voice Training . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 ▫ Headlights With Wipers (Available With Auto Headlights Only) . . . . . . . . . . . . . . . . 143 ▫ Headlights With Wipers (Available With Auto Headlights Only) . . . . . . . . . . . . . . . . 152 ▫ Headlight Time Delay — If Equipped . . . . . . 144 ▫ Rain Sensing Wipers — If Equipped . . . . . . . 152 ▫ Daytime Running Lights (DRL) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 144 ▫ Windshield Washers . . . . . . . . . . . . . . . . .
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 Rear Park Assist System — If Equipped . . . . . . 158 䡵 Power Sunroof — If Equipped . . . . . . . . . . . . 171 ▫ System Usage Precautions . . . . . . . . . . . . . . 159 ▫ Opening Sunroof — Express . . . . . . . . . . . . 172 ▫ Enabling And Disabling The System . . . . . . . 161 ▫ Opening Sunroof — Manual Mode . . . . . . . . 172 ▫ System Operation . . . . . . . . . . . . . . . . . . . . 162 ▫ Closing Sunroof — Express . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 䡵 Sky Slider威 Full Length Open Roof . . . . . . . . . 174 䡵 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 ▫ Sky Slider威 Usage Precautions . . . . . . . . . . . 175 ▫ Front Storage Compartment . . . . . . . . . . . . . 185 ▫ Sky Slider威 Control . . . . . . . . . . . . . . . . . . . 177 ▫ Console Storage Compartment . . . . . . . . . . . 185 ▫ Opening The Sky Slider威 . . . . . . . . . . . . . . . 177 䡵 Cargo Area Features . . . . .
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicle). The mirror should be adjusted while set in the day position (toward the windshield).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic and a slight overlap of the view obtained from the inside mirror. NOTE: The passenger side convex outside mirror will give a much wider view to the rear, and especially of the lane next to your vehicle.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors The power mirror switch is located on driver’s door trim panel. Models with Express Window Feature Press and release the mirror select button marked L (left) or R (right) and then press one of the four arrow buttons to move the mirror in the direction the arrow is pointing. The selection will time out after 30 seconds of inactivity to guard against accidentally moving a mirror position following an adjustment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Refer to “Rear Window Features” in this section, for further information. 3 Illuminated Vanity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Unclip the visor from the center clip. 3. Pull the sun visor toward the inside rearview mirror to extend it. uconnect姞 phone — IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated uconnect威 phone. Refer to your “Navigation User’s Manual” for uconnect威 phone operating instructions for these radios. Radio sales code can be located on the lower right corner of the Radio faceplate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Bluetooth威 technology - the global standard that enables different electronic devices to connect to each other without wires or a docking station, so uconnect威 phone works no matter where you stow your cellular phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s uconnect威 phone. The uconnect威 phone allows up to seven cellular phones to be linked to the system.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The radio display will be used for visual prompts from the uconnect威 phone such as ⬙CELL⬙ or caller ID on certain radios. Operation Voice commands can be used to operate the uconnect威 phone and to navigate through the uconnect威 phone menu structure. Voice commands are required after most uconnect威 phone prompts. You will be prompted for a specific command and then guided through the available options.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 To activate the uconnect威 phone from idle, simply press the PHONE button and follow the audible prompts for directions. All uconnect威 phone sessions begin with a press of the PHONE button on the radio control head. Cancel Command At any prompt, after the beep, you can say ⬙Cancel⬙ and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked to give your cellular phone a priority level between one and seven, with one being the highest priority. You can pair up to seven cellular phones to your uconnect威 phone. However, at any given time, only one cellular phone can be in use, connected to your uconnect威 phone. The priority allows the uconnect威 phone to know which cellular phone to use if multiple cellular phones are in the vehicle at the same time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 or downloaded phonebook. To learn how to store a name in the phonebook, refer to ⬙Add Names to Your uconnect威 Phonebook,⬙ in the phonebook. • The uconnect威 system will confirm the name and then dial the corresponding phone number, which may appear in the display of certain radios. Add Names to Your uconnect威 Phonebook NOTE: Adding names to the uconnect威 phonebook is recommended when the vehicle is not in motion. • Press the PHONE button to begin.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phonebook Download – Automatic Phonebook Transfer From Cellular Phone If equipped and specifically supported by your phone, uconnect威 phone automatically downloads names (text names) and number entries from the cellular phone’s phonebook. Specific Bluetooth威 Phones with Phone Book Access Profile may support this feature. See uconnect威 website for supported phones.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Phonebook Download — Single Entry If equipped and supported by your phone, uconnect威 phone allows the user to download entries from their phone via Bluetooth威. To use this feature, press the PHONE button and say “Phonebook Download.” The system prompts, “Ready to accept “V” card entry via Bluetooth威…” The system is now ready to accept phonebook entries from your phone using the Bluetooth威 Object Exchange Profile (OBEX).
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, cellular, or pager) that you wish to edit. • When prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • After you enter the name, the uconnect威 phone will ask you which designation you wish to delete: home, work, cellular, pager, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted. • Automatic downloaded phonebook entries cannot be deleted or edited. Delete/Erase “All” uconnect威 Phonebook Entries • Press the PHONE button to begin.
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The uconnect威 phone will then prompt you as to the number designation you wish to call. • The selected number will be dialed. Phone Call Features The following features can be accessed through the uconnect威 phone if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the uconnect威 phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Making a Second Call While Current Call is in Progress To make a second call while you are currently on a call, press the VOICE RECOGNITION button and say ⬙Dial⬙ or ⬙Call⬙ followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to ⬙Toggling Between Calls⬙ in this section. To combine two calls, refer to ⬙Conference Call⬙ in this section.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Termination To end a call in progress, momentarily press the PHONE button. Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the far end, a call on hold may not become active automatically. This is cell phone-dependent. To bring the call back from hold, press and hold the PHONE button until you hear a single beep. Redial • Press the PHONE button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 uconnect姞 phone Features Language Selection To change the language that the uconnect威 phone is using: • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais. • Continue to follow the system prompts to complete the language selection. After selecting one of the languages, all prompts and voice commands will be in that language.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area. • If supported, this number may be programmable on some systems. To do this, press the PHONE button and say ‘Setup’, followed by ‘Emergency’. • The uconnect威 phone does slightly lower your chances of successfully making a phone call as to that for the cellular phone directly.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Paging To learn how to page, refer to ⬙Working with Automated Systems.⬙ Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the uconnect威 phone. Voice Mail Calling To learn how to access your voice mail, refer to ⬙Working with Automated Systems.
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE send the corresponding phone number associated with the phonebook entry, as tones over the phone. NOTE: • You may not hear all of the tones due to cellular phone network configurations. This is normal. • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the uconnect威 phone (while dialing via the cellular phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth威 cellular phone, the audio will be played through your vehicle’s audio system.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Advanced Phone Connectivity List Paired Cellular Phone Names Transfer Call to and from Cellular Phone The uconnect威 phone allows ongoing calls to be transferred from your cellular phone to the uconnect威 phone without terminating the call. To transfer an ongoing call from your uconnect威 phone paired cellular phone to the uconnect威 phone or vice versa, press the VOICE RECOGNITION button and say ⬙Transfer Call.⬙ • Press the PHONE button to begin.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Select Another Cellular Phone This feature allows you to select and start using another phone paired with the uconnect威 phone. • Press the PHONE button to begin. • After the ⬙Ready⬙ prompt and the following beep, say ⬙Setup Select Phone⬙ and follow the prompts. • You can also press the VOICE RECOGNITION button at any time while the list is being played, and then choose the phone that you wish to select.
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, the uconnect威 phone Voice Training feature may be used. To enter this training mode, follow one of the two following procedures: From outside the uconnect威 phone mode (e.g.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English, French, and Spanish accents, the system may not always work for some.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the uconnect威 phone.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 3
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 3
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all Voice Commands Alternate(s) Voice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Primary language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing phonebook previous record again redial Voice Commands Alternate(s) pairing phone book Voice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call uconnect威 Tutorial try again voice training work yes 3
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 When you press the VR button, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the VR button, listen for the beep, and say your command. Pressing the VR button while the system is speaking is known as “barging in.
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Commands The Voice Recognition (VR) system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the Volume 1. Start a dialogue by pressing the VR button. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Voice Recognition (VR) system is speaking.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Radio FM To switch to the FM band, say “FM” or “Radio FM”.
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo To switch to the voice recorder mode, say “Memo”. In this mode, you may say the following commands: • “New Memo” (to record a new memo) — During the recording, you may press the VR button to stop recording. You proceed by saying one of the following commands: − “Previous” (to play the previous memo) − “Delete” (to delete a memo) • “Delete All” (to delete all memos) System Setup To switch to system setup, say “Setup”.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 NOTE: Keep in mind that you have to press the VR button first and wait for the beep before speaking the “Barge In” commands. Voice Training For users experiencing difficulty with the system recognizing their voice commands or numbers, uconnect威 phone Voice Training feature may be used. SEATS Manual Front Seat Adjustments The manual seat adjustment bar is at the front of the seat, near the floor. 3 1.
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE desired. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked. Recliner Adjustment The recliner control is on the outboard side of the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seat — If Equipped The power seat switch is on the outboard side of the seat near the floor. to tilt the seat. For vehicles equipped with a power passenger seat, use this switch to move the seat forward and rearward. CAUTION! Do not place any article under any seat as it may cause damage to the seat or seat controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Head Restraints Head restraints can reduce the risk of whiplash injury in the event of a rear impact. Adjust the head restraints so that the upper edge is as high as practical. The head restraints have a locking button that must be pushed inward to lower the head restraint. However, the head restraints may be raised without pushing in the button.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped This feature heats both the front driver and passenger seats. The controls for the front heated seats are located on the instrument panel below the climate controls. Heated Seat Switches After turning the ignition ON, you can choose from High, Low, or Off heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for High, one for Low, and none for Off.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 NOTE: When a heat setting is selected, heat will be felt within two to five minutes. WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical condition must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • Be sure everyone in your vehicle is in a seat and using a seat belt properly. To Lower the Rear Seat 1. Locate the release strap on the lower outboard side of each rear seatback. 2. Pull the release strap (toward the front of the vehicle). Rear Seat Release Strap 3. Fold the rear seat completely forward. 4.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 To Raise the Rear Seat NOTE: If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. Recliner Adjustment The rear seatback also reclines for additional passenger comfort. Pull the release strap while sitting in the rear seat to recline the seatback. 3 1. If locked in the folded position, pull the release strap (toward the front of the vehicle). 2.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SEAT — IF EQUIPPED This feature allows the driver to store up to two different memory profiles, for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat and side mirrors, and a set of desired radio station presets. The memory switch is located on the instrument panel to the left of the steering column. The switch contains an (S) button to activate the memory save function.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 2. Adjust all memory profile settings to desired preferences (i.e., seat, side mirror, and radio station presets). 3. Press and release the SET (S) button on the memory switch, then press the side of the rocker switch labeled (1) within five seconds. The Electronic Vehicle Information Center (EVIC), if equipped, will display which memory position is being set. If desired, a second memory profile can be stored into memory as follows: 1. Turn the ignition ON. 2.
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Linking and Unlinking the Remote Keyless Entry Transmitter to Memory Your Remote Keyless Entry (RKE) transmitters can be programmed to recall one of two pre-programmed memory profiles with a press of the UNLOCK button on the RKE transmitter. To program your RKE transmitters, perform the following: 1. Remove the key from the ignition. 2. Select the desired memory profile 1 or 2. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 To recall the memory settings for driver one, press MEMORY button number 1 or the UNLOCK button on the RKE transmitter linked to memory position 1. The distance the driver seat moves depends on where you have the driver seat positioned when you remove the key from the ignition switch. To recall the memory setting for driver two, press MEMORY button number 2 or the UNLOCK button on the RKE transmitter linked to memory position 2.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Easy Entry/Easy Exit feature is disabled when the driver’s seat position is less than 0.9 in (23 mm) forward of the rear stop. At this position, there is no benefit to the driver by moving the seat for Easy Exit or Easy Entry. Each stored memory setting will have an associated Easy Entry and Easy Exit position. NOTE: The Easy Entry/Easy Exit feature can be turned on or off through the programmable features in the EVIC.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 3 Underhood Safety Latch Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the underside of the hood.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! To prevent possible damage: • Before closing hood, make sure the hood prop rod is fully seated into its storage retaining clips. • Do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage. • Never drive your vehicle unless the hood is fully closed, with both latches engaged.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Headlights and Parking Lights Turn the end of the multifunction lever to the first detent for parking light operation. Turn the end of the lever to the second detent for headlight operation. Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, turn the end of the multifunction lever to the AUTO position (third detent).
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature. If you turn the headlights, or parking lights, or ignition switch ON again, the system will cancel the delay. The Headlights with Wipers feature can be turned on or off through the Electronic Vehicle Information Center (EVIC) — if equipped.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 NOTE: The Daytime Running Lights will turn off automatically when the turn signal is in operation and turn on again when the turn signal is not operating. Lights-On Reminder If the headlights or parking lights are on after the ignition is turned to the LOCK position, a chime will sound to alert the driver when the driver’s door is opened.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Move the multifunction lever upward or downward and the corresponding turn signal indicator on the instrument panel will flash to show proper operation of the front and rear turn signal lights. Turn Signal Control You can signal a lane change by moving the multifunction lever upward or downward partially without moving beyond the detent. If either turn signal indicator has a very fast flash rate, check for a defective outside light bulb.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 High Beam/Low Beam Select Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you, to switch the headlights back to low beam. Flash-To-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will turn on the high beam headlights until the lever is released.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Light The cargo light is mounted in the headliner above the rear cargo area. This light will turn on when you open the liftgate or any door, or if you press the UNLOCK button on the RKE transmitter, or rotate the dimmer control on the multifunction lever completely upward to the second detent. Battery Saver Feature To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to the first detent to brighten the odometer and radio display when the parking lights or headlights are on during daylight conditions. Interior Light On Rotate the dimmer control completely upward to the second detent to turn on the interior lights. The interior lights will remain on when the dimmer control is in this position.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE they are operating. The wipers will resume operation when you turn the ignition switch to the ON position again. CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. • In cold weather, always turn off the wiper switch and allow the wipers to return to the “Park” position before turning off the engine.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 second to a maximum of approximately 18 seconds between cycles at vehicle speeds greater than 10 mph (16 km/h). WARNING! 3 Sudden loss of visibility through the windshield could lead to an accident. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with defroster before and during windshield washer use.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights with Wipers (Available with Auto Headlights Only) When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on if the multifunction lever (on the left side of the steering column) is placed in the AUTO position. In addition, the headlights will turn off when the wipers are turned off if they were turned on by this feature.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 • Use of Rain-X威 or products containing wax or silicone may reduce rain sensor performance. • The rain-sensing feature can be turned on and off through the Electronic Vehicle Information Center (EVIC) — if equipped. For details, refer to “Personal Settings (Customer-Programmable Features)” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual. The rain-sensing system has protective features for the wiper blades and arms.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Washers To use the washer, pull the windshield wiper/washer control lever toward you and hold it for as long as washer spray is desired. If you activate the washer while the wiper control is in the delay range, the wipers will operate in low-speed for two wipe cycles after releasing the lever and then resume the intermittent interval previously selected.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! Do not adjust the steering wheel while driving. The tilt adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the tilt adjustment locked could cause the driver to lose control of the vehicle. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over the accelerator operation at speeds greater than 25 mph (40 km/h).
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE simultaneously. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push and release the ON/OFF button located on the end of the Electronic Speed Control lever. The Cruise indicator lamp in the instrument cluster will illuminate. To turn the system off, push and release the ON/OFF button a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 To Deactivate A soft tap on the brake pedal, or pulling the Electronic Speed Control lever toward you (cancel), or normal brake or clutch pressure while slowing the vehicle will deactivate the speed control without erasing the set speed from memory. Pressing the ON/OFF button or turning off the ignition erases the set speed from memory. NOTE: For vehicles equipped with a manual transmission, pressing the clutch pedal will disengage the speed control.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate for Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Electronic Speed Control On Hills NOTE: The Electronic Speed Control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without Electronic Speed Control.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 System Usage Precautions NOTE: • Ensure that the rear bumper is free of dirt and debris to keep the Rear Park Assist System operating properly. • Jackhammers, large trucks, and other vibrations could affect the performance of the Rear Park Assist System. • When you turn off the Rear Park Assist System, the instrument cluster will display “PARK ASSIST DISABLED.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) WARNING! • The vehicle must be driven slowly when using the Rear Park Assist System to be able to stop in time when the obstacle is detected. It is recommended that the driver looks over his/her shoulder when using the Rear Park Assist System. • Clean the Rear Park Assist Sensors with water, car wash soap, and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could damage the sensors.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 WARNING! (Continued) • Before using the Rear Park Assist System, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be much closer to the obstacle than the rear fascia when the warning display turns the red LEDs ON.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Vehicles Equipped with Rear Park Assist Switch You can turn the Rear Park Assist System on or off by pressing the Rear Park Assist switch located the lower switch bank below the climate controls. System Operation The system uses four sensors located in the rear bumper fascia to scan for obstacles up to 79 in (200 cm) away from the rear bumper fascia.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 The warning display contains two sets of yellow and red LEDs, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle. The driver can view the LEDs either through the rear view mirror or by looking at the display above the rear window.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING DISPLAY DISTANCES DISPLAY LED Inner LED 1st LED 2nd LED 3rd LED 4th LED 5th LED 6th LED 7th LED OBSTACLE DISTANCE FROM: REAR CORNERS REAR CENTER 79 in (200 cm) 31.5 in (80 cm) 25.5 in (65 cm) 20 in (50 cm) 16 in (40 cm) 6 in (15 cm) 51 in (130 cm) 45 in (115 cm) 39 in (100 cm) 33.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 GARAGE DOOR OPENER — IF EQUIPPED HomeLink威 replaces up to three remote controls (handheld transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink威 unit operates off your vehicle’s battery. 3 The HomeLink威 buttons that are located in the headliner or sun visor designate the three different HomeLink威 channels.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982. Do not use a garage door opener without these safety features.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Place the hand-held transmitter 1–3 in (3-8 cm) away from the HomeLink威 button you wish to program while keeping the indicator light in view. 3. Simultaneously press and hold both the chosen HomeLink威 button and the hand-held transmitter button until the HomeLink威 indicator changes from a slow to a rapidly blinking light, then release both the HomeLink威 and hand-held transmitter buttons. Watch for the HomeLink威 indicator to change flash rates.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 6. Firmly press and release the “Learn” or “Training” button. The name and color of the button may vary by manufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink威 to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink姞 Button To re-program a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the ON/RUN position. 2. Press and hold the desired HomeLink威 button until the indicator light begins to flash after 20 seconds. Do not release the button. 3. Without releasing the button, proceed with Programming Homelink威 Step 2 and follow all remaining steps.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: POWER SUNROOF — IF EQUIPPED The power sunroof switch is located between the sun visors on the overhead console. 1. This device may not cause harmful interference. 3 2. This device must accept any interference that may be received including interference that may cause undesired operation.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Never leave unattended children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with an open sunroof. You could also be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 position. The sunroof will close fully and stop automatically. This is called “Express Close”. During Express Close operation, any movement of the switch will stop the sunroof. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold. This allows the sunroof to move towards the closed position. Closing Sunroof — Manual Mode To close the sunroof, press and hold the switch in the forward position.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Sky Slider姞 Usage Precautions CAUTION! (Continued) NOTE: • The system will not operate when ambient temperature is at –4°F (–20°C) or lower. • The system will not operate at vehicle speeds of 86 mph (138 km/h) or above. • Opening and closing the Sky Slider威 repeatedly without the engine running may run the battery down.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) Failure to follow these warnings can result in injuries that are serious or fatal to you, your passengers, and others around you: • In an accident, there is a greater risk of being thrown from a vehicle with the Sky Slider威 open. Always fasten your seat belt properly and make sure all passengers are properly secured too.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Sky Slider姞 Control The Sky Slider威 switch is located between the sun visors on the overhead console. Opening the Sky Slider姞 Using Automatic Mode Press the switch rearward and release it within one-half second and the Sky Slider威 will open from the front and move automatically toward the rear of the vehicle.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using Operator Mode Press the switch rearward and hold it, the Sky Slider威 will open from the front and move toward the rear of the vehicle. Press the switch forward and hold it, the Sky Slider威 will open from the rear and move toward the front of the vehicle. NOTE: During operation, any movement of the Sky Slider威 switch will stop the Sky Slider威 roof.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 completely. The left motor facing forward will close the top when it is open from the rear of the vehicle. The right motor will close the top when it is open from the front of the vehicle. Anti-Pinch Protect Feature The Sky Slider威 will retract automatically if it detects an obstruction while closing. If this occurs, remove the obstruction and use the switch again to close the Sky Slider威.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLET Your vehicle is equipped with a fused 12-Volt (DC) power outlet. This power outlet is located on the instrument panel, below the climate controls. It has power available when the ignition switch is in the ON or ACC position. Insert the cigar lighter or accessory plug into the outlet for use to ensure proper operation. NOTE: • To ensure proper operation a MOPAR威 knob and element must be used.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 CAUTION! CAUTION! (Continued) • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER INVERTER — IF EQUIPPED Your vehicle may be equipped with a 115-Volt AC (150 Watt maximum) power outlet located on the back of the center console. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will most power tools.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 NOTE: Due to built-in overload protection, the power outlet will shut down if the 115-Volt AC (150 Watt maximum) power rating is exceeded. WARNING! 115-Volt (150 Watt) Power Outlet Switch Press and release the switch once to turn on the power outlet. A status indicator in the switch will illuminate in approximately one second to indicate that power is available at the outlet. Press and release the switch again to turn off the power outlet.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS There are two cupholders for the front seat passengers, located in the center console. The rear passengers have cupholders at the rear of the center console.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 STORAGE Front Storage Compartment The front storage compartment (located on the left side of the instrument panel) can hold cell phones, PDAs, and other small items. Console Storage Compartment To open, press the latch and lift the cover.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The center console has a removable storage tray which can hold cell phones, PDAs, and other small items. CARGO AREA FEATURES Cargo Load Floor The cargo load floor system has a load capacity of 400 lbs (181 kg). The load floor has a built-in storage bin that can hold a variety of items. The underside of the storage bin cover also contains a plastic lined tray. The cover can be installed with either side facing up for added utility.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 1. Flip the spring-loaded latch pull-loops up. 4. Reinstall the cover with the handle recess facing toward you. NOTE: You can install the cover with either side facing upward. 5. With the cover seated in the floor, pull upward on loops and twist them one-quarter turn so that they are no longer parallel to the slots in the cover. 6. Flip the loops down. WARNING! Cargo Load Floor Loops 2.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Tie-Down Hooks and Loops The tie-downs located on cargo area floor should be used to secure loads safely when the vehicle is moving. Cargo Tie-Down Loops Cargo tie-down loops are located on the trim panels.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 WARNING! WARNING! • Cargo tie-downs are not safe anchors for a child seat tether strap. In a sudden stop or collision, a tie-down could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers. • To help protect against personal injury, passengers should not be seated in the rear cargo area.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not pile luggage or cargo higher than the top of the seatback. This could impair visibility or become a dangerous projectile in a sudden stop or collision. Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 Next, grab the cover handle and pull the cover toward you. As the cover nears the liftgate opening, guide the rear attachment posts (on both ends of the cover) into the notches in the trim panels. Then, lower the cover to position the posts into the bottom of the notches and release the handle.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In an accident, a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting. Do not store in the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 switch. Once released, the wiper will cycle three times, return to the park position, and then resume normal operation. NOTE: The rear wiper will automatically return to the park position if you turn OFF the ignition switch while it is operating. The rear wiper will resume operation when you turn the ignition switch to the ON position again. CAUTION! • Turn the rear wiper off when driving through an automatic car wash.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time. NOTE: To prevent excessive battery drain, use the rear window defroster only when the engine is operating. CAUTION! CAUTION! (Continued) • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window. • Keep all objects a safe distance from the window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 External racks do not increase the total load carrying capacity of the vehicle. Be sure that the total occupant and luggage load inside the vehicle, plus the load on the luggage rack, do not exceed the maximum vehicle load capacity. CAUTION! • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity. Always distribute heavy loads as evenly as possible and secure the load appropriately.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 Instrument Panel Features . . . . . . . . . . . . . . . 200 䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . 201 䡵 Instrument Cluster Descriptions . . . . . . . . . . . 202 䡵 Electronic Vehicle Information Center (EVIC) — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 215 ▫ Electronic Vehicle Information Center (EVIC) Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 ▫ Oil Change Required . . . . . . . . . . . . .
198 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Info Button (Disc Mode For MP3/WMA Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 䡵 AM/FM/CD/DVD Radio (RER/REN) – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 ▫ Operating Instructions — Voice Recognition System (VR) — If Equipped . . . . . . . . . . . . . 243 ▫ Operating Instructions — uconnect威 phone — If Equipped . . . . . . . . . . . . . . . . . . . . . . 243 ▫ Clock Setting Procedure . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 199 ▫ Electronic Serial Number/Sirius Identification Number (ESN/SID) . . . . . . . . . 266 䡵 Remote Sound System Controls — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 271 ▫ Selecting uconnect威 studios (Satellite) Mode . . . . . . . . . . . . . . . . . . . . . 267 ▫ Right-Hand Switch Functions . . . . . . . . . . . . 272 ▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . 267 ▫ Reception Quality . . . . . . . . . . . . . . . . . . . .
200 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Outlet 2 — Instrument Cluster 3 — Storage Tray 4 — Radio 5 — Glove Compartment 6 — Climate Control 7 — Power Outlet 8 — Lower Switch Bank 9 — Storage Bin (if equipped)
UNDERSTANDING YOUR INSTRUMENT PANEL 201 INSTRUMENT CLUSTER 4
202 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. 2. Fuel Door Reminder This symbol indicates the side of the vehicle where the fuel cap is located. 3. Low Fuel Light This indicator lights when the fuel level drops to approximately one-eighth tank. 4.
UNDERSTANDING YOUR INSTRUMENT PANEL 203 maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale.
204 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Electronic Throttle Control (ETC) Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the PARK position. The light should turn off.
UNDERSTANDING YOUR INSTRUMENT PANEL 205 7. High Beam Indicator This indicator shows that the high beam headlights are on. Pull the multifunction control lever on the left side of the steering column toward you to switch to low beam. 8. Front Fog Light Indicator — If Equipped This indicator will illuminate when the fog lights are on. 9. Speedometer Shows the vehicle speed. 10. Turn Signal Indicators The arrow will flash with the exterior turn signal when the turn signal lever is operated.
206 UNDERSTANDING YOUR INSTRUMENT PANEL the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. Obtain SERVICE IMMEDIATELY. See an authorized dealer. 13. Oil Pressure Warning Light This light indicates low engine oil pressure. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible.
UNDERSTANDING YOUR INSTRUMENT PANEL 207 15. Tachometer This gauge measures engine revolutions-per-minute (RPM x 1000). Before the pointer reaches the red area, ease up on the accelerator to prevent engine damage. 16. 4WD LOW Indicator — If Equipped This light alerts the driver that the vehicle is in the 4WD LOW mode. In this mode, the front driveshaft and rear driveshaft are mechanically locked together forcing the front and rear wheels to rotate at the same speed. 17.
208 UNDERSTANDING YOUR INSTRUMENT PANEL 20. Electronic Stability Program (ESP) / Brake Assist System (BAS) Indicator Light – If Equipped The malfunction indicator for the Electronic Stability Program (ESP) is combined with the Brake Assist System (BAS). The yellow “ESP/ BAS Warning Light” in the instrument cluster comes on when the ignition switch is turned to the ON position. It should go out with the engine running.
UNDERSTANDING YOUR INSTRUMENT PANEL 209 If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service. Refer to “If Your Engine Overheats” in Section 6 for more information. 23. Temperature Gauge The temperature gauge shows engine coolant temperature.
210 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealership for service if your vehicle overheats. If you decide to look under the hood yourself, see Section 7 of this manual. Follow the warnings under the Cooling System Pressure Cap paragraph. 24.
UNDERSTANDING YOUR INSTRUMENT PANEL 211 26. 4WD Indicator — Vehicles Equipped with Selec-Trac威 II This light alerts the driver that the vehicle is in the full-time four-wheel drive auto mode. In this mode, the system operates with a normal torque split of 42% front axle and 58% rear axle. It can redirect up to 100% of torque to the front or rear axle, if necessary. 27. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage.
212 UNDERSTANDING YOUR INSTRUMENT PANEL Fuel Cap Fault Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, the words “gASCAP” will display in the odometer. If this occurs, tighten the fuel filler cap properly and press the odometer reset button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started.
UNDERSTANDING YOUR INSTRUMENT PANEL 213 28. Cruise Indicator — If Equipped This indicator lights when the electronic speed control system is turned on. 29. Shift Lever Indicator This display indicator shows automatic transmission shift lever selection. 30. Seat Belt Reminder Light This light will turn on for several seconds after the ignition is turned ON as a reminder to “buckle up.” This light will remain on as long as the seat belt remains unbuckled. 31.
214 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is necessary. WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have an accident. Have the vehicle checked immediately.
UNDERSTANDING YOUR INSTRUMENT PANEL 215 33. Airbag Warning Light This light turns on and remains on for six to eight seconds as a bulb check when the ignition switch is first turned ON. If the light does not turn on during starting, stays on, or turns on while driving, have the system checked by an authorized dealer. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) features a driver-interactive display that is located in the instrument cluster.
216 UNDERSTANDING YOUR INSTRUMENT PANEL This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 217 Press the FUNCTION SELECT button to accept a selection. FUNCTION SELECT Button Electronic Vehicle Information Center (EVIC) Displays When the appropriate conditions exist, the EVIC displays the following messages.
218 UNDERSTANDING YOUR INSTRUMENT PANEL • Left/Right Rear Door Ajar (one or more, with a single chime if speed is above 1 mph(1.6 km/h)) • Door(s) Ajar (with a single chime if vehicle is in motion) • Liftgate Ajar (with a single chime) • Left Front Low Pressure (with a single chime). Refer to “Tire Pressure Monitoring System” in Section 5 of this manual. • Left Rear Low Pressure (with a single chime). Refer to “Tire Pressure Monitoring System” in Section 5 of this manual.
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Unless reset, this message will continue to display each time you turn the ignition switch to the ON position. To turn off the message temporarily, press and release the MENU button. To reset the oil change indicator system (after performing the scheduled maintenance) perform the following procedure: 1. Turn the ignition switch to the ON position. Do not start the engine.
220 UNDERSTANDING YOUR INSTRUMENT PANEL • Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset through the FUNCTION SELECT button.
UNDERSTANDING YOUR INSTRUMENT PANEL 221 Compass Display The compass readings indicate the direction the vehicle is facing. Press and release the COMPASS button to display one of eight compass readings and the outside temperature. Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to set the compass manually. When the vehicle is new, the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated.
222 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the “CAL” indicator turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To compensate for the differences, the variance should be set for the zone where the vehicle is driven, per the zone map.
UNDERSTANDING YOUR INSTRUMENT PANEL 223 4. Press and release FUNCTION SELECT button until the proper variance zone is selected according to the map. 5. Press and release the COMPASS button to exit. Personal Settings (Customer-Programmable Features) Personal Settings allows the driver to set and recall features when the vehicle speed is at 0 mph (0 km/h) (manual transmission) or when the shift lever is in PARK (auto transmission).
224 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Key Unlock When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the Remote Keyless Entry (RKE) transmitter UNLOCK button. When Driver Door 1st Press is selected, you must press the RKE transmitter UNLOCK button twice to unlock the passenger’s doors. When All Doors 1st Press is selected, all of the doors will unlock on the first press of the RKE transmitter UNLOCK button.
UNDERSTANDING YOUR INSTRUMENT PANEL 225 Automatically Move Seat Back on Exit — If Equipped This feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. To make your selection, press and release the FUNCTION SELECT button until “On” or “Off” appears. NOTE: The seat will return to the memorized seat location (if Recall Memory with Remote Key Unlock is set to ON) when the RKE transmitter is used to unlock the door.
226 UNDERSTANDING YOUR INSTRUMENT PANEL Delay Turning Headlights Off When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. To make your selection, press and release the FUNCTION SELECT button until “0,” “30,” “60,” or “90” appears. Turn Headlights On with Remote Key Unlock When this feature is selected, the headlights will activate and remain on for up to 90 seconds when the doors are unlocked with the RKE transmitter.
UNDERSTANDING YOUR INSTRUMENT PANEL 227 Hill Start Assist (HSA) — If Equipped When on is selected, the HSA system is active. Refer to “HSA (Hill Start Assist)” under “Electronic Brake Control System” in Section 5 of this manual for system function and operating information. To make your selection, press and release the FUNCTION SELECT button until “On” or “Off” appears.
228 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping. Turning the ON/VOLUME control knob to the right increases the volume and to the left decreases it.
UNDERSTANDING YOUR INSTRUMENT PANEL 229 If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With uconnect” message will display on the radio screen. TIME Button Press the TIME button to alternate locations of the time and frequency display. Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 5. To exit, press any button/knob or wait five seconds.
230 UNDERSTANDING YOUR INSTRUMENT PANEL Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary TUNE/SCROLL control knob a second time and MID will display.
UNDERSTANDING YOUR INSTRUMENT PANEL 231 Toggle the MUSIC TYPE button to select the following format types: Program Type No program type or undefined Adult Hits Classical Classic Rock College Country Foreign Language Information Jazz News Nostalgia Oldies 16-Digit Character Display None Adlt Hit Classicl Cls Rock College Country Language Inform Jazz News Nostalga Oldies Program Type Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top
232 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station.
UNDERSTANDING YOUR INSTRUMENT PANEL 233 NOTE: • The available selections for each of the above entries varies depending upon the disc. • Player Defaults - Selecting this item will allow the user to scroll through the following items and set defaults according to customer preference. • These selections can only be made while playing a DVD. Menu Language — If Equipped Selecting this item will allow the user to choose the default startup DVD menu language (effective only if language supported by disc).
234 UNDERSTANDING YOUR INSTRUMENT PANEL Subtitle Language — If Equipped Selecting this item allows you to choose a default subtitle language (effective only if the language is supported by the disc). You can select a language not listed by scrolling down and selecting ⬙other.⬙ Enter the country code using the TUNE/SCROLL control knob to scroll up and down to select the number and then push to select. Subtitles — If Equipped Selecting this item allows you to choose between subtitle Off or On.
UNDERSTANDING YOUR INSTRUMENT PANEL 235 SET Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET button, the station will continue to play but will not be stored into pushbutton memory.
236 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate “Disc Hot” and shut off until a safe temperature is reached. This shutdown is necessary to protect the optics of the DVD player and other radio internal components. NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 237 Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton with the corresponding number (1-6) where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙EJECTING DISC⬙ when the disc is being ejected and prompt the user to remove the disc. Press and hold the EJECT button for five seconds and all CDs will be ejected from the radio. The disc can be ejected with the radio and ignition OFF.
238 UNDERSTANDING YOUR INSTRUMENT PANEL Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however, acceptable MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the following restrictions.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ WMA tracks on that disc. MPEG Specification Supported MP3/WMA File Formats The radio will recognize only files with the *.MP3/WMA extension as MP3/WMA files. Non-MP3/WMA files named with the *.MP3/WMA extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3/WMA and will not play the file. MPEG-1 Audio Layer 3 48, 44.
240 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3/WMA files.
UNDERSTANDING YOUR INSTRUMENT PANEL 241 Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. SCAN Button (Auxiliary Mode) No function. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3/WMA player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
242 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Voice Recognition System (VR) (If Equipped) For the radio, refer to “Voice Recognition System (VR)” in Section 3. Dolby威 Manufactured under license from Dolby威 Laboratories. ⬙Dolby威⬙ and the double-D symbol are trademarks of Dolby威 Laboratories. For uconnect威 “Voice Recognition System (VR),” refer to “uconnect威 phone” in Section 3. Macrovision This product incorporates copyright protection technology that is protected by U.S.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 AM/FM/CD/DVD RADIO (RER/REN) – IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. The REN and RER radios contain a CD/DVD player, USB port, and a 30-gigabyte hard drive (HDD). Sirius Satellite Radio is optional. The 6.5 in (16.5 cm) touch screen allows for easy menu selection. The RER radio also contains a Global Positioning System (GPS)-based Navigation system.
244 UNDERSTANDING YOUR INSTRUMENT PANEL 4. To move the hour forward, touch the screen where the word “Hour” with the arrow pointing upward is displayed. To move the hour backward, touch the screen where the word “Hour” with the arrow pointing downward is displayed. 5. To move the minute forward, touch the screen where the word “Min” with the arrow pointing upward is displayed. To move the minute backward, touch the screen where the word “Min” with the arrow pointing downward is displayed. 6.
UNDERSTANDING YOUR INSTRUMENT PANEL 245 Changing the Time Zone 1. Turn on the radio. 2. Touch the screen where the time is displayed. The clock setting menu will appear on the screen. SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. 3. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen. 4 4.
246 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 5. To exit, press any button/knob, or wait five seconds. RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM or FM frequencies. TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency.
248 UNDERSTANDING YOUR INSTRUMENT PANEL SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET/RND button, the station will continue to play but will not be stored into pushbutton memory.
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Operation Instructions — CD MODE For CD And MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC position to operate the radio. • This radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up.
250 UNDERSTANDING YOUR INSTRUMENT PANEL EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. A disc can be ejected with the radio and ignition OFF. RW/FF Press and hold the FF (Fast Forward) button and the CD player will begin to fast forward until FF is released, or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 Press the RND button a second time to stop Random Play. Notes on Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
252 UNDERSTANDING YOUR INSTRUMENT PANEL Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
254 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES/RSC — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) AND SIRIUS RADIO NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 255 SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. Voice Recognition System (Radio) — If Equipped Refer to “Voice Recognition System (VR)” in Section 3.
256 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save time change. 5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button. For vehicles equipped with satellite radio, press the SETUP button, use the TUNE/SCROLL control to select SET CLOCK, and then follow the above procedure, starting at Step 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type information. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display.
258 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather 16-Digit Character Display News Nostalga Oldies Persnlty Public R&B Rel Musc Rel Talk Rock Soft Soft Rck Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type na
UNDERSTANDING YOUR INSTRUMENT PANEL 259 AM/FM Button Press the button to select either AM or FM mode. SET/RND Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND button. The symbol SET 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that button.
260 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions — CD MODE for CD and MP3 Audio Play NOTE: • The ignition switch must be in the ON or ACC position to operate the radio. • This radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks. Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 EJECT Button - Ejecting a CD Press the EJECT button to eject the CD. TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. A disc can be ejected with the radio and ignition OFF. RW/FF Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner.
262 UNDERSTANDING YOUR INSTRUMENT PANEL Press the SET/RND button a second time to stop Random Play. Notes On Playing MP3 Files The radio can play MP3 files; however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restrictions. Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 File Formats The radio will recognize only files with the *.MP3 extension as MP3 files.
264 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack which allows the user to plug in a portable device such as an MP3 player or cassette player and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the AUX button will change the mode to auxiliary device if the AUX jack is connected.
266 UNDERSTANDING YOUR INSTRUMENT PANEL uconnect姞 studios (SATELLITE RADIO) — IF EQUIPPED (REN/REQ/RER/RES/REU RADIOS ONLY) Satellite radio uses direct satellite-to-receiver broadcasting technology to provide clear digital sound, coast to coast. The subscription service provider is Sirius Satellite Radio. This service offers over 130 channels of music, sports, news, entertainment, and programming for children, directly from its satellites and broadcasting studios.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 selected. Press the TUNE/SCROLL control knob and the Sirius ID number will display. The Sirius ID number display will time out in two minutes. Press any button on the radio to exit this screen. Selecting uconnect姞 studios (Satellite) Mode Press the SAT button until ⬙SAT⬙ appears in the display. A CD may remain in the radio while in the Satellite radio mode. ESN/SID Access With REN/RER Radios While in SAT mode, press the MENU button on the radio faceplate.
268 UNDERSTANDING YOUR INSTRUMENT PANEL • Dense tree coverage may interrupt reception in the form of short audio mutes. • Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage. Operating Instructions — uconnect姞 studios (Satellite) Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next channel in the direction of the arrows. TUNE Control (Rotary) Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the channel. MUSIC TYPE Button — Except REU Radio Pressing this button once will turn on the Music Type mode for five seconds.
270 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number. This number is used to activate, deactivate, or change the Sirius subscription. SET Button – To Set the Pushbutton Memory When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 Operating Instructions — uconnect姞 phone (If Equipped) Refer to “uconnect威 phone” in Section 3. Operating Instructions — Video Entertainment System (VES)™ (If Equipped) Refer to separate “Video Entertainment System (VES)™ Guide.” REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. The left and right controls are rocker-type switches with a pushbutton in the center of each switch.
272 UNDERSTANDING YOUR INSTRUMENT PANEL Right-Hand Switch Functions • Press the top of the switch to increase the volume. • Press the bottom of the switch to decrease the volume. • Press the button in the center of the switch to change modes (i.e., AM, FM, etc.). Left-Hand Switch Functions for Radio Operation • Press the top of the switch to SEEK the next listenable station up from the current setting. • Press the bottom of the switch to SEEK the next listenable station down from the current setting.
UNDERSTANDING YOUR INSTRUMENT PANEL 273 CD/DVD MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratching the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or anti-static sprays. 5. Store the disc in its case after playing. 6.
274 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The Air Conditioning and Heating System is designed to make you comfortable in all types of weather. Manual Air Conditioning and Heating System Blower Control Use this control to regulate the amount of air forced through the ventilation system in any mode. The blower speed increases as you move the control to the right from the “O” (Off) position. There are four blower speeds.
UNDERSTANDING YOUR INSTRUMENT PANEL 275 NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C condenser (located in front of the radiator) for an accumulation of dirt or insects. Clean with a gentle water spray from behind the radiator and through the condenser. Fabric front fascia protectors may reduce airflow to the condenser, reducing air conditioning performance. Mode Control (Air Direction) Use this control to choose from several patterns of air distribution.
276 UNDERSTANDING YOUR INSTRUMENT PANEL • Mix Air is directed through the floor, defrost, and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield. • Defrost Air is directed through the windshield and side window demist outlets. Use this mode with maximum blower and temperature settings for best windshield and side window defrosting.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 • The A/C can be deselected manually without disturbing the mode control selection. Automatic Temperature Control (ATC) — If Equipped Air Conditioning Control Use this button to engage the Air Conditioning. A light will illuminate when the Air Conditioning System is engaged 4 NOTE: The air conditioning compressor will not engage until the engine has been running for about 10 seconds.
278 UNDERSTANDING YOUR INSTRUMENT PANEL accomplish this, the system gathers information from the cabin infrared sensor mounted between the sun-visors and from various sensors located throughout the vehicle. The controls on the climate control provide the system with operator input. Other sensors take account of vehicle speed, A/C pressure, outside temperature, and engine cooling temperature.
UNDERSTANDING YOUR INSTRUMENT PANEL 279 NOTE: • The temperature setting can be adjusted at anytime without affecting automatic operation. • Pressing the Air Conditioning Control button while in AUTO mode will cause the LED in the control button to flash three times and then turn off. This indicates that the system is in AUTO mode and requesting the air conditioning is not necessary.
280 UNDERSTANDING YOUR INSTRUMENT PANEL
UNDERSTANDING YOUR INSTRUMENT PANEL 281 The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control knob (on the right) to one of the following positions. • Panel Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct airflow. NOTE: The center instrument panel outlets can be aimed so that they are directed toward the rear seat passengers for maximum airflow to the rear.
282 UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control Press this button to turn on the air conditioning during manual operation only. When the air conditioning is turned on, cool dehumidified air will flow through the outlets selected with the Mode control dial. Press this button a second time to turn off the air conditioning. An LED in the button illuminates when manual compressor operation is selected. • Recirculation Control The system will automatically control recirculation.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 • Most of the time, when in Automatic Operation, you can temporarily put the system into Recirculation mode by pressing the RECIRCULATION button. However, under certain conditions, while in Automatic Mode, the system is blowing air out the defrost vents. When these conditions are present, and the RECIRCULATION button is pressed, the indicator will flash and then turn off. This tells you that you are unable to go into recirculation mode at this time.
284 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Interior fogging on the windshield can be quickly removed by turning the mode selector to Defrost. The Defrost/Floor mode can be used to maintain a clear windshield and provide sufficient heating. If side window fogging becomes a problem, increase blower speed. Vehicle windows tend to fog on the inside in mild but rainy or humid weather. NOTE: Recirculate without A/C should not be used for long periods as fogging may occur.
UNDERSTANDING YOUR INSTRUMENT PANEL 285 Control Setting Suggestions for Various Weather Conditions 4
STARTING AND OPERATING CONTENTS 䡵 Starting Procedures . . . . . . . . . . . . . . . . . . . . 291 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 291 ▫ Extreme Cold Weather (Below –20°F Or –29°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . 292 ▫ After Starting . . . . . . . . . . . . . . . . . . . . . . . 293 䡵 Engine Block Heater — If Equipped . . . . . . . . 293 䡵 Automatic Transmission . . . . . . . . . . . . . . . . .
288 STARTING AND OPERATING 䡵 Off-Road Driving Tips . . . . . . . . . . . . . . . . . . 314 ▫ Traction Control System (TCS) . . . . . . . . . . . 325 ▫ When To Use 4WD Low Range . . . . . . . . . . 314 ▫ Brake Assist System (BAS) . . . . . . . . . . . . . . 325 ▫ Driving Through Water . . . . . . . . . . . . . . . . 314 ▫ Electronic Roll Mitigation (ERM) . . . . . . . . . 326 ▫ Driving In Snow, Mud And Sand . . . . . . . . . 315 ▫ Trailer Sway Control (TSC) — If Equipped . . . . . . . . . . . . . . .
STARTING AND OPERATING 289 ▫ Tire Loading And Tire Pressure . . . . . . . . . . 342 䡵 Tires — General Information 䡵 Tire Pressure Monitor System (TPMS) . . . . . . . 356 . . . . . . . . . . . . . 346 ▫ Base System . . . . . . . . . . . . . . . . . . . . . . . . 358 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . 346 ▫ Premium System — If Equipped . . . . . . . . . 361 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . 347 ▫ General Information . . . . . . . . . . . . . . . . .
290 STARTING AND OPERATING 䡵 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 370 ▫ Trailer And Tongue Weight . . . . . . . . . . . . . 382 ▫ Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . 370 ▫ Towing Requirements . . . . . . . . . . . . . . . . . 383 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 371 ▫ Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . 388 䡵 Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . 371 ▫ Certification Label . . . . . . . . .
STARTING AND OPERATING 291 STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Start the engine with the shift lever in the NEUTRAL or PARK position. Apply the brake before shifting to any driving range.
292 STARTING AND OPERATING If Engine Fails to Start WARNING! (Continued) WARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. (Continued) • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way.
STARTING AND OPERATING 293 With Tip Start If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold Weather” procedures, it may be flooded. To clear any excess fuel, push the accelerator pedal all the way to the floor and hold it. Then, turn the ignition switch to the START position and release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds.
294 STARTING AND OPERATING WARNING! CAUTION! (Continued) Remember to disconnect the cord before driving. Damage to the 110-115 Volt AC electrical cord could cause electrocution. Use the heater when temperatures below 0 °F (-18 °C) are expected to last for several days. AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop.
STARTING AND OPERATING 295 WARNING! It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your foot is firmly on the brake pedal.
296 STARTING AND OPERATING 5. Using the screwdriver, reach into the manual override opening. Press and hold the shift lock lever down. Have your vehicle inspected by your local authorized dealer if the shift lock manual override has been used. 4–Speed Automatic Transmission NOTE: Under extreme cold temperatures (-6°F (-21°C) and when in DRIVE, transmission operation may be briefly limited to only second gear operation.
STARTING AND OPERATING 297 Gear Ranges Do not race the engine when shifting from PARK or NEUTRAL position into another gear range. PARK This range supplements the parking brake by locking the transmission. The engine can be started in this range. Never use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, then place the shift lever in the PARK position.
298 STARTING AND OPERATING WARNING! (Continued) • It is dangerous to move the shift lever out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal. REVERSE This range is for moving the vehicle rearward.
STARTING AND OPERATING 299 Overdrive Operation The overdrive automatic transmission contains an electronically controlled 4th speed (OVERDRIVE).
300 STARTING AND OPERATING When To Use TOW/HAUL Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, press the TOW/HAUL button. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting. When operating in TOW/HAUL mode, the transmission will shift to 3rd gear. NOTE: TOW/HAUL mode locks out Overdrive.
STARTING AND OPERATING 301 Transmission Limp Home Mode Transmission function is monitored for abnormal conditions. If a condition is detected that could result in transmission damage, the Transmission Limp Home Mode will be engaged. In this mode, the transmission will remain in second gear in any forward driving range. If the problem is no longer detected, the transmission will return to normal operation. If the problem persists, PARK, REVERSE, and NEUTRAL will continue to operate.
302 STARTING AND OPERATING FOUR-WHEEL DRIVE OPERATION MP1522 Command-Trac姞 Transfer Case — If Equipped Operating Information and Precautions The Command-Trac威 transfer case provides four positions: • Two–wheel drive (2WD) high range • Four-wheel drive (4WD LOCK) high range • Four-wheel drive (4WD LOW) low range • Neutral (N) This transfer case is intended to be driven in the twowheel drive position (2WD) for normal street and highway conditions such as dry hard-surfaced roads.
STARTING AND OPERATING 303 CAUTION! (Continued) WARNING! • The 4WD LOCK position and 4WD LOW position are intended for loose or slippery road surfaces only. Driving in these positions on dry hardsurfaced roads may cause increased tire wear and damage to the driveline components. • When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 2WD position or 4WD LOCK position at a given road speed.
304 STARTING AND OPERATING WARNING! (Continued) • Since four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit. You or others could be injured. Shift Positions The electronic transfer case switch is located on the center console next to the shift lever. 4WD Control Switch 2WD Rear Wheel Drive High Range - This range is used for normal street and highway driving on dry hard-surfaced roads.
STARTING AND OPERATING 305 4WD Lock 4-Wheel Drive High Range - This range locks the front driveshaft and rear driveshaft together forcing the front and rear wheels to rotate at the same speed. Additional traction for loose or slippery road surfaces only. 4WD Low 4-Wheel Drive Low Range - This range provides low speed four-wheel drive. Locks the front driveshaft and rear driveshaft together forcing the front and rear wheels to rotate at the same speed.
306 STARTING AND OPERATING Shifting Procedures NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift, the indicator light for the previous position will remain on, and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met.
STARTING AND OPERATING 307 Shifting can be performed with the vehicle rolling 2 to 3 mph (3 to 5 km/h) using the “Preferred Procedure” or completely stopped using the “Alternate Procedure.” 2. With the ignition switch in the ON position, and the engine OFF or RUNNING, shift the transmission into NEUTRAL. Preferred Procedure 3. Move the 4WD Control Switch to the desired position. 1. With the engine RUNNING, slow the vehicle speed to 2 to 3 mph (3 to 5 km/h). 4.
308 STARTING AND OPERATING operable. If the ignition switch is not in the ON position, then the shift will not take place and no position indicator lights will be on or flashing.
STARTING AND OPERATING 309 CAUTION! (Continued) WARNING! • When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 2WD position or 4WD AUTO position at a given road speed. Take care not to over-speed the engine and do not exceed 25 mph (40 km/h). • Proper operation of four-wheel drive vehicles depends on tires of equal size, type, and circumference on each wheel. Any difference in tire size can cause damage to the transfer case.
310 STARTING AND OPERATING WARNING! (Continued) • Since four-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit. You or others could be injured. Shift Positions The electronic transfer case switch is located on the center console next to the gear selector lever. 4WD Control Switch 2WD Rear Wheel Drive High Range - This range is for normal street and highway driving on dry hard-surfaced roads.
STARTING AND OPERATING 311 wide range of conditions, while maximizing driver convenience. This position is always in four-wheel drive mode, with a normal 42% front axle, 58% rear axle torque split. The system also anticipates and prevents slip by redirecting torque as necessary, up to 100% to the front or rear axle, if needed. 4WD Low Four-Wheel Drive Low Range - This range is for low speed four-wheel drive.
312 STARTING AND OPERATING Shifting Procedures NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift, the indicator light for the previous position will remain on, and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met.
STARTING AND OPERATING 313 Alternate Procedure 1. Bring the vehicle to a complete stop. 2. With the ignition switch in the ON position and the engine OFF or RUNNING, shift the transmission into NEUTRAL. 3. Move the 4WD Control Switch to the desired position. 4. After the desired position indicator light is on (not flashing), shift the transmission into gear. NOTE: Steps 1 and 2 in the “Preferred Procedure” and the “Alternate Procedure” are requirements for shifting the transfer case.
314 STARTING AND OPERATING turns or abrupt maneuvers. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or vehicle rollover. OFF-ROAD DRIVING TIPS When To Use 4WD LOW Range When off-road driving, shift to 4WD LOW for additional traction and control on slippery or difficult terrain, ascending or descending steep hills, and to increase low-speed pulling power.
STARTING AND OPERATING 315 entering. Proceed with caution and maintain a steady controlled speed less than 5 mph (8 km/h) in deep water to minimize wave effects. Flowing Water If the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes and/or the flow rate is reduced. If you must cross flowing-water, avoid depths in excess of 9 in (22 cm). The flowing water can erode the streambed causing your vehicle to sink into deeper water.
316 STARTING AND OPERATING Hill Climbing NOTE: Before attempting to climb a hill, determine the conditions at the crest and/or on the other side. Before climbing a steep hill, shift the transmission to a lower gear and shift the transfer case to 4WD LOW. Use first gear and 4WD LOW for very steep hills. If you stall or begin to lose headway while climbing a steep hill, allow your vehicle to come to a stop and immediately apply the brakes. Restart the engine and shift to REVERSE.
STARTING AND OPERATING 317 Traction Downhill Shift the transmission into a low gear and the transfer case to 4WD LOW range. Let the vehicle go slowly down the hill with all four wheels turning against engine compression drag. This will permit you to control the vehicle speed and direction. When descending mountains or hills, repeated braking can cause brake fade with loss of braking control. Avoid repeated heavy braking by downshifting the transmission whenever possible.
318 STARTING AND OPERATING WARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. You might not have full braking power when you need it to prevent an accident. If you have been operating your vehicle in dirty conditions, get your brakes checked and cleaned as necessary. • If you experience unusual vibration after driving in mud, slush, or similar conditions, check the wheels for impacted material.
STARTING AND OPERATING 319 WARNING! Continued operation with reduced power steering assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. apparent, and/or the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer. No chemical flushes should be used in any power steering system; only the approved lubricant may be used.
320 STARTING AND OPERATING PARKING BRAKE To set the parking brake, pull the lever up as firmly as possible. When the parking brake is applied with the ignition ON, the “Brake Warning Light” in the instrument cluster will light. To release the parking brake, pull up slightly, press the center button, then lower the lever completely. NOTE: The “Brake Warning Light” indicates only that the parking brake is applied. You must be sure the parking brake is fully applied before leaving the vehicle.
STARTING AND OPERATING 321 WARNING! • Always apply the parking brake fully when leaving your vehicle or it may roll and cause damage or injury. Also, be certain to leave the transmission in the PARK position. Failure to do so may allow the vehicle to roll and cause damage or injury. • Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be injured. Do not leave the keys in the ignition.
322 STARTING AND OPERATING WARNING! WARNING! Significant over or under-inflation of tires or mixing sizes of tires or wheels on the vehicle can lead to loss of braking effectiveness. • Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
STARTING AND OPERATING 323 WARNING! (Continued) • The capabilities of an ABS equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of others. CAUTION! The ABS is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or telephones. NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard.
324 STARTING AND OPERATING build up between the tire tread and the road. This hydroplaning action can cause loss of traction, braking ability, and control. • After going through deep water or a car wash, brakes may become wet, resulting in decreased performance and unpredictable braking action. Dry the brakes by gentle, intermittent pedal action while driving at very slow speeds.
STARTING AND OPERATING 325 WARNING! The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ABS cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, attentive, and skillful driver can prevent accidents.
326 STARTING AND OPERATING benefit of the system, you must apply continuous braking pressure during the stopping sequence, (do not “pump” the brakes). Do not reduce brake pedal pressure unless braking is no longer desired. Once the brake pedal is released, the BAS is deactivated. WARNING! The Brake Assist System (BAS) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions.
STARTING AND OPERATING 327 WARNING! Many factors, such as vehicle loading, road conditions, and driving conditions, influence the chance that wheel lift or rollover may occur. Electronic Roll Mitigation (ERM) cannot prevent all wheel lift or rollovers, especially those that involve leaving the roadway or striking objects or other vehicles. Only a safe, attentive, and skillful driver can prevent accidents.
328 STARTING AND OPERATING WARNING! (Continued) • Failure to follow these warnings can result in an accident or serious personal injury. Hill Start Assist (HSA) The HSA system is designed to help the driver accelerate the vehicle from a complete stop while on an incline. If the driver releases the brake while stopped on an incline, HSA will continue to hold the brake pressure for a short period.
STARTING AND OPERATING 329 WARNING! WARNING! There may be situations where the Hill Start Assist (HSA) will not activate and slight rolling may occur, such as on minor hills (i.e., less than 7%), or with a loaded vehicle, or while pulling a trailer. HSA is not a substitute for active driving involvement.
330 STARTING AND OPERATING Disabling and Enabling HSA This feature can be turned on or turned off. To change the current setting, proceed as follows: For vehicles equipped with the Electronic Vehicle Information Center (EVIC), refer to “Hill Start Assist,” under ⬙Personal Settings (Customer Programmable Features),” under “Electronic Vehicle Information Center (EVIC)” in Section 4 of this manual.
STARTING AND OPERATING 331 Hill Descent Control (HDC) — If Equipped HDC is only intended for low speed off-road driving. HDC maintains vehicle speed while descending hills in off-road driving conditions by applying the brakes when necessary. HDC control speed. If more speed is desired during HDC control, the accelerator pedal will increase vehicle speed in the usual manner. When either the brake or the accelerator is released, HDC will control the vehicle at the original set speed.
332 STARTING AND OPERATING The “Hill Descent” button is located in the lower switch bank below the climate control. 2. Press the “Hill Descent” button. The “Hill Descent Control Indicator Light” in the instrument cluster will turn on solid. NOTE: If the transfer case is not in 4WD LOW range, the “Hill Descent Control Indicator Light” will flash for five seconds and HDC will not be enabled. Disabling HDC 1. Press the “Hill Descent” button or shift the transfer case out of 4WD LOW range.
STARTING AND OPERATING 333 The ESP uses sensors in the vehicle to determine the path that the driver intends to steer the vehicle and compares it to the actual path of the vehicle. When the actual path does not match the intended path, the ESP applies the brake of the appropriate wheel to assist in counteracting the condition of over-steer or under-steer. • Oversteer - when the vehicle is turning more than appropriate for the steering wheel position.
334 STARTING AND OPERATING Depending upon model and mode of operation, the ESP system has up to three operating modes: “ESP On” “Partial Off,” and “Full Off.” ESP On — Two-Wheel Drive Vehicles and Four-Wheel Drive Vehicles in 2WD and 4WD High Range This is the normal operating mode for ESP when operating a two-wheel drive vehicle. It is also the normal mode for operating a four-wheel drive vehicle in 2WD or 4WD HIGH range.
STARTING AND OPERATING 335 mode is overcome, turn ESP back on by momentarily depressing the “ESP OFF” button. This may be done while the vehicle is in motion. Full Off — Four-Wheel Drive Vehicles in 4WD High and 4WD Low Range The “Full Off” mode is intended for off-highway and off-road use when ESP stability features could inhibit vehicle maneuverability due to trail conditions.
336 STARTING AND OPERATING In this mode, ESP and TCS are turned off (except for the “limited slip” feature described in the TCS section) until the vehicle reaches a speed of 40 mph (64 km/k). At speeds over 40 mph (64 km/k), the system automatically switches to “Partial Off” mode, described above. When the vehicle speed returns to less than 35 mph (56 km/h), the ESP system will return to “Full Off” mode. The “ESP/TCS Indicator Light” is always illuminated when ESP is off.
STARTING AND OPERATING 337 running. If the “ESP/BAS Malfunction Indicator Light” turns on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system, or both. If this light remains on after several ignition cycles, and the vehicle has been driven several miles/kilometers at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected.
338 STARTING AND OPERATING NOTE: • P (Passenger) - Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European-Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter ⬙P⬙ is absent from this tire size designation. Example: 215/65R15 96H.
STARTING AND OPERATING 339 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
340 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING 341 Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the outboard side, then you will find it on the inboard side of the tire.
342 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires.
STARTING AND OPERATING 343 NOTE: Under a maximum loaded vehicle condition, gross axle weight ratings (GAWRs) for the front and rear axles must not be exceeded. For further information on GAWRs, vehicle loading, and trailer towing, refer to “Vehicle Loading” in this section. To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on the Tire and Loading Information placard.
344 STARTING AND OPERATING 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
STARTING AND OPERATING 345 5
346 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
STARTING AND OPERATING 347 WARNING! (Continued) • Unequal tire pressures can cause steering problems. You could lose control of your vehicle. • Over-inflated or under-inflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control. • Unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recommended cold tire inflation pressure.
348 STARTING AND OPERATING The pressure should be checked and adjusted, as well as inspected for signs of tire wear or visible damage, at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under-inflated. (1.6 km) after a three-hour period. The cold tire inflation pressure must not exceed the maximum inflation pressure molded into the tire sidewall.
STARTING AND OPERATING 349 Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build-up, or your tire pressure will be too low. Tire Pressures For High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
350 STARTING AND OPERATING Cuts and punctures in radial tires are repairable only in the tread area because of sidewall flexing. Consult your authorized dealer for radial tire repairs. Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and reinstalled at the first opportunity.
STARTING AND OPERATING 351 CAUTION! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with the compact spare installed. Damage to the vehicle may result. Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 35 mph (55 km/h).
352 STARTING AND OPERATING These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the indicators appear in two or more adjacent grooves, the tire should be replaced.
STARTING AND OPERATING 353 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have an accident resulting in serious injury or death.
354 STARTING AND OPERATING CAUTION! CAUTION! (Continued) To avoid damage to your vehicle, tires, or chains, observe the following precautions: • Do not use tire chains on vehicles equipped with tires other than P225/75R16 or smaller tires. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle. • Because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used.
STARTING AND OPERATING 355 These cautions apply to all chain traction devices, including link and cable (radial) chains. TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, handling, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. The suggested rotation method is the “forward-cross” shown in the following diagram.
356 STARTING AND OPERATING Refer to the “Maintenance Schedule” in Section 8 of this manual for the proper maintenance intervals. Remember, more frequent rotation is permissible if desired. Also, correct for anything causing rapid or unusual wear prior to performing the tire rotation. tire sidewall. Refer to the “Tires – General Information” in this section for information on how to properly inflate the vehicle’s tires. The tire pressure will also increase as the vehicle is driven.
STARTING AND OPERATING 357 Telltale Light will turn off once the system receives the updated tire pressures. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information. For example, your vehicle may have a recommended cold (parked for more than three hours) placard pressure of 33 psi (227 kPa).
358 STARTING AND OPERATING NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure. • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.
STARTING AND OPERATING 359 The matching full-size spare wheel and tire assembly (if equipped) has a tire pressure monitoring sensor. The matching full-size spare can be used in place of any of the four road tires. The TPMS will only monitor the pressure in the full-size spare when it is used in place of a road tire. Otherwise, a spare with a pressure below the lowpressure limit will not cause the Tire Pressure Monitoring Telltale Light to illuminate or the chime to sound.
360 STARTING AND OPERATING 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPMS sensors. Vehicles with Full-Size Spare 1. The matching full-size spare wheel and tire assembly has a tire pressure monitoring sensor that can be monitored by the TPMS. 2.
STARTING AND OPERATING 361 Telltale Light will turn off, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information.
362 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the Electronic Vehicle Information Center (EVIC) will display a graphic showing the pressure values of each tire with the low tire pressure values flashing.
STARTING AND OPERATING 363 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPMS sensors. 2. Installing some form of aftermarket window tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or wheel housings. 4. Using tire chains on the vehicle. 5. Using wheels/tires not equipped with TPMS sensors. If the ignition key is cycled, this sequence will repeat, providing the system fault still exists.
364 STARTING AND OPERATING on upon the next ignition key cycle. In addition, the EVIC will display a Low Pressure message and a graphic showing the low tire pressure value flashing. 3. After driving the vehicle for up to 20 minutes above 15 mph (25 km/h) the TPMS Telltale Light will turn OFF, as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires. 4.
STARTING AND OPERATING 365 5. Once you repair or replace the original road tire and reinstall it on the vehicle in place of the compact spare, the TPMS will update automatically. In addition, the TPMS Telltale Light will turn off and the graphic in the EVIC will display a new pressure value instead of dashes (- -), as long as no tire pressure is below the low-pressure warning limit in any of the four active road tires.
366 STARTING AND OPERATING as hard starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline before considering service for the vehicle. Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the Worldwide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle.
STARTING AND OPERATING 367 Problems that result from using methanol/gasoline or E85 Ethanol blends are not the responsibility of the manufacturer. While MTBE is an oxygenate made from Methanol, it does not have the negative effects of Methanol. E-85 Usage In Non-Flex Fuel Vehicles Non-FFV vehicles are compatible with gasoline containing 10% ethanol (E10). Gasoline with higher ethanol content may void the vehicle’s warranty.
368 STARTING AND OPERATING of gasoline may not be indicated on the gasoline pump; therefore, you should ask your gasoline retailer whether the gasoline contains MMT. It is even more important to look for gasolines without MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. MMT is prohibited in Federal and California reformulated gasoline. Materials Added To Fuel All gasoline sold in the United States is required to contain effective detergent additives.
STARTING AND OPERATING 369 • The use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you.
370 STARTING AND OPERATING ADDING FUEL CAUTION! Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door on the left side of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is designed for use with this vehicle. • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system.
STARTING AND OPERATING 371 WARNING! (Continued) • Never add fuel to the vehicle when the engine is running. • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. NOTE: • Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is tightened properly. The MIL in the instrument cluster may turn on if the gas cap is not secured properly.
372 STARTING AND OPERATING This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and indicates the month, day, and hour of manufacture. The bar code that appears on the bottom of the label is your VIN.
STARTING AND OPERATING 373 Inflation Pressure This is the cold tire inflation pressure for your vehicle for all loading conditions up to full GAWR. Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.
374 STARTING AND OPERATING CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also, overloading can shorten the life of your vehicle. TRAILER TOWING In this section, you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle.
STARTING AND OPERATING 375 WARNING! WARNING! If the Gross Trailer Weight (GTW) is 3,500 lbs (1 587 kg) or more, it is mandatory to use a weight-distributing hitch to ensure stable handling of your vehicle. If you use a standard weight- carrying hitch, you could lose control of your vehicle and cause an accident. It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded.
376 STARTING AND OPERATING Trailer Sway Control — Electronic Refer to “TSC (Trailer Sway Control)” under “Electronic Brake Control System” in this section for information on this system. Trailer Sway Control — Mechanical The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.
STARTING AND OPERATING 377 WARNING! • An improperly adjusted Weight Distributing Hitch system may reduce handling, stability, braking performance, and could result in an accident. • Weight Distributing Systems may not be compatible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
378 STARTING AND OPERATING With Weight Distributing Hitch (Correct) Improper Adjustment of Weight-Distributing Hitch (Incorrect)
STARTING AND OPERATING 379 Trailer Hitch Classification Your vehicle is capable of towing trailers up to 2,000 lbs (907 kg) without added equipment or alterations to the standard equipment. Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package. See your authorized dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow.
380 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ Transmission 3.7L/Automatic 3.7L/Automatic 3.7L/Automatic w/ Cooler 3.7L/Automatic w/Cooler Model Frontal Area Tongue Wt. (See Note) 32 sq ft (2.97 sq m) 32 sq ft (2.97 sq m) 64 sq ft (5.94 sq m) Max. GTW (Gross Trailer Wt.) 2,000 lbs (907 kg) 2,000 lbs (907 kg) 3,500 lbs (1 588 kg) 4x2 4x4 4x2 4x4 64 sq ft (5.
STARTING AND OPERATING 381 When Towing Trailers with Gross Trailer Weight (GTW) between 3,500 Lbs (1 588 kg) and 5,000 Lbs (2 268 kg) The following chart provides maximum trailer weight ratings towable for the following engine/transmission combinations, ONLY if using a weight distributing hitch. Engine/ Transmission 3.7L/Automatic w/ Cooler 3.7L/Automatic w/Cooler Model Frontal Area Tongue Wt. (See Note) 64 sq ft (5.94 sq m) Max. GTW (Gross Trailer Wt.) 5,000 lbs (2 268 kg) 4x2 4x4 64 sq ft (5.
382 STARTING AND OPERATING Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle. Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer. Failure to load trailers heavier in front is the cause of many trailer accidents.
STARTING AND OPERATING 383 NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the “Tire and Loading Information” placard for the maximum combined weight of occupants and cargo for your vehicle.
384 STARTING AND OPERATING • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle transmission in PARK. Always, block or ⬙chock⬙ the trailer wheels. • GCWR must not be exceeded.
STARTING AND OPERATING 385 − Check for signs of tire wear or visible tire damage before towing a trailer. Refer to “Tires–General Information” in this section for information on tread wear indicators and for the proper inspection procedure. − When replacing tires, refer to “Tires–General Information” in this section for information on replacement tires and for the proper tire replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s GVWR and GAWR limits.
386 STARTING AND OPERATING WARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines. It can overload your brake system and cause it to fail. You might not have brakes when you need them and could have an accident. • Towing any trailer will increase your stopping distance. When towing you should allow for additional space between your vehicle and the vehicle in front of you. Failure to do so could result in an accident.
STARTING AND OPERATING 387 5 Four-Pin Connector 1 — Female Pins 2 — Male Pin 3 — Ground 4 — Park 5 — Left Stop/Turn 6 — Right Stop/Turn Seven-Pin Connector 1 2 3 4 — — — — Battery Backup Lamps Right Stop/Turn Electric Brakes 5 — Ground 6 — Left Stop/Turn 7 — Running Lamps
388 STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic. Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, you will want to activate the TOW/HAUL feature. Refer to “Automatic Transmission” in this section for additional information.
STARTING AND OPERATING 389 Cooling System To reduce potential for engine and transmission overheating, take the following actions: − City Driving When stopped for short periods of time, put transmission in NEUTRAL and increase engine idle speed. − Highway Driving Reduce speed. − Air Conditioning Turn off temporarily. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing – Two-Wheel Drive Models Recreational towing is allowed ONLY if the driveshaft is removed.
390 STARTING AND OPERATING CAUTION! (Continued) • Before recreational towing, perform the procedure outlined under “Shifting into NEUTRAL” to be certain that the transfer case is fully in NEUTRAL. Otherwise, internal damage will result. • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. Shifting into NEUTRAL Perform the following procedure to prepare your vehicle for recreational towing: 1. Bring the vehicle to a complete stop. 2. Turn OFF the engine. 3.
STARTING AND OPERATING 391 10. Repeat Steps 8 and 9 with the transmission in DRIVE. 11. Turn OFF the engine. 12. Turn the ignition switch to the unlocked OFF position. operable. If the ignition switch is not in the ON position, the shift will not take place and no position indicator lights will be on or flashing. Flashing NEUTRAL position indicator light indicates that shift requirements have not been met. 13. Shift the transmission into PARK. 14. Attach the vehicle to a tow vehicle with a tow bar. 15.
392 STARTING AND OPERATING 2. Reconnect the battery negative cable. 10. Set the parking brake. 3. Place the ignition switch in the LOCK position (if it has been moved or the engine has been started). 11. Shift the transmission into PARK. 4. Turn the ignition switch to the ON position, but do not start the engine. 5. Press the brake pedal. 6. Shift the transmission into NEUTRAL. 7. Use the point of a ballpoint pen or similar object to press the recessed transfer case NEUTRAL button.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 Hazard Warning Flasher . . . . . . . . . . . . . . . . 394 ▫ Spare Tire Removal . . . . . . . . . . . . . . . . . . . 396 䡵 If Your Engine Overheats . . . . . . . . . . . . . . . . 394 ▫ Preparations For Jacking . . . . . . . . . . . . . . . 397 䡵 Jacking And Tire Changing . . . . . . . . . . . . . . . 395 ▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . 398 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . 396 䡵 Jump-Starting . . . . . .
394 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The Hazard Warning flasher switch is located in the switch bank below the climate controls. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off the Hazard Warning flasher. This is an emergency warning system and it should not be used when the vehicle is in motion.
WHAT TO DO IN EMERGENCIES 395 NOTE: There are steps that you can take to slow down an impending overheat condition: JACKING AND TIRE CHANGING • If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine cooling system and turning the A/C can help remove this heat. WARNING! • You can also turn the Temperature Control to maximum heat, the Mode Control to floor and the Fan Control to high.
396 WHAT TO DO IN EMERGENCIES Jack Location The scissor-type jack and tire changing tools are located in the cargo compartment behind a trim cover on the left rear trim panel. The latch is located at the bottom of the trim cover. Jack Storage Location Spare Tire Stowage The spare tire is stowed underneath the rear of the vehicle and is held in place by a cable winch mechanism. Spare Tire Removal Fit the jack handle extension over the drive nut located in the rear cargo area inside the vehicle.
WHAT TO DO IN EMERGENCIES 397 When the spare is clear, tilt the retainer at the end of the cable, and pull it through the center of the wheel. Preparations For Jacking 1. Park the vehicle on a firm level surface as far from the edge of the roadway as possible. Avoid icy or slippery areas. WARNING! Lowering/Raising Spare Tire Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid being hit when operating the jack or changing the wheel.
398 WHAT TO DO IN EMERGENCIES 5. Turn on the Hazard Warning flasher. 6. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
WHAT TO DO IN EMERGENCIES 399 WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic. • To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. • Turn on the Hazard Warning flasher.
400 WHAT TO DO IN EMERGENCIES 4. Locate the jack as shown. For the front tires, place it (rearward) of the notch on the body weld seam behind wheel to be changed. For the rear tires, place it under the axle by the wheel to be changed. Position the jack handle on the jack. Do not raise the vehicle until you are sure the jack is fully engaged. Rear Jacking Location 5. Raise the vehicle by turning the jack screw to the right.
WHAT TO DO IN EMERGENCIES 401 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and install lug nuts with the cone-shaped end toward the wheel. Lightly tighten the nuts.
402 WHAT TO DO IN EMERGENCIES JUMP-STARTING WARNING! (Continued) WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be hurt by the fan. • Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic transmission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
WHAT TO DO IN EMERGENCIES 403 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach, but without allowing the vehicles to touch. 6. Connect the other cable, first to the negative terminal of the booster battery and then to the engine ground of the vehicle with the discharged battery. Make sure you have a good contact on the engine ground.
404 WHAT TO DO IN EMERGENCIES 7. If the vehicle is equipped with Sentry Key威 Immobilizer, turn the ignition switch to the ON position for three seconds before moving the ignition switch to the START position. 8. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 9. When removing the jumper cables, reverse the above sequence exactly. Be careful of the moving belts and fan.
WHAT TO DO IN EMERGENCIES 405 TOWING METHODS NOTE: When towing a 4x4 model, the transfer case must be in NEUTRAL and the transmission must be in PARK.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 3.7L . . . . . . . . . . . . . 409 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 415 䡵 Onboard Diagnostic System — OBD II . . . . . . 410 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . 416 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 410 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . 417 䡵 Emissions Inspection And Maintenance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . .
408 MAINTAINING YOUR VEHICLE ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . 423 䡵 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 447 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . 429 ▫ Headlight . . . . . . . . . . . . . . . . . . . . . . . . . . 447 ▫ Automatic Transmission . . . . . . . . . . . . . . . 430 ▫ Front Turn Signal And Front Side Marker Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448 ▫ Transfer Case . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 409 ENGINE COMPARTMENT — 3.
410 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
MAINTAINING YOUR VEHICLE 411 appear the next time the vehicle is started. This might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the MIL. Resolving the problem will turn the MIL light off. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system. Failure to pass could prevent vehicle registration.
412 MAINTAINING YOUR VEHICLE 5. Approximately 15 seconds later, one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition or start the engine. This means that your vehicle’s OBD II system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn OFF the ignition or start the engine.
MAINTAINING YOUR VEHICLE 413 your vehicle. Refer to these manuals before attempting any procedure yourself. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. WARNING! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
414 MAINTAINING YOUR VEHICLE dipstick. Adding 1 quart (0.9 L) of oil when the reading is at the bottom of the SAFE zone will result in a reading at the top of the safe zone on these engines. CAUTION! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.
MAINTAINING YOUR VEHICLE 415 Engine Oil Viscosity SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low temperature starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compartment” in this section.
416 MAINTAINING YOUR VEHICLE Engine Oil Filter Selection All of this manufacturer’s engines have a full-flow type disposable oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high-quality filters should be used to assure most efficient service. MOPAR威 engine oil filters are high-quality oil filters and are recommended. Engine Air Cleaner Filter Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals.
MAINTAINING YOUR VEHICLE 417 Maintenance-Free Battery The top of the maintenance-free battery is permanently sealed. You will never have to add water, nor is periodic maintenance required. WARNING! (Continued) • Battery posts, terminals, and related accessories contain lead and lead compounds. Wash hands after handling. WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing.
418 MAINTAINING YOUR VEHICLE CAUTION! (Continued) WARNING! • If a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery. Do not use a “fast charger” to provide starting voltage as battery damage can result. • Use only refrigerants and compressor lubricants approved by the manufacturer for your air conditioning system. Some unapproved refrigerants are flammable and can explode, injuring you.
MAINTAINING YOUR VEHICLE 419 Refrigerant Recovery and Recycling R-134a air conditioning refrigerant is a hydrofluorocarbon (HFC) that is endorsed by the Environmental Protection Agency and is an ozone-saving product. However, the manufacturer recommends that air conditioning service be performed by an authorized dealer or other service facilities using recovery and recycling equipment.
420 MAINTAINING YOUR VEHICLE Windshield Wiper Blades Clean the rubber edges of the wiper blades and the windshield periodically with a sponge or soft cloth and a mild non-abrasive cleaner or use the washer solvent. This will remove accumulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer fluid when using the wipers to remove salt or dirt from a dry windshield.
MAINTAINING YOUR VEHICLE 421 Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system or if the exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have an authorized technician inspect the complete exhaust system and adjacent body areas for broken, damaged, deteriorated, or mispositioned parts.
422 MAINTAINING YOUR VEHICLE CAUTION! WARNING! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the vehicle.
MAINTAINING YOUR VEHICLE 423 To minimize the possibility of catalytic converter damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the vehicle. • Do not idle the engine with any ignition coil connectors disconnected for prolonged periods. • Do not idle the engine for prolonged periods during very rough idle or malfunctioning operating conditions.
424 MAINTAINING YOUR VEHICLE spraying water from a garden hose vertically down the face of the A/C condenser (if equipped) or the back of the radiator core. Check the engine cooling system hoses for brittle rubber, cracking, tears, cuts, and tightness of the connection at the coolant recovery bottle and radiator. Inspect the entire system for leaks.
MAINTAINING YOUR VEHICLE 425 CAUTION! CAUTION! (Continued) • Mixing of engine coolant (antifreeze) other than specified HOAT engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. If a non-HOAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, it should be replaced with the specified engine coolant (antifreeze) as soon as possible. • Do not use water alone or alcohol-based engine coolant (antifreeze) products.
426 MAINTAINING YOUR VEHICLE When adding engine coolant (antifreeze): • The manufacturer recommends using MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology). Please note that it is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. • Mix a minimum solution of 50% HOAT engine coolant (antifreeze) and distilled water.
MAINTAINING YOUR VEHICLE 427 WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety precaution. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap while the system is hot or under pressure. • Do not use a pressure cap other than the one specified for your vehicle.
428 MAINTAINING YOUR VEHICLE the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional engine coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment.
MAINTAINING YOUR VEHICLE 429 • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory cooling performance, poor gas mileage, and increased emissions. Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals.
430 MAINTAINING YOUR VEHICLE WARNING! • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. • Use of a brake fluid that has a lower initial boiling point than the recommended product or a brake fluid that is unidentified as to FMVSS specification may result in sudden brake failure during hard prolonged braking. You could have an accident.
MAINTAINING YOUR VEHICLE 431 Fluid and Filter Changes Refer to the “Maintenance Schedule” in Section 8 for the proper maintenance intervals. In addition, change the fluid and filter if the transmission is disassembled for any reason. Special Additives The manufacturer strongly recommends against the addition of any additives to the transmission. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks.
432 MAINTAINING YOUR VEHICLE Draining Fluid First remove fill plug (2), then drain plug (3). Recommended tightening torque for drain and fill plugs is 15–25 ft lbs (20–34 N·m). CAUTION! Do not over-tighten the plugs. You could damage them and cause a leak. Lubricant Selection Use only manufacturer’s recommended fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type.
MAINTAINING YOUR VEHICLE 433 Sky Slider姞Top Care Immediate removal of any contaminant is recommended. Regular washing of the top will enhance its life and appearance, and make successive cleaning easier. Do not subject the top to excessive heat. Frequently vacuum the top and tracks. Periodically wipe dust and dirt from the top and inside of the tracks by hand with a window cleaner or alcohol dampened cloth. Washing Hand washing or an automatic car wash with a soft cloth system is preferred.
434 MAINTAINING YOUR VEHICLE • Allow the top to dry before opening. Vacuuming the top with a wet/dry shop vacuum will decrease the tops drying time, ensure removal of all dirt, and delete streaks in the material. • Multiple cleanings may be necessary to remove stubborn stains. If stains persist, contact your local authorized dealership for further suggestions. CAUTION! Never use an abrasive type cleaner or bleaches.
MAINTAINING YOUR VEHICLE 435 Weather Strip Care Lubricate the weather strips periodically with MOPAR威 Weather Strip Lubricant, to keep them soft and pliable. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. Appearance Care and Protection from Corrosion The most common causes are: Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geographic locations and usage.
436 MAINTAINING YOUR VEHICLE • If insects, tar, or other similar deposits have accumulated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover to remove. • Use MOPAR威 Cleaner Wax to remove road film, stains, and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
MAINTAINING YOUR VEHICLE 437 • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., assure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • Use MOPAR威 Touch Up Paint or equivalent on scratches or chips as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle.
438 MAINTAINING YOUR VEHICLE • For grease stains, apply MOPAR威 Multi-Purpose Cleaner to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue. Cleaning Leather Upholstery MOPAR威 Total Clean is specifically recommended for leather upholstery. • Do not use any solvents or protectants on Stain Repel products. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth.
MAINTAINING YOUR VEHICLE 439 WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
440 MAINTAINING YOUR VEHICLE 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft cloth. Seat Belt Maintenance Do not bleach, dye, or clean the seat belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric.
MAINTAINING YOUR VEHICLE 441 Cavity J1 J2 J3 J4 J5 J6 J7 Cartridge Fuse — 30 Amp Pink 40 Amp Green 25 Amp White 25 Amp White 40 Amp Green 30 Amp Pink MiniFuse — — Description — — Transfer Case Module - if equipped Rear Door Modules — Driver Door Node — Passenger Door Node — Anti-Lock Brake System (ABS) Pump/ESP - if equipped Anti-Lock Brake System (ABS) Valve/ESP - if equipped Cavity J8 J9 J10 J11 J13 J14 — J15 J17 Cartridge Fuse 40 Amp Green 40 Amp Green — — 60 Amp Yellow 40 Amp Green — 40
442 MAINTAINING YOUR VEHICLE Cavity J18 J19 Cartridge Fuse 20 Amp Blue M1 60 Amp Yellow 30 Amp Pink 20 Amp Blue 25 Amp White — M2 — J20 J21 J22 MiniFuse M3 M4 — Powertrain Control Module (PCM) Transmission Relay Radiator Fan Cartridge Fuse — — M5 — — Front Wiper M6 — — Front Washer/Rear Washer - if equipped Sunroof Module - if equipped Stop Light Switch Feed — Center High Mounted Stop Light (CHMSL) Trailer Lighting - if equipped M7 — M8 — M9 — — — 15 Amp Blue 20 Amp Yellow Desc
MAINTAINING YOUR VEHICLE 443 Cavity M10 Cartridge Fuse — M11 — 10 Amp Red M12 — M13 — 30 Amp Green 20 Amp Yellow M14 — MiniFuse Description 15 Amp Blue Hands-Free Module (HFM) – if equipped/ Universal Garage Door Opener (UGDO) – if equipped/Vanity Light Automatic Temperature Control (ATC) - if equipped Radio/Amplifier - if equipped Cabin Compartment Node (CCN)/Wireless Control Module (WCM)/ Multifunction Control Switch — — Cavity M15 Cartridge Fuse — M16 — M17 — MiniFuse Description
444 MAINTAINING YOUR VEHICLE Cavity M18 Cartridge Fuse — M19 — M20 — M21 — M22 — MiniFuse Description 15 Amp Blue Exterior Lighting — Right Front Park and Side Marker, Right Tail and Running Lights Auto Shut Down (ASD) #1 and #2 Interior Lighting/Steering Wheel Switches - if equipped/Switch Bank/ Electronic Vehicle Information Center (EVIC) - if equipped Auto Shut Down (ASD) #3 Right Horn (Hi/Low) 25 Amp Natural 15 Amp Blue 20 Amp Yellow 10 Amp Red Cavity M23 Cartridge Fuse — M25 — M26
MAINTAINING YOUR VEHICLE 445 Cavity M30 Cartridge Fuse — M31 — M32 — M33 — M34 — MiniFuse 15 Amp Blue 20 Amp Yellow 10 Amp Red 10 Amp Red 10 Amp Red Description Rear Wiper Module - if equipped/Diagnostic Link Back-Up Lights Occupant Restraint Controller (ORC) Powertrain Control Module (PCM) Park Assist Module - if equipped/Heating, Ventilation, and Air Conditioning (HVAC) Module - if equipped/Compass Module - if equipped Cavity M35 Cartridge Fuse — M36 M37 — — M38 — MiniFuse Description
446 MAINTAINING YOUR VEHICLE CAUTION! • When installing the Integrated Power Module cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the Integrated Power Module, and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload.
MAINTAINING YOUR VEHICLE 447 BULB REPLACEMENT Headlight 1. Open the hood. 2. Reach behind the headlight housing to access the headlight bulb lock ring. 3. Firmly grasp the lock ring and rotate it counterclockwise to unlock it. 4. Remove the bulb and connector assembly from the headlight housing. 5. Disconnect the bulb from the electrical connector and then connect the replacement bulb. CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life.
448 MAINTAINING YOUR VEHICLE Front Turn Signal and Front Side Marker Lights Front Fog Light 1. Turn the steering wheel all the way to the right to access the left front turn signal or side marker. Turn the steering wheel all the way to the left to access the right front turn signal or side marker. 1. Open the hood. 2. Remove three push-pins from the wheel-well liner. 3. Gently flex the wheel-well liner forward to access the bulb. 4.
MAINTAINING YOUR VEHICLE 449 6. Close the hood. 6. Separate the back plate from the taillight housing. Rear Tail/Stop, Turn Signal, and Back-Up Lights 7. Pull the appropriate bulb(s) out of the back plate and insert the replacement bulb(s). 1. Open the liftgate. 2. Remove the screws that fasten the taillight housing to the vehicle. 3. Pull the taillight housing straight back to separate it from the vehicle. 4. Disconnect the electrical connector. 5.
450 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Fuel (Approximate) 19.5 Gallons Engine Oil with Filter 3.7 Liter Engine (SAE 5W-20, API Certified) 5 Quarts Cooling System * 3.7 Liter Engine (MOPAR威 Antifreeze/Engine Coolant 5 Year/100,000 Mile Formula) 14 Quarts * Includes heater and coolant recovery bottle filled to MAX level. Metric 73.8 Liters 4.7 Liters 13.
MAINTAINING YOUR VEHICLE 451 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (3.7L Engine) Engine Oil Filter Spark Plugs (3.7L Engine) Fuel Selection (3.7L Engine) Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade.
452 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case Front Axle Rear Axle Brake Master Cylinder Power Steering Reservoir Fluid, Lubricant, or Genuine Part MOPAR威 ATF+4 Automatic Transmission Fluid MOPAR威 ATF+4 Automatic Transmission Fluid SAE 80W-90 Multi-Purpose Type, GL-5 Gear Lubricant or equivalent SAE 75W-140 Synthetic Gear Lubricant or equivalent MOPAR威 DOT 3 Brake Fluid, SAE J1703 should be used.
MAINTENANCE SCHEDULES CONTENTS 䡵 Emissions Control System Maintenance . . . . . . 454 䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 454 M A I N T E N A N C E S ▫ Required Maintenance Intervals . . . . . . . . . .
M A I N T E N A N C E 454 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type must be done at the times or mileages specified to ensure the continued proper functioning of the emissions control system. These and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
MAINTENANCE SCHEDULES 455 M NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicles oil if it has been six months since your last oil change even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-road for an extended period of time. • Under no circumstances should oil change intervals exceed 6,000 miles (10 000 km) or six months, whichever comes first.
M A I N T E N A N C E S C H E D U L E S 8 456 MAINTENANCE SCHEDULES • Check the fluid levels of coolant reservoir, brake master cylinder, and transmission and add as needed. CAUTION! • Check all lights and other electrical items for correct operation. Failure to perform the required maintenance items may result in damage to the vehicle. At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines.
MAINTENANCE SCHEDULES 457 M 6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the CV joints.
M 458 MAINTENANCE SCHEDULES A I N 18,000 Miles (30,000 km) or T 18 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Inspect the front and rear axle fluid; S C H E D U L E S change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule 30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter.
MAINTENANCE SCHEDULES 459 M 36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule 42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary.
M 460 MAINTENANCE SCHEDULES A I N 54,000 Miles (90,000 km) or T 54 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Inspect the front and rear axle fluid; S C H E D U L E S 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires.
MAINTENANCE SCHEDULES 461 M 66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule 72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary.
M 462 MAINTENANCE SCHEDULES A I N 78,000 Miles (130,000 km) or T 78 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E 84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary.
MAINTENANCE SCHEDULES 463 M 90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Inspect and replace PCV valve if necessary. † Replace the spark plugs (3.7L Engine). Adjust parking brake on vehicles equipped with four-wheel disc brakes. Inspect the transfer case fluid.
M 464 MAINTENANCE SCHEDULES A I N 102,000 Miles (170,000 km) or T 102 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ Flush and replace the engine coolant if S C H E D U L E S not done at 60 months. 108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule 114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires.
MAINTENANCE SCHEDULES 465 M 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the ignition cables (3.7L Engine). Replace the spark plugs (3.7L Engine). Inspect the brake linings; replace if necessary. Adjust parking brake on vehicles equipped with four-wheel disc brakes. Inspect the CV joints. Inspect exhaust system.
M 466 MAINTENANCE SCHEDULES A I N 132,000 Miles (220,000 km) or T 132 Months Maintenance E N Service Schedule A ❏ Change the engine oil and engine oil filter. N C ❏ Rotate tires. E ❏ If using your vehicle for any of the S C H E D U L E S 138,000 Miles (230,000 km) or 138 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary.
MAINTENANCE SCHEDULES 467 M 144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary. ❏ Inspect the brake linings; replace if necessary. ❏ Inspect the front and rear axle fluid; change if using your vehicle for police, taxi, fleet, off-road or frequent trailer towing. ❏ Inspect the CV joints.
M A I N T E N A N C E S C H E D U L E S 8 468 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 Suggestions For Obtaining Service For Your Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . 473 ▫ Prepare For The Appointment . . . . . . . . . . . 471 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . 473 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . 471 䡵 Warranty Information (U.S. Vehicles Only) . . . .
470 IF YOU NEED CONSUMER ASSISTANCE 䡵 Department Of Transportation Uniform Tire Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 476 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 477 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . 477 ▫ Temperature Grades . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 471 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager. Keep a maintenance log of your vehicle’s service history. This can often provide a clue to the current problem.
472 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealership. They want to know if you need assistance. • If an authorized dealership is unable to resolve the concern, you may contact the manufacturer’s customer center.
IF YOU NEED CONSUMER ASSISTANCE 473 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY.
474 IF YOU NEED CONSUMER ASSISTANCE the ownership experience. You’ll be pleased with their sincere efforts to resolve any warranty issues or related concerns. WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm.
IF YOU NEED CONSUMER ASSISTANCE 475 To contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
476 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Diagnostic Procedure Manuals are filled with diagrams, charts and detailed illustrations. These practical manuals make it easy for students and technicians to find and fix problems on computer-controlled vehicle systems and features. They show exactly how to find and correct problems the first time, using step-bystep troubleshooting and drivability procedures, proven diagnostic tests and a complete list of all tools and equipment.
IF YOU NEED CONSUMER ASSISTANCE 477 Treadwear The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
478 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
480 INDEX About Your Brakes . . . . . . . . . . . . . . . . . . . . . . . 320 ABS (Anti-Lock Brake System) . . . . . . . . . . . . 321,324 Adding Engine Coolant (Antifreeze) . . . . . . . . . . 425 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 370 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 368 Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 416 Air Conditioner Maintenance . . . . . . . . . . . . . . . 418 Air Conditioning . . . . . . . . . . . . . . . . . .
INDEX 481 Automatic Headlights . . . . . . . . . . . . . . . . . . . . 143 Automatic Oil Change Indicator . . . . . . . . . . 212,218 Automatic Temperature Control (ATC) . . . . . . . . . 277 Automatic Transaxle . . . . . . . . . . . . . . . . . . . . . . 294 Special Additives . . . . . . . . . . . . . . . . . . . . . . 431 Automatic Transmission . . . . . . . . . . . . . 296,430,431 Adding Fluid . . . . . . . . . . . . . . . . . . . . . . 431,452 Fluid and Filter Changes . . . . . . . . . . . . . .
482 INDEX Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 Brake/Transmission Interlock . . . . . . . . . . . . . . . 295 Break-In Recommendations, New Vehicle . . . . . . . . 80 Brightness, Interior Lights . . . . . . . . . . . . . . . . . . 148 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 446,447 Bulbs, Light . . . . . . . . . . . . . . . . . . . . . . . . . . 83,446 Calibration, Compass . . . . . . Capacities, Fluid . . . . . . . . . Caps, Filler Fuel . . . . . . .
INDEX 483 Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 274 Clock . . . . . . . . . . . . . . . . . . . . . . . . 229,243,246,255 Coin Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Cold Weather Operation . . . . . . . . . . . . . . . . . . . 291 Command-Trac Operation . . . . . . . . . . . . . . . . . . 302 Compact Disc (CD) Maintenance . . . . . . . . . . . . . 273 Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . . 350 Compass . . . . . . . . . . . . . .
484 INDEX Dimmer Switch, Headlight . . . . . . . . . . . . . . . . . 147 Dipsticks Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . . . 413 Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 319 Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . 427 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Door Locks, Automatic . . . . . . . . . . . . . . . . . . . .
INDEX 485 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . 416 Block Heater . . . . . . . . . . . . . . . . . . . . . . . . . 293 Break-In Recommendations . . . . . . . . . . . . . . . . 80 Checking Oil Level . . . . . . . . . . . . . . . . . . . . . 413 Compartment . . . . . . . . . . . . . . . . . . . . . . . . . 409 Coolant (Antifreeze) . . . . . . . . . . . . . . . . . 423,451 Cooling . . . . . . . . . . . . . . . .
486 INDEX Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 415,451 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . . 415 Finish Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435 Flashers Hazard Warning . . . . . . . . . . . . . . . . . . . . . . . 394 Turn Signal . . . . . . . . . . . . . . . . 83,146,205,448,449 Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Flipper Glass, Liftgate . . . . . . . . . . . . . . . . . . . . .
INDEX 487 Materials Added . . . . . . . . . . . . . . . . . . . . . . . 368 Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 Octane Rating . . . . . . . . . . . . . . . . . . . . . . 365,451 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 365 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 451 Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . 450 Fuel System Caution . . . . . . . . . . . . . . . . . . . . . 370 Fueling . . . . . . . . . . . .
488 INDEX Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 447 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439 Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 High Beam/Low Beam Select Switch . . . . . . . . 147 Lights On Reminder . . . . . . . . . . . . . . . . . . . . 145 On With Wipers . . . . . . . . . . . . . . . . . . . . 143,152 Passing . . . . . . . . . . . . . . . . . . . . .
INDEX 489 Instrument Panel Cover . . . . . . . . . . . . . . . . . . . 438 Instrument Panel Lens Cleaning . . . . . . . . . . . . . 439 Integrated Power Module (Fuses) . . . . . . . . . . . . 440 Interior Appearance Care . . . . . . . . . . . . . . . . . . 438 Interior Lighting . . . . . . . . . . . . . . . . . . . . . . 142,147 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Intermittent Wipers (Delay Wipers) . . . . . . . . . . . 150 Introduction . . . . . . . . . . . . . . . . .
490 INDEX Automatic Headlights . . . . . . . . . . . . . . . . . . . 143 Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449 Battery Saver . . . . . . . . . . . . . . . . . . . . . . . . . 148 Brake Assist Warning . . . . . . . . . . . . . . . . 208,336 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . 213 Bulb Replacement . . . . . . . . . . . . . . . . . . . 446,447 Cargo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 Courtesy/Reading . . . . . . . . . . . . .
INDEX 491 Rear Servicing . . . . . . . . . . . . . . . . . . . . . . . . 449 Rear Tail . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449 Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . 213 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . 446,447 Service Engine Soon (Malfunction Indicator) . . . 204 Side Marker . . . . . . . . . . . . . . . . . . . . . . . . . . 448 Tire Pressure Monitoring (TPMS) . . . . . . . . 202,356 Tow/Haul Indicator . . . . . . . . . . . . . . . .
492 INDEX Manual Transmission Lubricant Selection . . . . . . . . . . . . . . . . . . . . . 452 Map/Reading Lights . . . . . . . . . . . . . . . . . . . . . 147 Marker Lights, Side . . . . . . . . . . . . . . . . . . . . . . 448 Master Cylinder (Brakes) . . . . . . . . . . . . . . . . . . 429 Memory Feature (Memory Seat) . . . . . . . . . . . . . 136 Memory Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 Memory Seats and Radio . . . . . . . . . . . . . . . . . . 136 Methanol . . . . . . . .
INDEX 493 Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415,451 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . . 415 Identification Logo . . . . . . . . . . . . . . . . . . . . . 414 Materials Added to . . . . . . . . . . . . . . . . . . . . . 415 Recommendation . . . . . . . . . . . . . . . . . . . 414,450 Synthetic . . . . . . . . . .
494 INDEX Steering . . . . . . . . . . . . . . . . . . . . . . . . . . 318,319 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 Sunroof (Sky Slider) . . . . . . . . . . . . . . . . . 174,433 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Power Steering Fluid . . . . . . . . . . . . . . . . . . . . . 452 Pregnant Women and Seat Belts . . . . . . . . . . . . . . 52 Preparation for Jacking . . . . . . . . . . . . . . . . . . . . 397 Pretensioners Seat Belts . . . . .
INDEX 495 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . 16 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 412 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 352 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . 474 Resetting Oil Change Indicator . . . . . . . . . . . 212,218 Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . . . 131 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . . . 71 Restraints, Occupant . . . .
496 INDEX Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Easy Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . 131 Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 Height Adjustment . . . . . . . . . . . . . . . . . . . . . 130 Lumbar Support . . . . . . . . . . . . . . . . . . . . . . . 129 Memory . . . . . . . . .
INDEX 497 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451 Specifications Fuel (Gasoline) . . . . . . . . . . . . . . . . . . . . . . . . 451 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414,451 Speed Control (Cruise Control) . . . . . . . . . . . . . . 155 Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27,291 Cold Weather . . . . . . . . . . . . . . . . . . . . . . . . .
498 INDEX Theft Alarm (Security Alarm) . . . . . . . . . . . . . . . . 18 Theft System (Security Alarm) . . . . . . . . . . . . . . . 18 Tie Down Hooks, Cargo . . . . . . . . . . . . . . . . . . . 188 Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 154 Time Delay, Headlight . . . . . . . . . . . . . . . . . . . . 144 Tip Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 Tire and Loading Information Placard . . . . . . . . . 342 Tire Identification Number (TIN) . . . . . .
INDEX 499 Behind a Motor Home . . . . . . . . . Disabled Vehicle . . . . . . . . . . . . . . Guide . . . . . . . . . . . . . . . . . . . . . Recreational . . . . . . . . . . . . . . . . . Weight . . . . . . . . . . . . . . . . . . . . . Towing Assistance . . . . . . . . . . . . . . Towing Vehicle Behind a Motor Home Traction Control . . . . . . . . . . . . . . . . Trailer Sway Control (TSC) . . . . . . . . Trailer Towing . . . . . . . . . . . . . . . . . Cooling System Tips . . . . . . . . . . . Hitches .
500 INDEX Turn Signals . . . . . . . . . . . . . . . . 142,146,205,448,449 uconnect威 (Hands-Free Phone) . . . . . . . . . . . . . . . 94 Uniform Tire Quality Grades . . . . . . . . . . . . . . . . 476 Universal Transmitter . . . . . . . . . . . . . . . . . . . . . 165 Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . . 365 Untwisting Procedure, Seat Belt . . . . . . . . . . . . . . 48 Upholstery Care . . . . . . . . . . . . . . . . . . . . . . . . 438 Vanity Mirrors . . . . . . . . . . . . . .
INDEX 501 Windshield Wiper Blades Windshield Wipers . . . . . Wiper Blade Replacement Wiper, Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420 149 420 150 Wiper, Rear . . . . . . . Wipers, Intermittent . Wipers, Rain Sensitive Wrecker Towing . . . . ... ... .. ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION INTRODUCTION ROLLOVER WARNING HOW TO USE THIS MANUAL WARNINGS AND CAUTIONS VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS/ALTERATIONS THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key RemovalKey-In-Ignition ReminderSENTRY KEY Replacement KeysCustomer Key ProgrammingGeneral InformationVEHICLE SECURITY ALARM - IF EQUIPPED Rearming of the SystemTo Arm the SystemTo Disarm the System ILLUMINATED ENTRY SYSTEM REMOTE KEYLESS ENTRY (RKE) To Unlock the Doors and Liftga
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2009 LIBERTY LIBERTY 2009 owner’s manual Chrysler LLC 81-326-0941 Second Edition Printed in U.S.A.
