Third Party Verification Claim

Test Report
Number：
SHAH01476379
Tests Conducted
Page 2 of 17
INTERTEK TESTING SERVICES LTD.
ZHEJIANG
浙江天祥质量技术服务有限公司
Building No.2, Juanhu Science and Technology
Innovation Park, No. 500 East Shuiyueting Road,
Haining City, Zhejiang Province,China. 314400
中国浙江省海宁市水月亭东路 500 号鹃湖科技创新
园 2 幢 314400
Tel: [phone]
Zip:314400
www.intertek.com
www.intertek.com.cn
Safety Requirements and Test Methods for Outdoor Furniture
With reference to UL4041:2018 – Outline of investigation for outdoor furniture, the submitted sample was subjected to the following
tests:
Number of Sample Tested: One (1) Piece
Types: Chair type III
Overall dimensions: 740 mm W X 832 mm D X 910 mm H
Weight: 15.3 kg
Initial check: No visible damage was found.
Executive summary:
Clause Test item Verdict
Introduction
1 Scope
--
2 General
--
3 Glossary
--
Construction
4 General --
4.1
Furniture for outdoor use shall be constructed of materials and fasteners suitable for the purpose. P
4.2
Iron and steel units and components shall be protected against corrosion as specified in Protection
against Corrosion, Section 5.
P
4.3
Glass components shall meet the requirements of the Standard Performance Specifications and
Methods of Test for Safety Glazing Material Used in Buildings, ANSI Z97.1, Class A or shall not
break when tested according to EN 14072:2003, or shall break as specified in EN 14072:2003,
Clause 7, (c)(2) or (c)(3) or fulfils the requirements in EN 12150-1:2015, Clause 8, “Fragmentation
test”. If compliance to these standards is not met then Horizontal Glass Impact Test, Section 8 and
Vertical Glass Impact Test, Section 9 tests shall be conducted.
NA
4.4
Holes for umbrella in glass table top shall be protected to prevent metal to glass contact. NA
4.5
Plastics components that are deemed safety critical need to meet the outdoor requirements as
defined by a F1 rating, per Standard for Polymeric Materials – Use in Electrical Equipment
Evaluations, UL 746C.
NA
4.6
In order to avoid physical injury when the product is in its intended position of use, all edges and
corners shall be rounded, chamfered or otherwise protected. This applies to:
a) Seating: Edges of the seat, backrest and arm rests and any part of the bottom surface of the
seat at a distance less than 120 mm (4.7 in) from any edge, where the probe, see Figure 4.1
can commonly access;
b) Tables: Table tops, any part of the underside of the top surface at a distance less than 500 mm
(19.7 in) from any edge below the table, where a knee and/or an arm can commonly access.
P
4.7
All other parts shall be free from burrs, sharp edges and sharp points and shall comply with Standard
for Tests for Sharpness of Edges on Equipment, UL 1439.
P
4.8
Movable and adjustable parts shall be designed so that injuries and inadvertent operation are
avoided.
P
4.9
It shall not be possible for any load bearing part of the furniture to come loose unintentionally. P
4.10
All parts which are lubricated to assist sliding shall be designed to protect users from lubricant stains
when in normal use.
NA
4.11
There shall be no accessible holes in the ends of tubular components with a diameter between 7 mm
(0.28 in.) to 12 mm (0.47 in.) with a depth more or equal to 10 mm (0.39 in.). The bottom of tubular
legs in contact with the floor shall be closed or capped, however, holes in them are allowed as long
as they are not between 7 and 12 mm as this poses a potential finger entrapment issue.
P