User's Manual

ManualsBrandsJCM Technologies ManualsElectronicsTransceiver for Automatic Door Safety Edges Relay Output

www.milleredge.com info@milleredge.com 800-220-3343

INSTALLATION INSTRUCTIONS

Model: RB-G-K10

IMPORTANT: THIS DEVICE MUST BE PROFESSIONALLY INSTALLED.

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION.

The Miller Edge RBand Monitored Gate Edge Transmitter/Receiver system is intended to provide a wireless

connection between a monitored sensing edge and a motorized operator that controls the associated gate. RBand

meets the 2016 UL 325 requirements for monitored devices and has been certiﬁed as a UL 325 Recognized

Component. It is designed for use with operators that comply with 2016 UL 325 using a Miller Edge 10K Sensing

Edge.

1. PARTS LIST

Kit Contents:

1. RBand Edge Transmitter (RB-TX10)

2. RBand Gate Edge Receiver (RB-G-RX10)

3. Receiver antenna

4. (2) 3.6V AA lithium batteries*

5. (4) #6 pan head transmitter mounting screws

*Replacement 3.6V AA lithium batteries can be

purchased at your local electronics store or via

Miller Edge.

Required:

• 1/8” ﬂat blade screwdriver

• 1/4” ﬂat blade screwdriver

• Miller Edge 10K (T2/blue band) Sensing Edge

• Coaxial cable for exterior mounted antenna

• Coaxial bulkhead adapter, female/female

Recommended:

• Multi-meter capable of reading 10KΩ

• Mounting screws for the Receiver

2. RECEIVER: INSTALLATION

2-1. Remove operator cover and turn off the power to the gate operator.

2-2. Determine where to place the external mounted antenna so it is in line of sight with the Transmitter for the

entire range of travel [IMAGE 1]. Prepare the antenna coax as necessary.

2-3. Remove Receiver cover and mount the base inside the operator, positioning it for optimum ease of wiring.

2-4. Connect power to the terminals marked 12/24 AC/DC (polarity sensitive) on the removable 8-pin

connector [IMAGE 2].

2-5. Determine which monitored interface your operator uses. Connect the COM (C1/C2) and the correct output

connections (N.C. = CS1/CS2 or 10K = BS1/BS2) to your operator. There are 2 separate relays (channels):

R1 and R2. The A Test terminals must be used for operators requiring N.C. inputs. Enable with DIP switch 4

[TABLE 1].

2-6. Replace the Receiver cover and turn on power to the operator. Note: it takes ~5 seconds for the Receiver to

initialize.

Note: RBand 10K Gate Edge Receiver is compatible with up to 3 RBand Transmitters on 2 channels (6 total).

RB-G-K10_Install_A4_20170706

IMAGE 1. RBand Transmitter Installation with Gate Edge

RBAND RECEIVER

MOUNTED INSIDE OPERATOR

WITH EXTERNAL ANTENNA

OPERATOR

ANTENNA

WIRING

RBAND TRANSMITTER

MOUNTED NEAR

SENSING EDGE

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Model: RB-G-K10 IMPORTANT: THIS DEVICE MUST BE PROFESSIONALLY INSTALLED. READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION. The Miller Edge RBand Monitored Gate Edge Transmitter/Receiver system is intended to provide a wireless connection between a monitored sensing edge and a motorized operator that controls the associated gate. RBand meets the 2016 UL 325 requirements for monitored devices and has been certified as a UL 325 Recognized Component.
PAGE 2
LED INDICATORS Initial Power • No Transmitters Programmed: R1 & R2 LEDs on COAXIAL CABLE PROVIDED BY INSTALLER R1 or R2 LED • Programmed: Off • Fault Condition: On R3 LED • On when battery is low A TEST LED • On when in test mode F-CONNECTOR COAX EXTENDER ANTENNA ANTENNA CHECK LED TERMINAL & BUTTON BLOCK RELAY LEDS PROGRAM BUTTON CHECK LED (both channels programed) • Programmed: Check LED flashes every 5 seconds DIP SWITCH SETTINGS ON 1 2 3 4 Switch 1-3: Leave switches in factory default settings S
PAGE 3
PROGRAM BUTTON (2) 3.6V AA LITHIUM BATTERIES GREEN LED ALIGNMENT PIN ALIGNMENT PIN REMOVABLE SENSING EDGE TERMINAL BLOCK (4) CORNER MOUNTING HOLES STRAIN RELIEF FITTING IMAGE 3. RBand Edge Transmitter PCB & Connections 3. TRANSMITTER: PROGRAM MODE 3-1. Confirm the Receiver is powered up. Prior to mounting the Transmitter, remove the cover and insert the batteries, noting their polarity.
PAGE 4
7. RECEIVER: SPECIFICATIONS & CONTROLS Power: 12-24 VAC/DC nominal (11-30 V max); 100 mA max current draw. Power may be supplied from the operator or alternatively from an external supply. Dimensions: 4.12”L x 3.65”W x 1.65”H Dimensions: 4.12”L x 3.65”W x 1.
PAGE 5
NORMALLY CLOSED ADDENDUM: Removable Connector Assignments by Manufacturer All-O-Matic ON COMMON MON-12 VDC COMMON MON_OPEN COMMON GROUND MON_CLOSE +12 or 24 VDC + - CS1 C1 BS1 CS2 C2 BS2 NO3 C3 12/24 AC/DC COM.A TEST HySecurity 1 2 3 4 DIP Switch #4 • Turn to on ON +24 VDC SENSOR COM S1, S2, S3 SENSOR COM SENSOR COM S1, S2, S3 +24 VDC COMMON* + - CS1 C1 BS1 CS2 C2 BS2 NO3 C3 12/24 AC/DC COM.