Installation Guide

www.milleredge.com [e-mail] 800-220-3343
7. RECEIVER: SPECIFICATIONS & CONTROLS (cont.)
Power: 12-24 VAC/DC nominal (11-30 V max); 100 mA max current draw. Power may be supplied from the operator or alternatively from an
external supply.
Dimensions: 4.12”L x 3.65”W x 1.65”H
Cable Connections: Screw clamp type terminal blocks for 18-26 AWG wire
Operator Wiring: Screw clamp type terminal blocks for 18-26 AWG wire
External Antenna: F-connector coax extender for antenna
Program Button: Used to associate a Transmitter with the desired receiver channel
Check Button: Used to determine signal strength
RX Indicator Lights:
• Check LED:
1. After check button is pressed, blinks to indicate signal strength; 4 or 5 blinks is ideal
• R1 and R2 LEDs:
1. Off when the associated edge is learned and has no faults
2. On solid: No Transmitters learned or edge activated
• R3 LED: On when low battery relay is active
• A TEST LED: On in test mode. Not used.
Connections:
• Power (2): Positive and ground, or AC
• Relay Output 1:
1. CS1: Not used
2. C1: 10K monitored input common
3. BS1: 10K monitored input
• Relay Output 2: Not used
• Relay Output 3 (2): Relay closes when low battery is detected
• A TEST (2): Not used
8. TRANSMITTER: SPECIFICATIONS & CONTROLS
Transmitter Frequency: 916 MHz, FSK modulation
Mounting: 4 corner screws (provided)
Power Source: Batteries: 2 AA, 3.6V lithium, 2 year life expectancy
Dimensions: 1.80”L x 4.78”W x 1.75”H
Program Button: Momentary push button is used to associate the Transmitter to the Receiver
TX Indicator Lights:
• Green LED: Normally off
• Press program button for status
9. FCC COMPLIANCE
RBand Transmitter
Model: RB-TX10
FCC ID: U5Z-RB-TX10
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including
interference that may cause undesired operation.
This device complies with FCC radiation exposure limits for an
uncontrolled environment. This device shall be installed and operated
with a minimum distance of 0.4” between users or bystanders and
the device.
RBand Receiver
Model: RB-D-RX10
FCC ID: U5Z-RB-D-RX10
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including
interference that may cause undesired operation.
This device complies with FCC radiation exposure limits for an
uncontrolled environment. This device shall be installed and operated
with a minimum distance of 0.8” between users or bystanders and
the device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules:
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Re-orient or relocate the receiver antenna
2. Increase the separation between the equipment and the receiver
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
4. Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.