Operating Instructions

ManualsBrandsjc-2 ManualsControllersgame controller

XXXX Bluetooth Switch handle NFC with wake-up function (standard version)

Operating instructions V1.1 (2021-2-20)

1. Bluetooth pairing mode

Use USB to plug in the cable for the first time (boot), and then directly press the HOME

button to connect back, or press and hold the independent pairing button for 3 seconds

to enter the Bluetooth pairing mode, and the LED1-LED4 marquee flashes quickly.

Automatically identify the SWITCH host. After the connection is successful, the

corresponding channel indicator LED is always on (assigned by the Switch host).

Automatically recognize the PC platform, LED1 will be on after the connection is

successful;

If the STEAM platform is installed on the PC (Steam is in the switch mode), the LED will

follow the Steam platform allocation instructions.

If the pairing is unsuccessful within 2.5 minutes, the handle will automatically sleep.

2. Reconnect mode

Short press the handle HOME key or other number keys to wake up the handle,

LED1-LED4 marquee flashes, automatically connect to the previously paired host, and

automatically go to sleep if the connection is unsuccessful within 10 seconds.

If the SWITCH host is in sleep mode (not in airplane mode), press the HOME button to

wake up the host.

3. Charging instructions

When the handle is turned off, LED4 flashes slowly when charging, and LED4 is always

on when it is full;

Low battery voltage alarm: the current indicator flashes (fast flash);

When charging, the current channel indicator flashes (slowly flashing), and the current

indicator is always on when fully charged;

When pairing, reconnect charging or low battery, pairing, reconnect LED indication

takes priority.

4. Automatic sleep

The host screen is turned off, and the handle automatically sleeps

If no button is pressed within 5 minutes, it will automatically go to sleep (including the

sensor does not move). (Time can be adjusted according to needs)

In Bluetooth mode, press the HOME button for 3 seconds to disconnect the host, and

Summary of content (5 pages)

PAGE 1
XXXX Bluetooth Switch handle NFC with wake-up function (standard version) Operating instructions V1.1 (2021-2-20) 1. Bluetooth pairing mode Use USB to plug in the cable for the first time (boot), and then directly press the HOME button to connect back, or press and hold the independent pairing button for 3 seconds to enter the Bluetooth pairing mode, and the LED1-LED4 marquee flashes quickly. Automatically identify the SWITCH host.
PAGE 2
the handle sleeps. (Time can be adjusted according to needs) 5. Low voltage alarm If the voltage of the lithium battery is lower than 3.55V±0.1V, the current channel light flashes quickly to indicate that the voltage is low; (the voltage can be adjusted according to requirements) If the voltage of the lithium battery is lower than 3.45V±0.1V, it will automatically sleep; (the voltage can be adjusted according to requirements) 6.
PAGE 3
Automatically recognize the Switch platform, PC platform, and Android platform. Under the PC platform, it is automatically recognized as X-INPUT mode by default, and LED1+LED4 is on You can press and hold the'+' key and the'-' key for 3 seconds to switch the D-INPUT mode. Note: When the USB cable is inserted, the Bluetooth will be cut off. When the USB cable is unplugged, the handle will automatically reconnect 9.
PAGE 4
mode. A. Turn on the mode to recognize the 3D and A B X Y button LED lights, (3D is blue light) B. Click the light button: turn on the joystick LED (blue) and the A B X Y button LED; C. Click the light button again: the color of the joystick LED light changes, and click to change a color; sequence: blue, red, green, yellow, cyan, orange, purple, pink, illusion, cycle change; Abxy lights remain unchanged ( (The left and right joysticks change synchronously) D.
PAGE 5
WRNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.