Venue Sub10 (120V) OM 2/3/06 11:39 AM Page 3 ® JBL VENUE™ SUB10 (120V) OWNER’S GUIDE
Venue Sub10 (120V) OM 2/3/06 11:39 AM Page 4 READ FIRST! Important Safety Precautions! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. CAUTION: To prevent electric shock, do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.
Venue Sub10 (120V) OM 2/3/06 11:39 AM Page 5 INTRODUCTION JBL® SUB10 Powered Subwoofer For more than 60 years, JBL has been providing audio equipment to concert halls, recording studios and movie theaters around the world, and has become the hands-down choice of leading recording artists and sound engineers. SUB RIGHTCHANNEL SPEAKER With the JBL Venue™ Series, innovative technologies such as titaniumlaminate-dome tweeters, EOS™ waveguides and PolyPlas™ transducer reinforcement are available to you.
Venue Sub10 (120V) OM 2/3/06 11:39 AM Page 6 SPEAKER LEVEL IN LINE LEVEL IN 1 0 L LFE 4 3 GREEN: ON RED: STAND-BY SUBWOOFER LEVEL CROSSOVER R L PHASE 2 AUTO ON R MIN ® 180 7 0 50 MAX 5 "WAR NING : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE T 3.15A L/250V FUSE" ™ 0 0 Hz 150 6 T3.15A L/250V "AVE R TIS S E ME NT: UTILISEZ UN FUSIBLE DE RECHANGE DE MEME TYPE T 3.15A L/250V" SUB10 POWER ® 8 R C A UT IO N NRTL/C CSA 22-2 No.
Venue Sub10 (120V) OM 2/3/06 11:39 AM Page 7 SYSTEM CONNECTIONS If you have a Dolby® Digital or DTS® receiver/processor with a low-frequencyeffects (LFE) or subwoofer output: If your receiver/processor does not have subwoofer outputs for the left and right channels or an LFE output, connect speaker wire from your receiver/ amplifier to your speakers and subwoofer using two sets of speaker wire: SUBWOOFER OR LFE OUTPUT RECEIVER/AMPLIFIER Front Speaker Output IN ANDBY L R 0 0 IN L "W ARNING :F
Venue Sub10 (120V) OM 2/3/06 11:39 AM Page 8 OPERATION MAINTENANCE AND SERVICE Power On Plug your subwoofer’s AC cord into a wall outlet. Do not use the outlets on the back of the receiver. Initially set the Subwoofer-Level Control ¢ to the “min” position. The enclosure may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. Turn on your sub by pressing the Power Switch ª on the rear panel. All wiring connections should be inspected and cleaned or remade periodically.
Venue Sub10 (120V) OM 2/3/06 11:39 AM Page 9 SPECIFICATIONS SUB10 Frequency Response 27Hz – 150Hz Amplifier RMS Power 150 Watts Amplifier Peak Dynamic Power† 300 Watts Crossover Frequencies 50Hz – 150Hz, 24dB/octave, continuously variable Driver 10" (250mm) PolyPlas™ Dimensions (H x W x D) (with grille) 17-3/4" x 12-1/4" x 15-3/4" (451mm x 311mm x 400mm) Weight 32.1 lb (14.
Venue Sub10 (120V) OM 2/3/06 11:39 AM Page 2 All features and specifications are subject to change without notice. JBL and Harman International are registered trademarks, and Venue Series, EOS, PolyPlas and Pro Sound Comes Home are trademarks, of Harman International Industries, Incorporated. Dolby is a registered trademark of Dolby Laboratories. DTS is a registered trademark of DTS, Inc.
