LSR6325P ed Studio Monitor System Owner’s Manual
Important Safety Instructions The IEC fuse symbol pictured at the left represents an approved, user replaceable fuse. When replacing a fuse, make sure to replace with only the correct type and fuse rating. 1. Read lnstructions - Before operating your new JBL product, please read all safety and operating instructions. 2. Keep these instructions - For future reference and troubleshooting purposes, retain these instructions. 3. Heed all warnings - All warnings in this user manual should be followed. 4.
Explanation of Graphic Symbols The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
Table of Contents Important Safety Instructions ................................................................................... 2-3 Table of Contents ........................................................................................................................ 4 Introduction LSR6325P Features ................................................................................................... 5-6 Front Panel Drawing ................................................................................
Introduction Congratulations on your purchase of the LSR6325P Bi-Amplifi ed Studio Monitor, the newest member of the LSR6300 Series product line. The LSR6325P system incorporates patented JBL transducer and system technologies designed to provide ultra-accurate response and exceptional SPL capability in a very compact form-factor.
LSR6325P Features to Tackle the Problems in the Room LSR – Linear Spatial Reference Technology JBL Developed Linear Spatial Reference Technology to optimize mid and high frequency accuracy at the listening position where relected sound comes into play. Meeting frequency response criteria for seventy-two off-axis measurements, the LSR6325P ensures that not just the direct sound, but reflected sound that reaches you at the listening position is also smooth and accurate.
CB CBCBCBBB
Audio Connections The LSR6325P includes one XLR and one RCA connector to accommodate a wide range of signal levels and balanced or unbalanced configurations. The XLR input is nominal +4 dBu sensitivity and the RCA input is -10 dBV. Variable user calibration is provided using the front panel volume control. Positive voltage applied to pin 2 of the XLR or the pin of the RCA jack will produce a forward motion in the cone of the low frequency transducer.
Switch 3 boosts the high frequency response by 1.5 dB above 2.3 kHz when set to the UP position. This position can be used if the room is extremely dead, or you want to hear more high frequency from the speaker to assist you in creating “warmer” mixes. Switch 4 attenuates the high frequency response by 1.5 dB above 2.3 kHz when set in the UP position.
Caution: Unsafe mounting or overhead suspension of any heavy load can result in serious injury and equipment damage. Mounting of speakers should be done by qualified persons in accordance with all applicable local safety and construction standards. Be certain to follow the instructions provided by the manufacturer of the mounting bracket. Be certain that it is capable of supporting the weight of the speaker to be mounted.
Specifications System: Frequency Response (+1, -2 dB): 70 Hz – 20 kHz Enclosure Resonance Frequency: 55 Hz Low Frequency Extension: User controls set to default -3 dB: 65 Hz -6 dB: 56 Hz -10 dB: 48 Hz Low – High Frequency Crossover: 2.3 kHz 4th – Order Electroacoustic Linkwitz – Riley Distortion, 96 dB SPL, 1 m: Mid – High Frequency (150 Hz – 20 kHz): 2nd Harmonic: <0.5% 3rd Harmonic: <0.
THD+N, 1/2 power: <0.05% High Frequency: Topology: Class A-B, Monolithic Sine Wave Power Rating: 50 watts (<0.1% THD into rated impedance) THD+1/2 power: <0.05% Long Term Maximum System Power: 110 Watts (IEC 265-5) Transducers: Low Frequency Diameter: 134 mm (5.25 in.) Voice Coil: 38 mm (1.5 in.) Magnet Type: Ferrite with Integral Shielding Cone Type: Tempered Paper with Buty Rubber Surround Nominal Impedance: 8 ohm High Frequency Diameter: 25 mm (1 in.) diaphragm Voice Coil: 25 mm (1 in.
100 200 100 -100 SP L Phase 0 90 -200 80 -400 -300 dB -500 -600 70 -700 -800 -900 60 20 100 Frequency 1000 Hz -1000 10000 20K 13
Appendix: Wiring Recommendations For optimum performance, some attention to wiring details can reduce system degradation. If you notice hum present in the system when no audio signal is present, the following wiring recommendations can help. Balanced Sources – The best way to run your system is balanced, where both “HOT” (+) and “COLD” (-) signals are supplied, as well as a GROUND/SHIELD. These are typically carried on two conductor shielded cables with XLR connectors on both ends.
Diagram C Diagram D and E are similar. In Diagram E, a link is added between Pin 3 and Pin 2 of the XLR connector. In some cases, this could be required if hum is encountered.
Warranty Statement Who Is Protected by This Warranty? Your JBL Warranty protects the original owner and all subsequent owners so long as: A.) Your JBL product has been purchased in the Continental United States, Hawaii or Alaska. (This Warranty does not apply to JBL products purchased elsewhere except for purchases through military outlets. Other purchasers should contact the local JBL distributor for warranty information.); and B.
JBL Professional Contact Information Mailing Address: JBL Professional 8500 Balboa Blvd. Northridge, CA 91329 Outside the U.S.A. Contact the JBL Professional Distributor in your area. A complete list of JBL Professional International Distributors is provided at our U.S.A. web site - www.jblpro.com Shipping Address: JBL Professional 8370 Balboa Blvd., Dock D Northridge, CA 91329 En Dehors des Etats-Unis: Contacter votre Distributeur JBL Professional.
JBL Professional 8500 Balboa Boulevard P. O.Box 2200 Northridge, California 91329 U.S.A. www.jblpro.
