User's Guide
CONTENTS Safety Instructions................................................................................................................................................ 4 Precautions........................................................................................................................................................... 6 Declaration of Conformity......................................................................................................................................
SAFETY INSTRUCTIONS The EON700 system covered by this manual is not intended for use in high moisture environments. Moisture can damage the speaker cone and surround and cause corrosion of electrical contacts and metal parts. Avoid exposing the speakers to direct moisture. Keep speakers out of extended or intense direct sunlight. The driver suspension will prematurely dry out and finished surfaces may be degraded by long-term exposure to intense ultra-violet (UV) light.
1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings. 4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. 7. DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
PRECAUTIONS WARNING: This product is intended to be operated ONLY from the voltages listed on the back panel. Operation from other voltages other than those indicated may cause irreversible damage to the product and void the product’s warranty. The use of AC Plug Adapters is cautioned because it can allow the product to be plugged into voltages in which the product was not designed to operate. If you are unsure of the correct operational voltage, please contact your local distributor and/or retailer.
DECLARATION OF CONFORMITY WIRELESS TRANSMITTER COMPLIANCE INFORMATION: The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. Le terme «IC:» avant le numero de certification radio signifie seulement que les specifications techniques d’lndustrie Canada ont ete respectees. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
INTRO TO EON700 GETTING STARTED Congratulations on your purchase of JBL Professional EON700 loudspeakers! We know you are anxious to get up and running as fast as possible, which is why you are reading this section. The following will help you get set up as soon as possible. Packaging Contents Your EON700 should include: • 1 EON700 Full Range or Subwoofer Cabinet • 1 6’ (2m) AC Power Cable • 1 QSG Unboxing 1. Open packaging 2.
OVERVIEW SETTING UP How to set up 1. Insert input into desired channel 2. Slowly turn the Main knob to increase your main volume. 3. Adjust the Channel Gain knobs until your desired volume is achieved. How to turn on/off Press the Power Button for .5 of a second to engage power. P.A. BASICS A mixing board is actually a very simple device that takes the audio input signals (from the input channels) and “mixes” them to the outputs.
LOUDSPEAKER PLACEMENT AND SUSPENSION The following guidelines will help you achieve optimum sound wherever you use your EON700® loudspeakers: Only experienced professionals should attempt to suspend the speakers. For permanent installation applications utilizing the M10 suspension points, JBL Professional recommends the use of three (3) M10 x 1.5 thread pitch forged shoulder steel eyebolts with an 18-20mm threaded shaft, along with fender washers, rated for overhead suspension.
APPLICATION EXAMPLES MICROPHONE (presenter or speaker) >1m positioning distance >2m Microphone (speaker/presenter) To prevent any unnecessary feedback, please: Position Microphone at least 2m (6ft) from a speaker Do not stand directly in front of a speaker © 2021 HARMAN Professional Denmark ApS PROPRIETARY AND CONFIDENTIAL PROPERTY OF HARMAN. DO NOT DISCLOSE, REPRODUCE, OR PUBLISH WITHOUT WRITTEN HARMAN APPROVAL.
USING TWO SYSTEMS AS MAINS EON700 Left and EON700 Right 12
MIXER PANEL LCD Panel CH 1 & CH 2 Signal Clip LED CH 1 & CH 2 Gain A B Power C Main Volume / Menu Navigation D Limit LED E Back Button K J G H I XLR Male Loop Thru CH 2 XLR-1/4” Combo CH 1 XLR-1/4” Combo Input F AC Power Connector 13
MIXER PANEL FUNCTIONS A. LCD Panel The LCD is used to display basic diagnostic information and allow access to more advanced features through a menu system. See the LCD GUI specification for more details on the LCD menu system, features, and navigation. The LCD will refresh at approximately 4Hz and is not suitable for meters or any other fast motion items. B. Power Button The Power Button is a momentary push button. It is used to toggle the unit between the On and Off states.
Knobs and Functions The EON700 comes equipped with push button rotaries to make for easy navigation and hardware usage. • A single press of the MAIN/MENU knob will open up the main menu. • Pressing and holding the MAIN/MENU knob for 2s will mute the SPEAKER. • Pressing and holding a CHANNEL KNOB for 2s will mute the CHANNEL. Buttons and Functions • The POWER button turns on/off the speaker. Hold for .5s to turn on the speaker and .5s to turn off the speaker.
EASYNAV LCD Intro to the EasyNav LCD Main Menu • Pressing the Main/Menu rotary at any time will take you to the EON700’s main menu. Here, users can access the main menu functions of the EON700. • Gain adds preamp gain to the system to support microphone usage. EON700’s fader runs standard in LINE LEVEL, but accessing the GAIN menu can allow users to plug a microphone in directly. • • Press MAIN/MENU to access the GAIN menu.
• • Turn the knob CLOCKWISE to activate that channel as a SENSOR for ducking. When this is selected, the respective channel will detect signal and activate the ducking feature on the Bluetooth signal. • Turn the knob COUNTER-CLOCKWISE to disable that channel as a SENSOR for ducking. When this is disabled, signal detection on this channel will NOT trigger the ducking feature on the Bluetooth signal.
the following position standards on stage: • • Microphones should be behind the front plane of the speakers. • Microphones should be least two meters to the left or right of the speakers. • “AFS by dbx” On/Off selection toggles the AFS processor on or off. • “Reset Filters” will reset all filters, prompting the filters to reset and start over in their discovery of potential feedback frequency risks.
• • “HPF on this Speaker” can be used to remove signal below a selected frequency to the built-in amp/speaker and tweeter bar. • “LFP on Pass Thru Out” can be used to set the low pass filter on the Thru Out XLR output feed. Time Align • Signal delays are used when multiple speakers are in use but speakers are at different distances from the audience. • Examples: • • A subwoofer is front of the stage, while this full range speaker in on the stage.
APP JBL Pro Connect The JBL Pro Connect app is a Bluetooth Low Energy control application used to remotely control the features within the EON700. The app is a free download on iOS and Android. It is recommended that all users download the app and ensure their unit is operating on the latest firmware for the best experience.
EON710 SPECIFICATIONS TECHNICAL SPECIFICATIONS System Type 10IN Powered Loudspeaker Woofer Model 710G Woofer Size 10" Woofer Magnet Ferrite Woofer Voice Coil 2" Tweeter Model 2414H Compression Driver Tweeter Size 1" Tweeter Magnet Neodymium Transducer Impedence LF 4ohm rated, HF 8ohm rated Max SPL 125dB @1m/4Pi Freq Range -10 52Hz - 20kHz Freq Range -3 65Hz - 20kHz Hor Dispersion 110° Vert Dispersion 60° Power Rating 1300W peak / 650 RMS AC Power Input 100V-120V or 220V-240V
EON712 SPECIFICATIONS TECHNICAL SPECIFICATIONS System Type 12IN Powered Loudspeaker Woofer Model 712G Woofer Size 12" Woofer Magnet Ferrite Woofer Voice Coil 2" Tweeter Model 2414H Compression Driver Tweeter Size 1'' Tweeter Magnet Neodymium Transducer Impedence LF 4ohm rated, HF 8ohm rated Max SPL 127dB @1m/4Pi Freq Range -10 50Hz - 20kHz Freq Range -3 60Hz - 20kHz Hor Dispersion 100° Vert Dispersion 60° Power Rating 1300W peak / 650 RMS AC Power Input 100V-120V or 220V-240V
EON715 SPECIFICATIONS TECHNICAL SPECIFICATIONS System Type 15IN Powered Loudspeaker Woofer Model 715G Woofer Size 15" Woofer Magnet Ferrite Woofer Voice Coil 2" Tweeter Model 2414H Compression Driver Tweeter Size 1'' Tweeter Magnet Neodymium Transducer Impedence LF 4ohm rated, HF 8ohm rated Max SPL 128dB @1m/4Pi Freq Range -10 45Hz - 20kHz Freq Range -3 55Hz - 20kHz Hor Dispersion 90° Vert Dispersion 60° Power Rating 1300W peak / 650 RMS AC Power Input 100V-120V or 220V-240V
EON718S SPECIFICATIONS TECHNICAL SPECIFICATIONS System Type 18IN Powered Subwoofer Woofer Model 718G Woofer Size 18" Woofer Magnet Ferrite Woofer Voice Coil 3" Transducer Impedence 4 ohm rated Max SPL 131dB @1m/2Pi Freq Range -10 31Hz - 150Hz Freq Range -3 40Hz -120Hz Hor Dispersion Omni Vert Dispersion Omni Crossover Frequency 80, 100, 120hZ selectable Power Rating 1500W / 750W RMS AC Power Input 100V-120V or 220V-240V Cooling Passive LED Indicators 1 Power LED, 1 System Limi
CABLES & CONNECTORS XLR/F to XLR/M Microphone Cable The standard cable for interconnection of microphone and line level signal in professional audio systems. • Microphone to mixer TRS (balanced) 1/4 inch (6.35mm) phone jack to XLR/M For connecting balanced devices with 1/4 inch (6.35mm) phone and maybe used interchangeably. TRS (unbalanced) 1/4 inch (6.35mm) phone jack to XLR/M For connections of instruments with unbalanced outputs to balanced XLR inputs. TS (unbalanced) 1/4 inch phone (6.
CONTACT INFORMATION Mailing Address: JBL Professional 8500 Balboa Blvd. Northridge, CA 91329 Shipping Address: JBL Professional 8500 Balboa Blvd., Dock 15 Northridge, CA 91329 (Do not return product to this address without first obtaining prior authorization from JBL) Customer Service: Monday through Friday 8:00am -5:00pm Pacific Coast Time in the U.S.A. (800) 8JBLPRO (800.852.5776) www.jblproservice.com On The World Wide Web: www.jblpro.
WARRANTY INFORMATION The JBL Limited Warranty on professional loudspeaker products (except for enclosures) remains in effect for five years from the date of the first consumer purchase. JBL amplifiers are warranted for three years from the date of original purchase. Enclosures and all other JBL products are warranted for two years from the date of original purchase. Who Is Protected By This Warranty? Your JBL Warranty protects the original owner and all subsequent owners so long as: A.
EON 700 SERIES 11/21 8500 Balboa Boulevard Northridge, CA 91329 USA www.jblpro.
