P9 Beamspot Operating instructions Version 1.04 Software >= 1.0.
P9 - 02 -
P9 Content 1. Introduction ���������������������������������������������������������������������������������������������������������������������������05 1.1 P9 Beamspot models ������������������������������������������������������������������������������������������������������������������������05 2. Dimensions ���������������������������������������������������������������������������������������������������������������������������06 3.
P9 - 04 -
P9 1. Introduction 1.1 P9 Beamspot models The P9 beam spot is available in the light color HP (High Power). It can also be operated without any problems in the light colors 5800K (CRI> 90) and 3200K. Specification Color temperature Luminosity CRI HP - High Power with High CRI filter with CTO filter 6800 K 5800 K 3200 K 25.000 lm (15.000 lm output) 10.000 lm output 7.
P9 2. Dimensions 223,6 140 140 140 140 140 223,6 140 223,6 412 199 199 223,6 140 140 397 397 397 199 223,6 412 412 Farbe: 398 398 Name SallersteigDatum 15, 89134 Blaustein kuehngruen Erstellt Tel.: 07304 / 9617-0 Allgemeintoleranzen Fax.: 07304 / 9617-99 ISO 2768-mName Datum kuehngruen Erstellt Material: Farbe: Farbe: Blechdicke: Sallersteig 15, 89134 Blaustein Blechdicke: Tel.: 07304 Blechdicke: / 9617-0 Abmessung: Fax.: 07304 / 9617-99 Art.-Nr.
P9 3. Product overview Bottom cover Top cover Arm cover Handles LCD display Function keys Farbe: Lichtanlagentechnik GmbH Sallersteig 15, 89134 Blaustein Oberfläche: Material: Tel.: 07304 / 9617-0 Fax.: 07304 / 9617-99 Blechdicke: Abmessung: Datum Erstellt Name Head kuehngruen Allgemeintoleranzen ISO 2768-m Art.-Nr.
P9 4. Safety instructions ! ATTENTION: For your own safety, please read these operating instructions carefully before first use. This spotlight has left our company in excellent condition. To maintain this condition and to ensure safe operation, it is absolutely essential to observe the following safety instructions and warnings which are described in this operating manual.
P9 ! ATTENTION: This fixture corresponds to protection class I. For this reason, this spotlight must be connected to a mains socket with earthing contact. Never connect this device to a dimmer pack. During first use, some smoke and odour may occur. This is normal and does not necessarily mean that the device is defective. The device becomes hot during operation.
P9 ! ATTENTION: The distance between the light emission and the surface to be illuminated must be at least 2.0 metres. The maximum ambient temperature of 45°C must not be exceeded. ! ATTENTION: The front lens must be replaced if it is visibly damaged to the extent that its function is impaired, e.g. by cracks or deep scratches! Do not operate the device until you have become familiar with its functions. Prevent operation by persons who are not qualified to use the device.
P9 Connection outside Europe: The P9 Beamspot may only be operated on the following power supply systems: Mains P9 2 wires, 1 phase L N L N PE 3 wires, 1 phase L N L L L1 L2 L3 N L N 4 wires, 3 phases ! ATTENTION: In Canada, the P9 Beamspot may only be operated in a 2-wire, 1 phase network with a maximum voltage of 120V! N PE 5.3 Mains connection Connected loads: Voltage 100-240 V, frequency 50 - 60 Hz, power max.
P9 5.5 Signal connections 5.5.1 DMX cabling The DMX cabling (signal lines) should be done with a 4-pin cable with shielding. We recommend a DMX cable (110 Ohm, 2x0.22mm2 or 4x0.22mm2). The plugs and sockets are 5-pin XLR connectors, which can be purchased in specialist shops. Pin assignment: Pin1 = Ground/Shielding Pin2 = DMX Pin3 = DMX + Pin4 = not connected Pin5 = not connected 2 1 Cable with shielding 1 2 3 3 4 5 5 4 The P9 Beamspot has a DMX-in and DMX-out connector.
P9 5.6 Mounting the devices ! ATTENTION: Allow a fixture distance of at least 0.5 metres from easily flammable material and the distance between the light emission and the surface to be illuminated must be at least 2.0 meters. The P9 Beamspot can be placed on the floor or hang on a trussing system. Also a mounting horizontally to a truss system like in the picture is only allowed if the omega brackets are attached to the outer camlocks. (distance 223.
P9 6. Control panel The P9 Beamspot has a graphic colour touch display that can be rotated 180° when installed in a suspended position. The display can be rotated in the PERSONALITY MENU or via shortcut ENTER + UP in the main screen. All parameters of the P9 Beamspot can be set on the control panel (see menu overview page 16).
P9 Display illumination as function display The display illumination remains switched off during the reset. Slowly flashing display illumination when "JB-Lighting" is displayed means no DMX signal is present. A very rapidly flashing display illumination when "JB-Lighting" is displayed means that a new error has been stored in the "ERROR LIST", also an error message in the display (e.g. *PAN TIMEOUT) indicates this current error. This error occurs during this reset or in the operation before.
P9 6.1 Menu overview P9 Beamspot grey - corresponds to the default setting ENTER FACTORY DEF.
P9 SERVICE RESET FIXTURE ERROR LIST STANDALONE SURE? LIST PAN TIMEOUT CLEAR SURE? FUNCTION TEST START TEST DMX TEST DMX CHANNEL INIT PAN/TILT SURE? DISPLAY CONTR. D. CONTR: +000 +/- FINE ADJUST OFS PAN +/- OFS PAN +/OFS TILT +/- OFS FOCUS OFS FOCUS +/- SURE? EDIT STEP NR.
P9 INFO SOFTWARE VER. FIXTURE ID TOT OP. TIME TOT LAMP TIME TOT BAT CHARGE T. TEMP BASE LCD ACTUAL TEMP BASE PS ACTUAL TEMP HEAD MAIN ACTUAL TEMP HEAD DRV ACTUAL TEMP HEAD LED ACTUAL TEMP HEAD AMB. ACTUAL MAX MAX MAX MAX MAX MAX RESET? RESET? RESET? RESET? RESET? RESET? 6.2 FACTORY DEFAULTS - Factory settings To reset P9 Beamspot to the factory settings, go to the menu item FACTORY DEFAULTS, LOAD DEFAULTS.
P9 Under IP ADDRESS -> DEFAULT IP this can be changed from the network 10.xxx.xxx.xxx to a network 2.xxx.xxx.xxx. For your own self-definable IP address, you can set your own desired IP address under IP ADDRESS -> USER-IP. This address is divided into BYTE1 to BYTE 4 and can be set one after the other. DMX MODE - setting the operation mode The P9 Beamspot has 2 operating modes (see channel assignment for P9 Beamspot on page 24). All parameters of P9 Beamspot can be operated via mode 1.
P9 There is no danger to the life of the device in any mode, as the P9 Beamspot has a temperature safety shutdown. In addition, the LED module is switched off from an ambient temperature of 60°C! PAN TILT SPEED - setting pan/tilt speed In the PAN TILT SPEED menu you can set the maximum speed, the acceleration and thus also the movement volume of the P9 Beamspot. The following setting options are available. WHISPER: The speed of Pan / Tilt is reduced so much that a volume of 29dB (A) is not exceeded.
P9 LED FADE OUT - type of dimming Used to set how to dim the lower range from 0-5%. STANDARD: When dimming the headlamp, all LED's dim out at the same time. SOFT: When the headlamp is dimmed, the LED's are dimmed out in groups (in a row) one row after the other. 6.6 STANDALONE operation In standalone operation, up to 20 program steps can be stored in the P9 Beamspot, which can then run in an endless loop. The images can be saved in two ways.
P9 Operation via master-slave function: Connect the P9 Beamspot via DMX lines and activate the REMOTE menu item for all slave devices. To do this, navigate in the STANDALONE menu to the REMOTE sub-menu. Activate the REMOTE function by pressing and holding “ENTER”, and also pressing “ESC”. The spotlight is in slave mode when the display shows the status REMOTE INACTIVE or REMOTE ACTIVE. REMOTE INACTIVE: The P9 Beamspot is in slave mode but does not receive a DMX signal.
P9 7. Control options 7.1 DMX 7.1.1 Operating modes P9 Beamspot The P9 Beamspot has 2 different DMX modes. The respective mode can be set in the PERSONALITY, DMX MODE menu item. The set mode is displayed in the main menu.
P9 7.1.2 DMX channel functions P9 Beamspot M1 M2 1 1 M3 Function Pan (X) movement 546,74° 000-255 DMX 2 2 Pan (X) fine (16 Bit) 000-255 3 3 Tilt (Y) movement 281,16° 000-255 4 4 Tilt (Y) fine (16 Bit) 000-255 5 5 Control channel To enable uniform dimming manually via faders for all light mixing consoles, 5 different settings for the DMX smoothing are available.
P9 Setting for maximum DMX smoothing Dimmer fade out via fader (fast - slow) 128-135 DIMMER CURVE - selection of dimmer curve LINEAR - linear dimmer curve SQUARE - exponential dimmer curve SQUARE INVERSE - exponential inverse dimmer curve not used 136-136 137-137 138-138 139-139 RGB/CMY CURVE - selection of RGB/CMY curve SQUARE INVERSE OLD - Exponential inverse old RGB/CMY curve LINEAR - linear RGB/CMY curve SQUARE INVERSE - Exponential inverse RGB/CMY curve 140-140 141-141 142-142 FROST CURVE - selec
P9 6 7 8 9 10 Shutter Shutter closed Shutter open Open pulsing shutter >20Hz (rapid - slow) Shutter open Fade effect with dimmer (slow - rapid) Shutter open Shutter closed Open pulsing shutter <20Hz (rapid - slow) Shutter open Close pulsing shutter >20Hz (rapid - slow) Shutter closed Shutter fade, 0% (rapid - slow) Shutter open Shutter fade, 100% (rapid - slow) Shutter closed Random shutter 100% (rapid - slow) Shutter open Random shutter 0% (rapid - slow) Shutter closed Random shutter fade, 0% (rapid-
P9 13 15 17 20 Gobo 2 016-023 Gobo 3 024-031 Gobo 4 032-039 Gobo 5 040-047 Gobo 6 048-055 Gobo 7 056-063 Gobo 8 064-071 Gobo 9 072-079 Gobo 10 080-087 Gobo 11 088-191 Gobo wheel rotation (fast - slow) Gobo wheel rotation (fast - slow) 192-223 224-255 Gobo wheel 2 - rotating gobos Gobo 0 000-007 Gobo 1 008-015 Gobo 2 016-023 Gobo 3 024-031 - 27 -
P9 16 19 20 - 28 - Gobo 4 032-039 Gobo 5 040-047 Gobo 6 048-055 Gobo 7 056-191 Gobo wheel rotation (fast - slow) Gobo wheel rotation (fast - slow) 192-223 224-255 Gobo positioning/rotation 2 Gobo positioning 0° - 540° Gobo rotation, right (rapid - slow) Stop gobo rotation Gobo rotation, left (slow - rapid) 000-191 192-222 223-224 225-255 22 Gobo positioning/rotation 2 fine (16 Bit) 000-255 25 Color wheel White (color shift gobo on) White (color shift gobo off) White / CTB CTB CTB / Red
P9 21 22 23 24 25 26 27 30 32 33 34 35 28 Magenta (8 Bit) 0-100% 000-255 29 Fine magenta (16 Bit) 000-255 30 Yellow (8 Bit) 0-100% 000-255 31 Fine yellow (16 Bit) 000-255 32 CTO (8 Bit) 0-100% model HP, HC / CTB (8 Bit) 0-100% model WW 000-255 33 CTO fine (16 Bit) / CTB fine (16 Bit) model WW 000-255 34 Sparkle - Glitter effect Sparkle effect inactive Sparkle effect intensity (minimum - maximum) 000-000 001-255 Sparkle speed Faded sparkle effect (slow -> rapid) Switched spar
P9 7.1.3 Control channel Via the control channel different functions of the fixture can be switched. The following functions can be switched via the control channel.
P9 7.3 Streaming ACN The headlight can be controlled via sACN - Streaming ACN. To do this, set the sACN address via the menu item DMX / NET ADDR -> SACN ADDRESS and also select it via the menu item PERSONALITY -> DMX INPUT CONFIG -> NETWORK -> MODE -> SACN. In addition, define the IP address of the spotlight via PERSONALITY -> DMX INPUT CONFIG -> NETWORK -> IP ADDRESS. Further details and setting options can be found on page 18 7.
P9 7.5.
P9 Pan Tilt Speed ✔ ✔ Effect Speed ✔ ✔ Backlight Mode ✔ ✔ Disp Orientation ✔ ✔ Main Screen Mode ✔ ✔ Safe Mode Switch ✔ ✔ LED Fade Out Mode ✔ ✔ GET SET Temp Sens Base LCD ✔ ✔ Temp Sens Base PS ✔ ✔ Temp Sens Head PCB ✔ ✔ Temp Sens Head Drv ✔ ✔ 7.5.5 RDM sensor IDs RDM sensor ID DISCOVERY Note RDM sensors Temp Sens Head LED ✔ ✔ Temp Sens Head Air ✔ ✔ 8. Service 8.
P9 FINE ADJUST The FINE ADJUST area is protected by a key combination. Focus, shapers, shaper rotation, pan and tilt are calibrated at the factory. If there are large deviations in the calibration between the individual headlights, this can be corrected in the FINE ADJUST menu. For more information please contact our service. IDENTIFY DEVICE The RDM command IDENTIFY DEVICE can be called up or deactivated via this menu item. 8.
P9 Usable diameter, rotating gobowheel 1: 16.00 mm Usable diameter, rotating gobowheel 2: 16.00mm Outer diameter: 19.90 mm (+0/-0.1 mm) Maximum thickness: 1.1 mm 16/16mm 19.9 mm 8.3 Gobo size If you want to have your own gobos produced, please note the following dimensions: 8.4 Software update The P9 Beamspot can be updated via a USB stick with micro-USB connection. To do this, copy the file directly into the root directory of the USB stick.
P9 8.6 Cleaning the device ! WARNING: Disconnect fixture before opening! You should check the function of the fans in the head and foot at regular intervals. Above all, make sure that the air intakes and the interior of the P9 Beamspot are free of fluff and dust. To do this, open the head cover (4x camlocks with half a turn) and the base plate on the foot. You can clean the P9 Beamspot with a brush and a vacuum cleaner.
P9 9.
P9 TSENS BPS ER Sensor Error Base Power Supply AC/DC TSENS BLCD ER Sensor Error Base LCD TSENS BAIR ER Sensor Erroe Base Air TSENS HMAIN ER Sensor Error Head Main PCB TSENS HDRV ER Sensor Error Head LED Driver PCB TSENS HLED ER Sensor Error Head LED TSENS HAIR ER Sensor Error Head Air (Ambient) HIGH TEMP BLCD High Temperature Base LCD PCB HIGH TEMP BAIR High Temperatur Base Air (SPARX ONLY) HIGH TEMP BPS High Temperature Base PSU AC/DC HIGH TEMP HMAIN High Temperature Head Main PCB HIG
P9 10. Specifications Dimensions and weight Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 mm Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398 mm Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609 mm Net weight. . . . . . . . . . . . . . .
P9 11.
P9 - 41 -
P9 - 42 -
P9 - 43 -
JB-Lighting Lichtanlagentechnik GmbH Sallersteig 15 89134 Blaustein Tel. +49 7304 9617-0 Fax. +49 7304 9617-99 info@jb-lighting.de www.jb-lighting.
