HULALA H O M E ITEM NO.SCSD0748 NOTE: This brochure contains IMPORTANT safty info. Please read and keep for future reference.
A F F G E H G I D C B J K J OVERVIEW 2/22
MAINTAINANCE AND WARNING Keep furniture away from heat sources. Do not clean furniture with harsh cleaner or polishes. Do not use detergents, Solvents, abrasives, spray packs or leather cleaner. Usenon-color mild soap with warm water to clean spills(Mix 1:10 soap to water) Do not place furniture under direct sunlight, material will possibly fade over time. Do not use on site dry Cleaning machine. Children should not climb or jump on the furniture.
PARTS LIST 1 A B 1 PC E 1 PC F 1 PC I 1 PC 2 PCS 1 PC H G J 1 PC D C 2 PCS 1 PC K 2 PCS 1 PC Persons Required For Assembly： 2Personen 4/22
PARTS LIST 2 ⑨ x12 ⑩ x6 ⑪ x2 ⑭ x2 Ø20 ⑮ x4 ⑯ x1 M4 ⑫ x4 ⑰ x4 ⑬ x1 ⑱ x8 Ø8*30mm Be sure to inspect all packing material carefully for small parts, that may have come loose inside the carton during shipment.
HARDWARE LIST ① x46 ② x6 M3.5*14 ⑥ x4 M7*50 ⑦ x7 M4*35 M6*50 ③ x6 Ø6*35mm ⑧ x2 ④ x12 Ø8*30mm ⑤ x6 Ø15*11mm M6*40 SPARE ① x1 M3.5*14 ⑧ x1 ② x1 M7*50 ③ x1 Ø6*35mm ⑥ x1 M4*35 ⑦ x1 M6*50 M6*40 Be sure to inspect all packing material carefully for small parts, that may have come loose inside the carton during shipment.
When installing hinge, please pay attention to distinguish the category of hinge. ⑬ ⑭x2 ①x2 ① ⑭ ① I ⑭ H ① x2 ⑬ x1 ⑭ x2 M3.5*14 STEP1: picture shows.Use bolt ① to attach gasket ⑭ to door H&I，tighten bolts with screwdriver⑬.
When installing hinge, please pay attention to distinguish the category of hinge. ⑬ ⑮x4 ① ①X8 ⑮ ① I ⑮ ① H ① ⑮ x4 ① x8 ⑬ x1 ⑮ ⑮ M3.5*14 STEP2: Use screw ① to attach the hinges ⑮ to door panel (H)&(I)，tighten screws with screwdriver ⑬.
⑬ ③x6 ③ ④x6 ④ ④ ③ ③ ④ ④ ③ ③ ④ A ④ ③ ③ x6 ④ x6 ⑬ x1 Ø6*35mmØ8*30mm STEP3: Prepare for part A. Align the holes in part A, insert wooden dowel ④ by hand, tighten with screwdriver ⑬ and tighten ③.
⑭ ⑬ ①x4 A ⑭x2 The rear protrusion of the rebound member should face in the direction of the back panel. ① ① A ⑭ ⑭ x2 ① x4 ⑬ x1 M3.5*14 STEP4: picture shows.Use bolt ① to attach rebound device ⑭ to top panel，tighten bolts with screwdriver ⑬.
C＆E＆D C＆E＆D C＆E＆D ⑤x6 A C＆E＆D ⑬ ⑩x6 A A A D E ⑤ ⑤ C ⑤ ⑤ ⑤ ⑤ A ⑩ x6 Ø20 ⑤ x6 Ø15*11mm ⑬ x1 STEP5: Connect the part A with part (C,D,E). align the hole in the part (C,D,E),insert the bolt ③ and wooden dowel ④ in part A into part(C,D,E), and tighten the nuts⑤ with a screwdriver⑬.cover ⑩ the screw hole afte installation is finished. Make sure the groove is 11/22 in same side as picture show.
F F D E C A STEP6: slide in the part (F) into the groove in part C,E and E,D. make sure they are also in groove in part A.
⑯ ② ② ②x6 ② B ② ② ④ D ② ④ E ④ F C F ⑯ x1 M4 ④ x6 Ø8*30mm ② x6 M7*50 STEP7: Connect the part B the pre-assembled unit in step 6. Insert the wooden dowel ④ into the part (C,E,D) as the picture show. Then align the holes in part B,Insert screw ② and push it down so that it connects to parts (C,E,D). Next,and tighten the screw ② with an Allen key ⑯.
K J ⑧x2 ⑧ ⑯ J K ⑧ J ⑧ x2 M6*40 ⑯ x1 M4 STEP8: Prepare the leg racks. Align the holes of the J part with the holes of the K part, install the screw ⑧, and tighten the screw ⑧ with the allen key ⑯.
⑦ ⑯ ⑦ ⑦x7 J ⑦ J K B F C ⑦ x7 M6*50 ⑯ F x1 M4 STEP9: connect the leg frame to the cabinet. Attach the leg frame to the pre-assembled unit in step 7 with a screw ⑦ and tighten with a allen key⑯.
Attention: After installation, adjust theadjustable leveler to keep the cabinet balanced . Be sure to check all packing material carefully for small parts, which may have come loose inside the carton during shipment.
⑱x8 Shelf holder can be adjusted up or down A ⑱ ⑱ D E G C G B ⑱ x8 STEP11: Insert shelf pin⑱ into pre-assembled unit at step 10.attach adjustable shelf (G) to pin ⑱.
A F F D ⑬ ①x12 ⑨x12 ⑨ x12 ① x12 ⑬ x1 M3.5*14 STEP12: Attach part ⑨ to parts F,F with bolt ① and tighten the bolt with screwdriver ⑬.
A C&D A ⑬ H&I ①x16 C&D A E D G C B H STEP13: I ① x16 ⑬ x1 M3.5*14 Use screw ① to attach left door (H) and right door (I) to pre-assemble unit at step 12 ,tighten screw with screwdriver ⑬ .
Concealed hinges are three-way adjustable: or Sid Do ep an els or Do Sid ep an els Horizontal by screw adjustment! Concealed hinges are three-way adjustable: or Sid Do ep an els or Do Sid ep an els In-and-out by loosening the hinge arm mounting screw or via cam adjustment! Concealed hinges are three-way adjustable: or Do Sid ep an els or Do Sid Vertical via slots in the mounting plate or via cam adjustment! ep an els Hinge adjustment method 20/22
⑪X2 ⑫X2 ①X4 ⑫ ⑫ WA L C&D ⑬ L C&D WA LL D ⑰X4 F F WA LL ⑫X2 WALL ⑬ ⑥X4 ① x4 M3.5*14 ⑫ x4 ⑰ x4 ⑪ x2 Ø8*30mm STEP14: ⑥ x4 ⑬ x1 M4*35 Attach part ⑫ to parts D, C with bolt ① and tighten the bolt with screwdriver ⑬. Mark the position on the wall, that corresponds to the location of part ⑫ on the side panel D,C; Drill and insert the expandable screw ⑰ by hammer. Assemble the part ⑫ to the wall.
WARRANTY We strive to offer high-quality products, and we also try our best to satisfy each and every customer that orders from us with product or service as needed. We provide 30 days warranty starting from the time you receive the item. Each customer must provide a record of their order such as the order number, or item receipt for any items that are out of the warranty period you may also still receive replacement parts by purchasing them with our company if they are available.
