HULALA H O M E ITEM NO.SDSB0747 NOTE: This brochure contains IMPORTANT safty info. Please read and keep for future reference.
MAINTAINANCE AND WARNING 1.Keep furniture away from heat sources. 2.Do not clean furniture with harsh cleaner or polishes.Do not use detergents,solvents,abrasives,spray packs or leather cleaner. Use non-color mild soa with warm water to clean spills(Mix 1:10 soap to water). 3.Do not place furniture under direct sunlight,material will possibly fade over time. 4.Do not use on site dry cleaning machine.Children should not climb or jump on the furniture. 5.
EXPLOSIVE VIEW A H D I E G J F G L K J H E L I K C M N B O M 2PERSONEN OVERVIEW 03/26
PARTS LIST A x1 B x1 C x1 D x1 E x2 F x1 G x2 H x2 I x2 J x2 K x2 L x2 M x2 N x1 O x1 04/26
HARDWARE LIST #1 x88 M3.5*14 x8 #7 M6*50 #13 x4 #2 x10 M7*50 #8 x2 #3 x10 Ø6*35mm #9 x16 #4 x20 Ø8*30mm x24 #10 x4 x10 Ø15*11mm #11 x4 #6 x4 M4*35 #12 x2 8*30mm M6*40 #16 #5 #17 x4 x10 #18 #19 x4 #8 x1 Ø20 TOOL LIST #14 x1 #15 x1 M4 HARDWARE SPARE LIST #1 x1 M3.
ASSEMBLY INSTRUCTIONS STEP-1 1.Prepare for part A. Align the holes in part A, insert wooden dowel #3 .
ASSEMBLY INSTRUCTIONS STEP-2 1.Prepare for part A. Align the holes in part A, insert bolt #4 , and tighten bolt #4 with screwdriver #15.
ASSEMBLY INSTRUCTIONS STEP-3 1.picture shows.Use bolt #1 to attach rebound parts #16 to panel，tighten bolts with screwdriver #15. #15 #1 #16 A The rear protrusion of the rebound member should face in the direction of the back panel. #16 x4 #1 x8 #15 x1 M3.
ASSEMBLY INSTRUCTIONS STEP-4 1.Connect the part A with part (C,D,E,E,F). align the hole in the part (C,D,E,E,F),insert the bolt #3 and wooden dowel #4 in part A into part(C,D,E,F).and tighten the nuts#5 with a screwdriver#15.cover #18 the screw hole afte installation is finished. Make sure the groove is in same side as picture show.
ASSEMBLY INSTRUCTIONS STEP-5 1.slide in the part (H,G,G,H) into the groove in part C,E and E,F and F,E and E,D. make sure they are also in groove in part A.
ASSEMBLY INSTRUCTIONS STEP-7 1.Connect the part B the pre-assembled unit in step 6. Then align the holes in part B,Insert screw #2 Insert the wooden pin #4 into (C,D,E,F), by hand.and push it down so that it connects to parts C,D,E,F,E. Next,and tighten the screw #2 with an Allen key#14.
ASSEMBLY INSTRUCTIONS STEP-8 1.Prepare the leg racks. Align the holes of the M part with the holes of the N part, install the screw #8, and tighten the screw #8 with the allen key #14.
ASSEMBLY INSTRUCTIONS STEP-9 1.connect the leg frame to the cabinet.Attach the leg frame to the pre-assembled unit in step 7 with a screw #7 and tighten with a allen key#14.
ASSEMBLY INSTRUCTIONS STEP-10 1.connect the middle leg to the cabinet.Attach the middle leg to the pre-assembled unit in step 9 and hand tighten.
ASSEMBLY INSTRUCTIONS STEP-11 1.Insert shelf pin#9 into reassemble unit at step 10.
ASSEMBLY INSTRUCTIONS STEP-12 1. Use screw #1 to attach the gasket #16 to door panel (L)&(K） tighten screws with screwdriver #15. #1x2 #16x2 K&L #15 L K L #1x2 K K&L #16x2 #15 #15 x1 #16 x4 #1 x4 M3.
ASSEMBLY INSTRUCTIONS STEP-13 1.Use screw #1 to attach the hinges #19 to door panel (K)&(L)，tighten screws with screwdriver #15. #1x8 #19x4 #15 #19 When installing hinge, please pay attention to distinguish the category of hinge #1 #19 #1 L K #19 #1 #19 #1 #15 x1 #1 x8 #19 x4 M3.
ASSEMBLY INSTRUCTIONS STEP-14 1.Use screw #1 to attach left (K) and right door (L) to reassemble unit at step 11 ,tighten screw with screwdriver #15 . #1x16 K&N #15 C&D C&D K&N D L C K #15 x1 #1 x16 M3.
ASSEMBLY INSTRUCTIONS STEP-15 1. Use screw #1 to attach the hinges#17 to door panel (L)&(K)tighten screws with screwdriver #15. #1x8 K #17 #1 #17 #1 #17 #1 #17x4 #15 L #17 #1 When installing hinge, please pay attention to distinguish the category of hinge #17 x4 #15 x1 #1 x8 M3.
ASSEMBLY INSTRUCTIONS STEP-16 1.Use screw #1 to attach middle door (K) to reassemble unit at step 14 ,tighten screw with screwdriver #15 . F #1x8 K K F #15 K F K L D #15 x1 #1 x8 M3.
ASSEMBLY INSTRUCTIONS STEP-17 1.Use screw #1 to attach middle door(L) to reassemble unit at step 16 ,tighten screw with screwdriver #15 . L F #15 #1x8 F L L K F L C K #15 x1 #1 x8 M3.
ASSEMBLY INSTRUCTIONS Concealed hinges are three-way adjustable: or Sid Do ep an els or Do Sid ep an els Horizontal by screw adjustment! Concealed hinges are three-way adjustable: or Sid Do ep an els or Do Sid ep an In-and-out by loosening the hinge arm mounting screw or via cam adjustment! els Concealed hinges are three-way adjustable: or Do Sid ep an els or Do Sid Vertical via slots in the mounting plate or via cam adjustment! ep an els Hinge adjustment method 22/2
ASSEMBLY INSTRUCTIONS STEP-18 . Attention: After installation, adjust the adjustable leveler to keep the cabinet balanced .
ASSEMBLY INSTRUCTIONS STEP-19 1.Attach part #10 to parts G,H,H,G with bolt #1 and tighten the bolt with screwdriver #15. G H H D #1 #10 G G&H G&H #15 #10 #10x24 #1x24 #10 x24 #15 x1 #1 x24 M3.
ASSEMBLY INSTRUCTIONS #1 x4 M3.5*14 #13 x4 #11 x4 #12 x2 x4 #6 #15 x1 M4*35 8*30mm STEP-20 1.Attach part #13 to parts D, C with bolt #1 and tighten the bolt with screwdriver #15.Mark the position on the wall, that corresponds to the location of part #13 on the side panel D,C; Drill and insert the expandable screw #11 by hammer.Assemble the part #13 to the wall. Align the hole in the part #13 with the expandable screw #11, use screw #6 to attach it and tighten by screwdriver #15.
WARRANTY 1.We strive to offer high-quality products,and we also try our best to satisfy each and every customer that orders from us with product or service as needed. 2.We provide 30 days warranty starting from the time you receive the item.Each customer must provide a record of their order such as the order number,or item receipt for any items that are out of the warranty period you may also still receive. 3.Replacement parts by purchasing them with our company if they are available.
