HULALA H O M E ITEM NO.SBHM0736 NOTE: This brochure contains IMPORTANT safty info. Please read and keep for future reference.
MAINTAINANCE AND WARNING Keep furniture away from heat sources. Do not clean furniture with harsh cleaner or polishes. Do not use detergents, Solvents, abrasives, spray packs or leather cleaner. Usenon-color mild soap with warm water to clean spills(Mix 1:10 soap to water) Do not place furniture under direct sunlight, material will possibly fade over time. Do not use on site dry Cleaning machine. Children should not climb or jump on the furniture.
A J C D H I E F I H G M N L K Q B O Q OVERVIEW P
HARDWARE LIST A B 1 PC E 1 PC F 1 PC I J M 1 PC 2 PCS L 1 PC 1 PC 1 PC P O 1 PC 1 PC H K N 1 PC 1 PC G 1 PC 2 PCS D C 1 PCS 1 PCS Q 2 PCS Persons Required For Assembly：2Personen
PARTS LIST 1 ① x52 ④ x27 ④ x1 SPARE ① x1 Be sure to inspect all packing material carefully for small parts, that may have come loose inside the carton during shipment.
PARTS LIST 2 ② x8 ③ x10 ⑤ x16 ⑥ x4 ⑦ x4 ⑧ x1 ⑨ x1 ⑩ x4 ⑪ x2 ⑫ x4 ⑬ x4 ⑭ x1 ⑮ x18 ⑯ x18 Be sure to inspect all packing material carefully for small parts, that may have come loose inside the carton during shipment.
ASSEMBLY INSTRUCTIONS ⑧ x1 C&D&E& F&G C&D&E& F&G ⑧ B B G F E D C B STEP1: Insert left side panel (C)、middle vertical panel D&E&F and right side panel (G) into the corresponding hole of bottom panel (B) as image，then tighten it with allen key ⑧
⑧ x1 A ⑧ A C&D&E&F&G C&D&E&F&G A G F E D C STEP2: Attach top panel (A) to preassemble unit at step 1 as image，and tighten it with allen key ⑧
④ x27 ⑨ x1 ⑨ ④x27 C J B G STEP3: Attach back panel (J) to preassemble unit at step 2 with screw ④，and tighten it with screwdriver ⑨.
⑧ x1 ② x4 ⑮ x4 ⑯ x4 Do not fully tighten bolts until all bolts are in position!!! ⑯ ⑮ Q ② ⑯ Q ⑧ ⑮ ② O STEP4: Insert part (Q) into part (O) as picture show，then use flat washer ⑯ 、spring washer ⑮ and bolt ② to attach part (Q) to part (O), make sure all holes aligned and tighten all bolts with allen key ⑧.
⑧ x1 ② x4 ⑮ x4 ⑯ x4 1: Q P ⑯ Q ⑮ O ② ⑧ Q 2: ⑯ ⑮ Q P O ② Do not fully tighten bolts until all bolts are in position!!! STEP5: Insert part (P) into part (Q)，use plat washer ⑯、spring washer ⑮ and bolt ② to attach part (Q) to part (P),make sure all holes aligned and tighten all bolts with allen key ⑧.
⑧ x1 ③ x10 ⑮ x10 ⑯ x10 ③x10 Do not fully tighten bolts until all bolts are in position!!! ⑧ O ⑮x10 ⑯x10 Q P Q B STEP6: Use plat washer⑯、spring washer⑮ and bolt ③ to attach the preassemble unit at step 5 to panel (B),make sure all holes aligned and tighten all bolts with allen key ⑧.
⑤ x16 Shelf holder can be adjusted up or down ⑤x16 G F H E I D I C H STEP7: Insert shelf pin ⑤ into preassemble unit at step 6，and attach adjustable shelf H&I to it.
① x16 ⑨ x1 ⑦ x4 ⑥ x4 ⑭ x1 ⑥ ⑭ N ⑦ ⑭ M ⑭ When installing hinge，please pay attention to distinguish the category of hinge L ⑥ K ⑦ ⑭ ⑨ ① ⑥ STEP8: ⑨ ① Use screw① to attach the hinges ⑥ to door panel N&K，tighten screws with screwdriver⑨. Use screw① to attach the hinges ⑦ to door panel M&L，tighten screws with screwdriver⑨. Stick parts ⑭ on panel N&M&L&K as image.
① x16 ⑨ x1 ① ⑥ ⑨ G N C K STEP9: Use screw ① to attach left door (K) and right door (N) to preassemble unit at step 8 ， tighten screw with screwdriver ⑨.
① x8 ⑨ x1 ⑨ ① ⑦ E L STEP10: Use screw ① to attach left middle door (L) to preassemble unit at step 9 ,tighten screw with screwdriver ⑨ .
① x8 ⑨ x1 ⑦ ① ⑨ M E STEP11: Use screw ① to attach right middle door (M) to preassemble unit at step 10 ,tighten screw with screwdriver ⑨ .
Concealed hinges are three-way adjustable: or Do Sid ep an els Do or Sid ep an els Horizontal by screw adjustment! Concealed hinges are three-way adjustable: or Sid Do ep an els or Do Sid ep an In-and-out by loosening the hinge arm mounting screw or via cam adjustment! els Concealed hinges are three-way adjustable: or Do Sid ep an els or Do Sid Vertical via slots in the mounting plate or via cam adjustment! Hinge adjustment method ep an els
STEP12: Attention:After installation, adjust the adjustable leveler to keep the cabinet balanced .
1: WA LL 2: WA L 3: L ⑩ ⑨ ⑬ ⑫ ① LL ⑫ WA LL ⑪ ⑫ WA ⑨ A J ① x4 ⑫ x4 ⑩ x4 ⑪ x2 ⑬ x4 ⑨ x1 STEP13:Install the anti-collapse device. 1. Mark the position on the wall, that corresponds to the location of part⑫ on the back of panel J; Drill and insert the expandable screw ⑩ by hammer. 2. Assemble the part ⑫ to the wall. Align the hole in the part ⑫ with the expandable screw ⑩, screw⑬ in and tighten by screwdriver. 3.
WARRANTY We strive to offer high-quality products, and we also try our best to satisfy each and every customer that orders from us with product or service as needed. We provide 30 days warranty starting from the time you receive the item. Each customer must provide a record of their order such as the order number, or item receipt for any items that are out of the warranty period you may also still receive replacement parts by purchasing them with our company if they are available.
