2 PERSON EN ITEM NO. NSJY0539 i NOTE: This brochure contains IMPORTANT safety info. Please read and keep for future reference.
@ Keep furniture away from heat. @ Do not clean furniture with harsh cleansers or polish. Do not use detergents, Solvents, abrasives, spray packs or leather cleaner. Use non-color mild soap with warm water clean spills(Mix 1:10 soap to water) & Do not place furniture under direct sunlight, material will possibly fade over time. # Do not use on site dry Cleaning machine. # Children should not climb or jump on the furniture. # Do not write on furniture without a padded barrier to protect the surface.
Top Panel Bottom Panel Left Side Panel | Right Side Panel Fixed Shelf 1PC 1PC 1PC 1PC 1PC Cross Rail Back Panel Cross Rail Power Panel | Drawer Front Panel 1PC 1PC 1PC 1PC 2 PCS Drawer Left Panel 2 PCS Drawer Right Panel PCS Drawer Back Panel PCS Drawer Bottom Pane! PCS Leg 4 PCS 4/17
LIST 28*30mm Wood Dowel Cam Bolt Cam Lock Bolt Round Head Bolt 26 PCS 6 PCS 6 PCS PCS PCS 28*25mm @3*15mm*D6mm 26*15mm Knob Flat Head Screw Small Round Allen Wrench Flat Head Screw PCS 20 PCS Head Screw 1PC PCs #11 #12 Power Safety Strap Kit 1PC 18ET #3 #5 @28*30mm Wood Dowel Cam Bolt Cam Lock Bolt Round Head Bolt 1PC 1PC 1PC 1PC 1PC eng 28*25mm 23*15mm*D6mm 26*15mm Flat Head Screw San Round Flat Head Screw Head Screw 1PC 1PC 1PC the carton during shipment.
STRICT STEP 1: 1.Insert wooden dowel #1 into leg O 2. Then use Allen wrench #9 and bolt #4 to attach bottom panel B to leg O,make sure all holes aligned and tighten all bolts to secure.
STEP 2: 1.Insert wooden dowel #1& cam bolt #2 into the corresponding hole position of side panel C&D.
STEP 3: 1.Insert fixed shelf E and cross rail F into right side panel D as picture show . 2.Use cam lock #3 to attach fixed shelf E &cross rail F to right side panel D,then tighten it with Allen wrench #9. 3.Insert cross rail H into right side panel D as picture show.
STEP 4: 1.Insert the reassemble unit E&F&D&H into left side panel C as picture show. 2.Use cam lock #3 to attach reassemble unit E&F&D&H to left side panel C as picture show, then tighten it with Allen wrench #9.
Locked Unlocked 1.Insert wooden dowel #1 into the corresponding hole position of bottom panel B. 2.
STEP 6: 1.Put back panel G in the groove of reassemble step 5, then use Allen wrench #9 and screws #8 to attach it, make sure all holes aligned and tighten all screws to secure.
STEP 7: 1.Put power #11 in power panel |, use Allen wrench #9 and screws #10 to attach power #11 to power panel |, make sure all holes aligned and tighten all screws to secure. 2.Use Allen wrench #9 and screws #7 to attach the reassemble power panel | to the reassemble step 6, make sure all holes aligned and tighten all screws to secure.
STEP 8: 1.Insert wooden dowel #1 into the corresponding hole position of reassemble step 7 as picture show. 2.
STEP 9: 1.Use Allen wrench #9 and screws #7 to attach drawer right panel K and drawer left panel L to drawer back panel M; make sure all holes aligned and tighten all screws to secure. 2.Insert drawer bottom panel N into the rear slots of side drawer panels K & L. Ensure that all components are inserted. 3.Use Allen wrench #9 and screws #7 to attach drawer front panel J to side drawer panels K&L, make sure all holes aligned and tighten all screws to secure.
STEP 10: 1.Slide the female sliding rail of side panel C&D to the most front and keep it . 2.Insert the drawer male sliding rail into the female sliding rail as picture show. 3.Pull out the drawer completely, while pressing the plastic snap locks in the left and right side slides of the drawer, keep the snap locks depressed and pull the drawer to remove the drawer.
2843/4" 2811/2" Safety Strap Kit Anchor Washer Short Screw Long Screw Safety Wall Strap 1ST 1PC PCS 1PC 1PC 1PC SAFETY WALL STRAP INSTALLATION Note: It is highly recommended to install this safety strap kit to prevent tipping,damage and/or injury. 1.Insert short screw (C) through washer (B) and safety wall strap (E) and attach to top panel (part A) using fillips head screwdriver. 2.Drill a 11/32" hole where you want to secure the unit.
WARRANTY We strive to offer high-quality products, and we also try our best to satisfy each and every customer that orders from us with product or service as needed. We provide 30 days warranty starting from the time you receive the item. Each customer must provide a record of their order such as the order number, or item receipt for any items that are out of the warranty period you may also still receive replacement parts by purchasing them with our company if they are available.
