User's Manual

A. INSTALL THE BATTERY
1. Place the plastic tabs on the base of the battery in the notches at the bottom of the battery compartment.
2. Press the top of the battery to snap in place.
3. Push the battery lock switch to the lock position by sliding it to the left.
B. CHARGE THE BATTERY
Important Note: The main battery charges the backup battery in the XT Series unit. Once the main battery is
fully charged, do not remove it from the unit for 24 hours. During this period, the unit cannot maintain any
user data if the battery is removed.
To charge the battery using the USB AC Adapter Kit:
1. Slide adapter plug onto the AC adapter housing.
2. Insert the USB end of the USB cable into the USB port on the AC adapter housing.
3. Insert the micro USB end of the USB cable into the micro USB port on the XT Series unit.
4. Plug in the AC Adapter.
Use only easily accessible wall sockets that are easily reached with the length of supplied power cable.
To charge the battery using the USB Syncing/Charging Cable:
1. Connect the power supply to the cable accessory, then connect the line cord to the power supply.
2. Connect snap-on end of cable accessory to bottom of XT Series unit making sure the Janam logo on the
connector faces front.
3. Plug in the power supply.
Use only easily accessible wall sockets that are easily reached with the length of supplied power cable.
To charge the battery using a Cradle Kit:
1. Connect the power supply to the cradle, then connect the line cord to the power supply.
2. Plug in the power supply.
Use only easily accessible wall sockets that are easily reached with the length of supplied power cable.
3. Placethedeviceincradle.TheLEDonthedevicewillilluminatetoconrmconnection.
4. The battery is fully charged in approximately 2 hours.
Getting Started
Page 5
Getting Started (continued)
5. To charge a battery in the spare battery well, insert the battery into the well top down (connectors
on the battery should face downward and to the back of the cradle) and gently press down. The LED
lightonthecradlewillilluminatetoconrmconnection.
C. ATTACH THE HANDSTRAP
1. Insert plastic fastener on handstrap into the handstrap
retainer clip face down as shown in diagram. It will click
into place.
2. Extend other end of handstrap toward base of XT Series
unit (rough side of Velcro should be facing up). Feed
through the handstrap bar as shown in diagram.
3. Pull handstrap through handstrap bar and fasten Velcro to
close the strap. Fit strap and secure device to user’s hand
by adjusting Velcro as needed.
D. REMOVE THE BATTERY
1. Push the battery lock switch to the unlock position by sliding it to the right.
2. Liftthebatteryattheupperrightcorner(ngerliftgroovemarkedbyanarrow).
E. ACCESS SIM CARD SLOT AND MICRO SD CARD SLOT
1. After removing the battery, lift the media card compartment cover using notch at the top (it drops
down to open).
2. To access the SIM card slot, slide silver SIM card cover to the left and lift open.
3. To access the microSD card slot, slide silver microSD card cover to the left and lift open.
XT Series Quick Start GuidePage 6
Hardware Overview
Page 3
6
1
9
14
13
16
18
3
19
2
17
1. Power Button
2. Enter Key
3. Back Space Key
4. Micro USB Port
5. Phone Disconnect Key
6. Headset with Microphone
7. Volume Control
8. Right Trigger
9. LCD
10. NoticationLEDs
11. Indicator LED
12. Scan Window
13. Receiver
14. Left Trigger
15. Push-to-Talk Button
16. Scan Trigger
17. Phone Connect Key
18. Shift Key
19. Microphone
20. Yellow Function Key
21. Connector
22. Blue Function Key
(Numeric keypad only)
20
Numeric KeypadQWERTY Keypad
7
8
5
1
2
3
4
4
5
6
7
8
9
11
21
13
14
16
17
18
19
20
21
22
12 12
15
15
10
11
10
Hardware Overview
Janam Technologies LLCPage 4
8
5
2
4
67
9
10
1
Battery Compartment
1. Battery
2. Battery Lock Switch
3. Finger Lift Groove
4. Speaker
5. Handstrap Retainer Clip
6. Scan Window
7. Lanyard Connector
8. Stylus
9. Camera or IrDA Window
10. Stylus Slot
11. Handstrap Bar
12. Media Card Compartment Cover
13. microSD Card Cover/Slot
14. SIM Card Cover/Slot
11
13
14
12
3