Full Product Manual

116
General
Product
Information
Working
Safely
Tools for
Cutting and
Fastening
General
Installation
Requirements
General
Fastener
Requirements
Finishing and
Maintenance
HardieTrim®
Boards/Battens
HardieWrap®
Weather Barrier
HardieSoffit®
Panels
HardiePlank®
Lap Siding
HardieShingle®
Siding
HardiePanel®
Vertical Siding
ESR-1844 &
2290 Report
Appendix/
Glossary
ICC – IBC® & IRC®/2006 – ALLOWABLE FASTENER SPACING (IN.)
HardiePlank
®
Lap Siding fastened to ASTM C 90 Concrete Wall
Basic Wind Building <6½-inch wide 7¼- & 7½-inch wide 8- & 8¼-inch wide 9¼- & 9½-inch wide
Speed Height (feet)
Exposure Exposure Exposure Exposure
B C D B C D B C D B C D
100 mph 0-15 24 24 24 24 24 24 24 24 21 24 23 19
20 24 24 24 24 24 23 24 24 20 24 21 18
30 24 24 24 24 24 21 24 22 19 24 20 17
40 24 24 23 24 24 20 24 21 18 24 19 16
50 24 24 22 24 22 19 24 20 17 24 18 15
60 24 24 22 24 22 19 24 19 17 23 17 15
110 mph 0-15 24 24 22 24 24 19 24 21 17 23 19 15
20 24 24 21 24 22 18 24 20 16 23 18 15
30 24 24 20 24 20 17 24 18 15 23 16 14
40 24 22 19 24 19 16 23 17 15 21 15 13
50 24 21 18 24 18 16 22 16 14 20 14 12
60 24 20 18 23 18 15 21 16 14 19 14 12
120 mph 0-15 24 23 19 24 20 17 21 18 15 19 16 13
20 24 22 18 24 19 16 21 17 14 19 15 12
30 24 20 17 24 17 15 21 15 13 19 14 12
40 24 19 16 22 16 14 20 14 12 18 13 11
50 24 18 16 21 16 13 18 14 12 17 12 11
60 23 17 15 20 15 13 18 13 11 16 12 10
130 mph 0-15 24 20 16 21 17 14 18 15 12 16 14 11
20 24 19 15 21 16 13 18 14 12 16 13 11
30 24 17 14 21 15 12 18 13 11 16 12 10
40 22 16 14 19 14 12 17 12 11 15 11 9
50 21 15 13 18 13 11 16 12 10 14 11 9
60 20 15 13 17 13 11 15 11 10 13 10 9
140 mph 0-15 21 17 14 18 15 12 16 13 11 14 12 10
20 21 16 13 18 14 12 16 12 10 14 11 9
30 21 15 12 18 13 11 16 11 10 14 10 9
40 19 14 12 16 12 10 15 11 9 13 9 8
50 18 13 11 15 11 10 14 10 9 12 9 8
60 17 13 11 15 11 10 13 10 9 12 9 8
150 mph 0-15 18 15 12 16 13 11 14 11 9 12 10 8
20 18 14 12 16 12 10 14 11 9 12 10 8
30 18 13 11 16 11 9 14 10 8 12 9 7
40 16 12 10 14 10 9 13 9 8 11 8 7
50 15 12 10 13 10 9 12 9 8 11 8 7
60 15 11 10 13 10 8 11 8 7 10 8 7
Notes to Table:
1. Fasteners shall be ET&F Fastening Systems, Inc. ET&F block Nail (ET & F No. ASM-144-125, head dia. = 0.30 in., shank dia. = 0.14 in., length = 1.25-in. long) or
Max System block Nail (CP-C 832 W7-ICC, head dia. = 0.30 in., shank dia. = 0.15 in., length = 1.3 in.).
2. Maximum basic wind speed shall be 150 mph.
3. Interpolation to address building height and other plank widths is permitted.
4. The lap conceals the fasteners of the previous course (Blind Nailed).
5. 1 inch = 25.4 mm, 1 foot = 305 mm, 1 mph = 0.44 m/s
Additional Information (continued)