Installation Guide

English
Freestanding Baths
Installation Instructions www.jacuzzi.com Page 5
1
Install the metal drain/waste
tting (supplied with the tub)
into the drain hole as illustrated
(Fig 2). Ensure that the drain
opening on the waste tting is
situated in the integral overow
channel (Fig. 2).
2
Use clear silicone to adhere the
bottom gasket to the underside
of the integral overow channel.
3
Secure the waste tting with
the supplied waste tting nut.
Apply thread sealant to the
threads prior to inserting the
nut. Overtightening the nut
may cause shell damage.
Ensure the drain opening on the waste tting is not exposed after tightening of the nut.
4
Install a PVC thread adaptor (not supplied) to the metal waste tting. This is to provide a PVC to PVC drain adapter
connection protruding from the oor. Water test tting for leaks before installation. NOTE: Use PVC Cement per ASTM D2564
on all PVC joints.
Installation Instructions for Tubs with Integral Overow
TOE-TAP DRAIN COVER
(SUPPLIED)
INTEGRAL OVERFLOW
CHANNEL
DRAIN OPENING
WASTE FITTING
TOP GASKET (SUPPLIED)
WASTE FITTING NUT
(SUPPLIED)
WASTE FITTING
(SUPPLIED)
WASTE FITTING
BOTTOM GASKET
(SUPPLIED)
SILICONE ALL AROUND
1-1/2” FPT TO SLIP
ADAPTER (NOT
SUPPLIED)
INTEGRAL OVERFLOW
CHANNEL
DRAIN
DETAIL
SEE DRAIN DETAIL
Fig 1.
Fig. 2
Installation Instructions for 1-Piece Tub
1
Set the tub in its place and position precisely with respect to
the drain-overow location. Verify where the indentation for
the drain is in relation to the drain-overow. Use a marker to
outline the perimeter of the entire tub directly on the oor
(Fig. 3).
2
Mark a trough for the overow drain location on the oor.
The drain/overow extends below the bottom of the bath.
The drain/overow requires a cutout of the oor
for providing space to accommodate the extension. Do not
exceed the dimensions of the tub perimeter. When the
above locations have been marked on the oor, remove the
tub, set it aside and continue with the installation process.
3
Prepare the drain/overow trough according to the
dimensions shown in the Technical Specications section.
The depth of the trough depends on the vertical extension
of the drain elbow at the bottom of the plumbing below
the oor level. Install the drain/overow according to the
manufacturer’s instructions. Refer also to the Technical
Specications section.
Watertight installation of the drain is the installer’s
responsibility. Drain leakage is excluded from the Jacuzzi
Luxury Bath warranty of this product.
4
Before the tub may be secured to the oor, the following
steps must be completed: Place the tub on the oor in
relation to the drain/overow. Place the tub on the oor and
line up with the markings previously made on the oor.
Floor-mounted or wall-mounted faucetry can be used exterior
to the bath, this can be installed after the bath is installed into
the oor.
Clean up debris left over from the construction steps taken thus far. Also, remove the perimeter outline of the template on
5
the oor. Use silicone to attach tub to the sub oor. Make sure the tub is properly oriented according to the drain/overow
end.
A bead of silicone sealant should be applied around the bottom of the tub. Carefully place the tub on the oor in the correct
position and press to the oor. Place weights around the perimeter and allow the adhesive to cure before proceeding.
Silicone
Bottom
View
Side
View
Fig. 2
Units equipped
with Whisper+
Technology
TM
or Heated Soak
only. Refer to
supplied template
for electrical
connection location.
Fig. 3