INSTALLATION AND OPERATING INSTRUCTIONS Installer: Leave this manual for homeowner. Homeowner: Read this manual and keep for future reference.
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS CAUTION: TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE PERIODICALLY IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS. WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; CHILDREN SHOULD NOT USE HYDROMASSAGE BATHTUB WITHOUT ADULT SUPERVISION.
PRECAUTIONS • • • • • • • • • • • Do not operate the whirlpool system unless the bath is filled with water to at least 2" above the highest jet. Never drop or insert any object into any opening. Do not use oil-based bath additives in your whirlpool bath. When cleaning your bath, do not use abrasive substances which will damage the bath's surface. To prevent discoloration of the acrylic finish, do not fill the bath with water in excess of 140°F (60°C).
CONTENTS Specifications _________________________________________________________________________ 1-2 Roughing-in Reference _________________________________________________________________ 3-4 Installation ___________________________________________________________________________ 5-8 Framing and Support _________________________________________________________________ 5 Service Access _____________________________________________________________________ 6 Electrical Connections _________________________
SPECIFICATIONS Important: Read complete instructions before beginning installation. Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and fittings necessary for whirlpool operation. An optional drain/overflow kit is available for installation on the bath. Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the bath by the plumbing at any time; handle by the shell only.
SPECIFICATIONS CORNER BATHS 2" H 51 mm FRONT VIEW SIDE VIEW ESPREE 6060 A B DRAIN/OVERFLOW 1" H 25 mm FRONT VIEW SIDE VIEW ESPREE 6060 WITH SKIRT SPECIFICATIONS (Corner) DIMENSIONS MODEL DRAIN/OVERFLOW DIMENSIONS CUTOUT ESPREE 6060 60" 60" 22" (1524 mm) L (1524 mm) L ( 559 mm) H 18-1/2" (470 mm) A 12-1/4" (311 mm) B See Page 4 888 lb (404 k/g)/ 36 lb/sq. ft. (176 kg/sq.
ROUGH-IN Note: Unless otherwise specified, units are produced with left or right-hand versions.
ROUGH-IN 33-1/2" 60" 33-1/2" 60" 60" 21" X 4" 60" 21" X 4" 6-3/4" 6-3/4" 24 -3 50-1/8" " /8 " -3 /8 24 8" 3/ " 24 1/2 33 6" 4 12-1/2" 50-1/8" " /8 -3 " 4 2 /2 -1 " 33 46 12-1/2" Junction Box (Right hand shown. Left hand is a mirror image) (Right hand only as shown) ESPREE 6060 WITHOUT SKIRT ESPREE 6060 WITH INTEGRAL SKIRT Note: 1. The overall dimensions are nominal with a tolerance of +0 and -1/4". 1.
INSTALLATION Framing and Support The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout in the floor. The floor structure beneath the bath must be able to support a total weight of bath, water, and bather. Refer to the table under total weight for your model. The unit must be supported from the bottom of the bath and not from the bath rim or tile flange. If the subfloor is level, no other preparation is necessary. You can proceed to install the bath.
INSTALLATION Service Access with Integral Skirt Service Access Service access is through the removable skirt panels. For partially or fully sunken installations, allow for access to service connections. It is the installer's responsibility to provide sufficient service access. The recommended minimum dimensions allowable for service to the bath are shown in the "Service Access" illustration.
INSTALLATION Electrical Connections Electrical Connection 6060 With Heater A separate circuit, which must be protected by a Ground Fault Circuit Interrupter (GFCI), is required. Install a duplex outlet to the studwall underneath the bathtub, at least 4 inches above the floor. The duplex outlet is not provided. Because these units are manufactured with a safe, convenient Magic Touch whirlpool ON/OFF switch on the bath itself, no remote switch or timer is necessary.
INSTALLATION Drain Information Water Supply A drain/overflow assembly (sold separately) must be installed on the bath, water tested, and connected to the sanitary system of the house. After opening the carton, inspect for damage and verify that the kit is of the proper finish. In the Jacuzzi Whirlpool Bath drain/ overflow kit, note that the waste flange, strainer, overflow cover and cover screws are packaged in a separate package within the kit to protect the trim finish.
OPERATION All baths manufactured by Jacuzzi Whirlpool Bath are designed for "fill and drain," which means the bath should be drained after each use and filled with fresh water by the next bather. This is a health precaution, as these baths are not designed to hold water continuously like pools or spas. If you want a unit designed to continuously hold water, see your Jacuzzi Whirlpool Bath dealer for the complete line of whirlpool spas available.
OPERATION Water Force: The high volume, fully adjustable jets can be adjusted to control the force of the water coming into the bath. For robust action, increase the force of the flow by rotating the jet handles to the left (counterclockwise). For a more gentle effect, rotate the handles to the right (clockwise). Never run the whirlpool system with all the jets closed. Force of Air: Two knobs located on the bath serve as controls for the air induction system.
MAINTENANCE Cleaning the Bath Bath Additives To clean your bath, simply use a mild, nonabrasive liquid detergent solution. You can protect and restore the gloss to a dulled acrylic surface by applying Meguiar's #10 Mirror Glaze, a product specifically designed for use on acrylic finishes. If Meguiar's is not available, an acrylic polish of equal quality or automotive paste wax is acceptable. Never use abrasive household cleaners on any Jacuzzi Whirlpool Bath product.
General Whirlpool Bath Troubleshooting Guide PROBLEM Pump/Motor does not start. PROBABLE CAUSES REMEDY No power to pump/motor. Reset GFCI. Pump/motor not plugged in. Insert plug fully into outlet. Magic Touch switch - air tube not connected to switch or to air switch on pump/motor. Reconnect tube to Magic Touch switch or to air switch pump/motor. Pump/motor faulty. Replace pump/motor assembly. Jets are closed. Open jets by rotate counterclockwise. Suction cover may be clogged.
Authorized Service If you need a referral for a service company near you, or need assistance with operation or maintenance related questions, please call our Service Support Department at 1-866-905-2289. For service agent listing, visit our web site at http://www.jacuzzi.com/. To find the service agent listings, click on “For The Trade”. Then click on Electrical/ Mechanical Service Agents. Depending on the problem, click on “Electrical/Mechanical Repairs” or “Finish, Surface or Shell-Related Problems”.
REPAIR PARTS NOTE: When a part number has 3 Xs, substitute the appropriate color code for the Xs: 940 White 914 Almond 969 Oyster BMH JET BMH JET ASSEMBLY 8489XXX 1 POSITION AIR CONTROL RETAINER NOZZLE 8412XXX NOZZLE BHM 8413XXX O RING 8488000 INTERNAL O RING SEAT 8487XXX KNOB 8267XXX JET BODY 8411XXX GRAPHIC RING AIR 8263000 LOCK NUT 8415000 SCREWS (2) 7514000 PANEL, 1 POSITION D851XXX AIR CONTROL ASSEMBLY U767000 SCREWS (4) 9724000 14 Jacuzzi Whirlpool Bath© U961000F 12/04
REPAIR PARTS 2 POSITION CONTROLLER (AIR & PUMP/MOTOR ON/OFF) BEZEL 8247XXX KNOB 8267XXX BUTTON AIR ACTUATOR 8246XXX (MOTOR/PUMP ON/OFF) GRAPHIC RING AIR 8263000 GRAPHIC RING ON/OFF 8262XXX PANEL 2 POSITION 8241XXX BELLOWS C377000 AIR CONTROL ASSEMBLY U767000 CUP C841000 SCREWS (8) 9724000 15 Jacuzzi Whirlpool Bath© U961000F 12/04
REPAIR PARTS SUCTION ASSEMBLY HTC JET HTC ASSEMBLY B785XXX SCREWS (3) 9356000 CLAMPING RING B788XXX SCREW #10-24/2 3959000 SWIVEL HTC B786XXX SUCTION COVER/GASKET ASSEMBLY 6651XXX GASKET 1840000 SUCTION FITTING 1958000 HTC BODY A320XXX RING BACK-UP SUCTION 2136000 BACKUP RING 1836000 LOCKNUT 1643000 LOCKNUT 1835000 Jet Body BG15000 Stop (Part of Jet Body) Fitting BG00XXX Nozzle (Part of Jet Body) Adjustable Handle BM01XXX Back Massage Jet Assy 16 Jacuzzi Whirlpool Bath© U961000F 12/04
REPAIR PARTS 3 POSITION PANEL BUTTON AIR ACTUATOR 8246XXX KNOB 8267XXX (2) BEZEL 8247XXX GRAPHIC RING AIR (2) 8263XXX GRAPHIC RING ON/OFF 8262XXX 3 POSITION PANEL 9224XXX BELLOWS C377000 AIR CONTROL ASSEMBLY U767000 (2) SCREWS (10) 9724000 CUP C841000 17 Jacuzzi Whirlpool Bath© U961000F 12/04
REPAIR PARTS RAPIDHEAT REPAIR HEATER DISCHARGE SIDE U394000 (SHOWN) UNION GASKETS (2) Y671000 UNIONS (2) Y670000 SUCTION SIDE S749000 UNION GASKETS (2) G947000 UNIONS (2) T180000 NOTE: Suction heater components and Discharge heater components are not interchangable. HEATER BLANK MOTOR/PUMP ASSEMBLY 7.
Jacuzzi Whirlpool Bath Limited Warranty Espree Series Bath Product WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Espree Series Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the unit or its equipment in accordance with the following terms and conditions.
RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In the event of a problem, the unit must not be installed.
