SUMMER RAIN™ II 2 PERSON SHOWER SYSTEM ONE WALL INSTALLATION AND OPERATING INSTRUCTIONS Jacuzzi Whirlpool Bath© BY82000 03/05
IMPORTANT SAFETY INFORMATION Do not place or use electrically connected devices, such as television, radio, or stereo speakers, lights, hair dryers, or telephones, within 1.5 m (5 feet) of shower. Note: This is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation according to codes are required for proper installation and user satisfaction. We recommend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath© products.
CONTENTS Specifications _________________________________________________________________________ 2 Enclosure Specifications ________________________________________________________________ 3 Rough-in Reference ____________________________________________________________________ 3 Component Identification ________________________________________________________________ 4 Base Installation _______________________________________________________________________ 5-7 Tower and Doors Installation ______________
SPECIFICATIONS Important: Read complete instructions before beginning installation. Each unit arrives ready for installation, equipped with base, glass and associated hardware. Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Immediately upon receipt, inspect the base and other components before installing. Check all carton inserts for parts and hardware.
ENCLOSURE SPECIFICATIONS 84" 72" 48" FRONT VIEW SIDE VIEW ROUGH-IN REFERENCE 72" 1" TILE FLANGE BLOWER MOTOR FOR UNITS WITH AIR 38-15/16" 27-11/16" 48" AIR LINE FOR UNITS WITH AIR 36" TOP VIEW 3 Jacuzzi Whirlpool Bath© BY82000 03/05
COMPONENT IDENTIFICATION SIDE SUPPORT RAIL CENTER SUPPORT RAIL WATER TOWER DOOR POST AIR TOWER DOOR POST WATER TOWER GLASS SIDE PANEL RAIL BRACKET AND COVER CAP WALL POST SEAT GLASS SIDE PANEL GLASS DOORS BASE FRONT VIEW SIDE VIEW WALL POST WALL POST GLASS SIDE PANEL GLASS SIDE PANEL SEAT BASE WATER TOWER WATER TOWER DRAIN DOOR POST DOOR POST AIR TOWER GLASS DOORS (SUPPORT AND SIDE SUPPORT RAILS NOT SHOWN) 4 Jacuzzi Whirlpool Bath© BY82000 03/05
BASE INSTALLATION PRELIMINARY ROUGH-IN INSTALLATION INSTRUCTIONS The floor structure beneath the unit must be able to support a total weight of the unit and bather. Refer to page 2, SPECIFICATIONS, for weight specifications . Refer to COMPONENT IDENTIFICATION on page 4 to help identify parts. STEP 2 Remove the stainless steel strainer from the drain assembly. Disassemble the locknut and two gaskets from the back of the drain assembly.
BASE INSTALLATION STEP 4 Before installing the base, make sure the 4 water supply hoses are routed to seat area. If you have a with Air unit also route the air supply hose to the seat area. If you have a with Air unit also pull the 2 flow switch cables and the control panel cable through base at this time. With the drain fitting passing over the center of the drainpipe, lower the shower base carefully into place, push down firmly until the base is in place.
BASE INSTALLATION STEP 7 STEP 8 Place cement board or equivalent on top of shower base flange and secure to studwall. Filling the area marked DO NOT FILL will prevent moisture from properly draining back into the base through weep holes. This moisture is due to leakage through the tile grout. Sealing the tile grout will reduce or prevent this leakage. Apply tile (or other finishing material) leaving a 1/8" gap between the finishing material and the shower base flange lip.
TOWERS AND DOORS INSTALLATION THESE INSTRUCTIONS ARE FOR SUMMER RAIN UNITS WITH AND WITHOUT AIR FEATURE OPTION. REFER TO COMPONENT IDENTIFICATION ON PAGE 4 TO HELP IDENTIFY PARTS. WATER TOWER DETAIL FLOW SWITCH CABLE* All wall finish tiling, trim, and sealing should be completed before beginning this part of the installation. BOLT (5/16") WASHER STEP 1 Position each tower on mounting pad on base. For the shower towers, feed hot and cold supply line through appropriate holes in bottom of tower.
TOWERS AND DOORS INSTALLATION STEP 4 Take the side support rails and install a cover cap and wall bracket on each end. Place the center support rail into slot on each tower. If rail does not readily fit into slots, it may be necessary to loosen the bolts holding towers to base (it may only be necessary to loosen one tower). DO NOT FORCE CENTER RAIL INTO SLOTS. With center support rail in position, install hold down brackets but do not tighten screws.
TOWERS AND DOORS INSTALLATION STEP 5 Two shut-off valves are provided per water tower. To hook up supply lines, unscrew valves from braided line. Using thread sealant, screw each valve to stub out at bottom of tower. Then reconnect braided line using provided gasket. Do not twist or kink supply lines when connecting. Perform this step for both water towers.
TOWERS AND DOORS INSTALLATION STEP 6 Move the door assembly to the door post on water tower and slide the assembly into the door post. Locate the base of the door into the slot of serrated door positioner that positions the hinge barrel as shown. STEP 7 Check that the magnetic mouldings on door and air tower overlap. Insert adjusting bolt with locking nut into fixed nut in top cap (See below).
TOWERS AND DOORS INSTALLATION STEP 9 Position the fixed glass wall post so that the glass side panel will be parallel with the outside edge of the base. The fixed glass wall post position may vary slightly due to the anchored location of the water tower. STEP 11 Slide fixed glass panel all the way into wall post. FINISH WALL GLASS SIDE PANEL MOUNTED PARALLEL TO EDGE OF BASE EDGE OF BASE STEP 10 Level the post in its proper position and mark where screw holes are to be drilled.
TOWER AND DOOR INSTALLATION STEP 13 Install glazing gasket on fixed glass walls post and jambs on the outside. Note orientation of gasket. Soapy water may help to insert the glazing gasket. NOTE: The glazing is to be installed on the outside of enclosure for both wall posts and tower jambs. Clean any soapy residue off the glass and towers. On the inside of enclosure, apply sealant to entire length of glass and wall post as well as the entire length of the glass and tower jamb.
TOWERS AND DOOR INSTALLATION STEP 16 Install handles as shown. Note orientation of handle. Hand tighten knob. Flat screw has a screw driver notch. Do not over tighten either knob or flat screw as cracked glass may result. STEP 14 Install fixed glass cover cap on wall post. COVER CAP INTERIOR OF SHOWER LARGE WASHER WASHERS GLASS DOOR DOOR HINGE STEP 15 Install all towers' top cover STEP 17 Turn on water supply and check for leaks. Correct any leaks before continuing the installation.
TOWERS AND DOOR INSTALLATION STEP 19 Seal all around all bases of towers with sealant. Also seal the inside of both wall posts, jambs, door posts and bottom of both glass side panels on the inside only.
OPERATION SHOWER TOWERS Shower Head There are three selectable positions: Jet, Normal Pulsating, and Aerated flow. Body Sprays (2 Upper and 2 Lower) To adjust the flow and intensity, turn as shown. The spray can also be turned to change the direction of the spray. Shower Head LESS FLOW AND INTENSITY MORE FLOW AND INTENSITY Body Sprays (2 Upper & 2 Lower) Diverter Control To turn ON water, turn the inner knob clockwise and adjust for more or less flow.
OPERATION AIR TOWER Air Jet (12) Controller AIR TOWER CONTROLS ON/OFF BUTTON INCREASE TEMPERATURE AIR FLOW LED AIR TEMPERATURE LED DECREASE TEMPERATURE AIR TEMPERATURE AIR FLOW CONTROLLER To turn ON press ON/OFF button or turn ON water at either shower tower. The unit will then automatically go into a preheat cycle to heat the air transmission pipes. There will be a 5 (five) minute pause while the system preheats. During this time both LEDs will be ON.
MAINTENANCE To remove any lime scale from the shower head and body sprays, rub with your finger the outer ring of nozzles on the shower head and all nozzles on the body spray. To clean the foot temperature tester, unscrew the nozzle and back flush the wire mesh filter. Do not use metal tools (such as scissors or screwdrivers, etc.) to clean the body sprays, shower head or foot temperature tester. To clean the base, simply use a mild, nonabrasive liquid detergent solution.
TOWER FIXTURES REPAIR PARTS 1 (5X) 2 (5X) 3 (5X) 4 TOWER ASSEMBLY 9 (5X) 10 6 5 11 (4X) 7 (PART OF U547000) 8 12 13 14 15 16 17 PART OF D709827 18 WASHER (PART OF D709827) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19.
TOWER PLUMBING REPAIR PARTS ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2 18 1 11 QTY. 1 3 4 3 2 1 1 1 1 1 2 1 1 1 1 2 2 4 1 PART NO. Y221000 U401000 Y724000 7164000 0455000 7269000 7269000 U547000 Y723000 7269000 U405000 7269000 7269000 7269000 U137827 U540000 GASKET U421000 U400000 4 5 4 7 3 6 18 10 19 9 14 3 18 5 2 4 12 13 8 3 16 11 18 17 2 15 20 Jacuzzi Whirlpool Bath© BY82000 03/05 DESCRIPTION TOWER, 2 PERSON SHOWER FTG, ELL, .
21 Jacuzzi Whirlpool Bath© BY82000 03/05
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath© has obtained applicable code (standards) listings generally available on a national basis for products of this type. It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product. Jacuzzi Whirlpool Bath© makes no representation or warranty regarding, and will not be responsible for any code compliance.
Jacuzzi Whirlpool Bath Limited Warranty Designer Collection Shower Product WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer Collection Bath Product (“unit”) who purchases the product for personal or single family use (“user”). The Company will repair or replace, at its option, the unit or its equipment in accordance with the following terms and conditions.
RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In the event of a problem, the unit must not be installed.
