EXPERIENCE MANUAL Pure Air® Whirlpool Salon® Spa Jacuzzi Luxury Bath 14525 Monte Vista Avenue Chino, CA 91710 1-800-288-4002 www.jacuzzi.
Table of Contents General Operation Information......................................................................................................................................... 2 Reference Illustration for a Pure Air® System.................................................................................................................. 3 Pure Air® Operation................................................................................................................................................
English Experience Reference Illustration for a Pure Air® System These illustrations are for reference only, as the unit comes fully assembled. DANGER: RISK OF ELECTRIC SHOCK! Before servicing these connections, disconnect all power supply cables to both 120 VAC services. J2 Control Panel Pure Air® Schematic Diagram 120 VAC 15A Dedicated GFCI Circuit Required Fig. 2 CONTROL PANEL G BLOWER J4 Control Panel Pure Air® Schematic Diagram 120VAC 15A Dedicated GFCI Circuit Required Fig.
English Experience Pure Air® Operation J2 Pure Air® Controls Fig. 4 G • Press once to turn ON. • Press again to turn OFF. NOTE: The last blower setting used is remembered by the system and will automatically resume upon next use. • Press to increase the blower intensity • Alternately, you can press and hold the button to increase the intensity level. • Press to decrease the blower intensity • Alternately, you can press and hold the button to decrease the intensity level. J4 Pure Air® Controls Fig.
English Experience Pure Air® Auto-Dri™ Air Channels To remove accumulations of bathtub residue from the whirlpool system, it is recommended that a Whirlpool bathtub be cleaned at least twice a month. For best results, however, we recommend that you clean your Whirlpool bathtub after each use using Systems Clean™, our exclusive two-part plumbing system cleaner made specifically for Whirlpool bathtubs.
English Experience Reference Illustration for a Whirlpool System J2 Control Panel Whirlpool Schematic Diagram Fig. 6 120VAC 20A Dedicated GFCI Circuit Required CONTROL PANEL PUMP/MOTOR G G 120VAC 15A Dedicated GFCI Circuit Required CONTROL BOX 120 VAC OR PUMP PUMP/MOTOR PUMP FOR MODELS WITH IN-LINE HEATER J2 Control Panel Whirlpool with Chromatherapy Schematic Diagram PUMP/MOTOR Fig.
English Experience Reference Illustration for a Whirlpool System (Continued) J4 Control Panel Whirlpool Schematic Diagram Fig.
English Experience Whirlpool Operations (Continued) J4 Whirlpool Controls Fig. 11 NOTE: When switching between functions, the LED for the inactive functions will dim and the active function will brighten.
English Experience Whirlpool Operations (Continued) Controlling Whirlpool Direction & Flow CAUTION: Never run the whirlpool system with all the jets closed. To adjust the direction of the jets: • To change the direction of the water flow, swivel the jet nozzle to the desired angle, Figure 12. To adjust the water flow to the jets: • Increase the force of the flow by rotating the nozzle or jet face to the left (counterclockwise).
English Experience Cleaning Systems Clean™ To remove accumulations of bathtub residue from the whirlpool system, it is recommended that a Whirlpool bathtub be cleaned at least twice a month. For best results, we recommend that you clean your Whirlpool bathtub after each use using Systems Clean™, our exclusive two-part plumbing system cleaner made specifically for Whirlpool bathtubs. Systems Clean™ is available through an authorized Jacuzzi Luxury Bath distributor or by calling us direct at 1-800-288-4002.
English Experience Reference Illustration for a Salon® Spa System J4 Control Panel Salon® Spa Schematic Diagram Fig.
English Experience Salon® Spa Operations J4 Salon® Spa Controls Fig.
English Experience Troubleshooting Procedures PROBLEM PROBABLE CAUSES REMEDY Pump/motor does not start • No power to pump/motor • Pump/motor not plugged in • Pump/motor faulty • • • • Pump/motor operates but no fully adjustable jets are functioning • Jets are closed • Suction cover/strainer may be clogged • Open jets by rotating counter-clockwise • With the motor turned OFF, remove the suction cover/strainer and remove any debris.
English Experience Notes: ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________ ________________________________________________________________________________________________
