TD0301 User Manual Interface Key Button Key Illustrate Power On/Off, power on after press 3 seconds; power off after press 3 seconds WPS On/Off, enable/disable the WPS function of Wi-Fi after press 3 seconds Reset Software reset after short click Reload to default settings after press 6 seconds Hardware reset after press 12 seconds LED Indication Indicator Working status WiFi LED Blue light active for Wi-Fi enabled Blue light flash quickly for the WPS function is enabled Off for Wi-Fi disabled
Installation Follow the diagram to install the SIM card. Tips: Always switch the device off and disconnect the charger before removing the SIM card. 1. Remove the back cover. 2. Insert the SIM card. Ensure that the contact area on the card is facing down and that the beveled corner on the card is facing the beveled corner on the holder. 3. Finally cover the back. Charge Your battery has been partially charged at the factory. If the device indicates a low charge, do the following: 1.
Two：Using USB port TD0301 Usage TD0301 supports 4G/3G/2G networks. Insert the SIM card, Wi-Fi devices and the computers can access the Internet through TD0301, enjoy high-speed network services. Smart phones, tablet computers, game consoles and other Wi-Fi devices can be connected with the TD0301 Wi-Fi connection for Internet access. Computers & laptops etc. may be connected to the TD0301 via USB cable for Internet Access.
In order for a Wi-Fi device to establish a connection with the TD0301 for the first time, you will need to select the TD0301SSID (Wi-Fi name) & enter the relevant Wi-Fi password, which you may find them in the following ways: Method one: on the nameplate view the default SSID and Wi-Fi password Method Two: Login management page view 1. On computer, open your browser, input http://192.168.0.1 and enter.
★Recommend that you start using TD0301 administration pages after setting a convenient landing memorizing SSID and a higher safety factor Wi-Fi passwords. Install the driver and connecting the device USB Connection:Windows 10 for example 1. Keep TD0301 powering on, Plug the device into your computer,it will install the default RNDIS driver automatically. 2.
Establish Wi-Fi connection:you must ensure that the computer equipped with a wireless network card. If the computer showed the presence of Wi-Fi connectivity, the wireless LAN is available. Otherwise, you need to check your wireless network card is working properly. In the Wi-Fi list, select the SSID consistent with TD0301 Wi-Fi, click Connect. Then enter the correct Wi-Fi password, click ok. A moment later, Wi-Fi connection is displayed next to the name, Wi-Fi connection is successful.
1. Enter the correct Wi-Fi password, click Next 2. After a moment, the prompt “Connected” is displayed below the name, it means the connection is established.
WebUI ● Home First part of the main display network connection status, connected devices and data, system message, such as IPaddress, system run time, traffic statistics, SIM card status, type and quality of the network signal, whether it is roaming, with or without a new message, and so on.
You can quickly set network type, parameters and Wi-Fi settings through the wizard function.
● Wi-Fi 1. General You can setup the Wi-Fi related information in this page,such as SSID, password, B/G/N mode,Channeland so on. 2. WPS WPS (Wi-Fi Protected Setup) provides easy and secure establishment of a wireless network. You can configure WPS here via the PIN code or the WPS button,premise is your wireless card support WPS function. TD0301 supports three kinds of WPS authentication:AP PIN, WPS Buttonand Client PIN Code. Default is WPS Button.
●AP PIN authentication: You can click button “Generate New PIN “to get a PIN, then share it to your wireless client to connect TD0301. ●WPS Buttonauthentication: The first scenario: Please click the WPS button on this interface (or press the physical WPS button on the router), then press the WPS button on the wireless client and wait for about 2 minutes to make the connection.
Youcan press the WPS button on theTD0301 until the Wi-Fi light flash quickly, to activate the WPS, then you can see connecting process. ●Client PIN Code: Start the client WPS process and get the client PIN code. Enter the client's PIN code on the Client PIN code field and click Start. Please check the user manual of your wireless client to see if it supports the WPS function.
3. Wi-FiMAC Filter Wireless MAC filter allows you to control packets from devices with specified MAC address in your Wireless LAN. You can enable or disable this function onthis page. ●Accept Mode:It only allows the devices in the list to connect to the router. ●Reject Mode: The devices which mac addressin the filter list will be prohibited connect to the TD0301. 4. ClientList This page displays the currently connected clients and their respective MAC addresses in the list.
● LAN 1.LAN IP This section allows you to configure the local network settings of your router. ●IP Address: The IP address of router. ●Subnet Mask:The subnet mask for router. ●Domain Name: You can specify a domain name for router to instead of IP address to login this management UI. 2.DHCP Server DHCP (Dynamic Host Configuration Protocol) is a protocol for the automatic configuration used on IP networks.
3. Client List This page displays the currently connected clients and their respective MAC addresses in the list. ● Cellular 1.Connection Set up the cellular network related information.
Cellular:You can customize the network configuration or manually add the new APN and set default APN. ConnectionSetting:You can set allow data roaming or not. And you also can set Connection Mode. ●AutoMode: When you turn on TD0301 without additional operations, the device will connect to the networkautomatically. ●Manual Mode:You need to connect to the network manually after opening theTD0301 management page. 2.
●Preferred Network:You can set preferred networkonthis page, the default is Auto, and other options are GSM, WCDMA, and LTE. ●PLMN: Default is Auto. If you select Manual, you should click button Searchto get available networks and choose one to register by manual. 3. PIN Management When you enable the PIN function of your SIM card, if you reboot the device, you need to login management page,and the page will promptyou to enter the correct PIN code, then you can use the SIM card.
You can send to no more than 5 numbers and 10 text messages at same time, the phone number is separated by „,‟. Also you can setting the SMS center, storage location of messages, and so on. 5.
● Firewall 1.General Enable the firewall to protect your local area network against attacks from hackers. The firewall filters the incoming and outgoing packets based on the filter rules. ●Enable Firewall: You can enable or disable the firewall function. Default is disable. Also you can setting the matching packets rule to receive or reject. ●Enable Ping From WAN:Enable or disable ping function for WAN. Default is disable. 2. URL Filter Key in the keywords for the sites that you want to block.
3.IP Filter IP Filter blocks the LAN to WAN packet exchanges and restricts devices from using specific network services. For example, if you do not want the device to use the Internet service, key in 80 in the destination port. The traffic that uses port 80 will be blocked (but https cannot be blocked). Leave the source IP field blank to apply this rule to all LAN devices. Black List Duration: During the scheduled duration, clients in the Black List cannot use the specified network services.
● System 1.System Change the router login password, time zone, and NTP server settings. ●System: You can modify the login password for administrator interface. Also you can setting the time to logout the UI automatically. ●Basic Config: Config time zone and NTP server. ●Remote Access Config: Enable or disable remote access, and set IP address, port.
2. Firmware Upgrade You can upgrade the firmware on this page. Click “Upload” button to get the file which extension name is “bin” file to upgrade. NOTE: Do not disconnect the power adapter or interrupt the update process. Your device will reboot when the update is complete. 3.Restore/Save/Upload This function allows you to save current settings to a file, or load settings from a file. If you want to restart the device anyway, it is better done via the "Reboot" button.
configuration pages will be restored to the factory defaults. ●Save Setting:Save the current settings to a file. ●Restore Setting:Restore the settings from a file. ●Reboot Setting:Restart router. 4.System Log This page shows the detailed system's activities. 5.Scheduled Tasks This feature allows you to reset the Internet connection on your router by periodically resetting the connection, by configuring the options on this page to proceed on a predetermined schedule.
6.Power Management Your MiFi device can switch to low-power Standby mode when idle. To exit Standby mode, press the power button. Power Management ● Suspend: Set the time to enter into standby mode,when there is no Wi-Fi client connected to router. “Never” is disable this function. ●Deep Sleep: Set the time to enter into deep sleep mode, when there is no Internet access and no Wi-Fi client connected to this device.“Never” is disable this function.
●Battery Status: Indicate the battery status. 7. Device Information This page can view related equipment information. Warning ·Please only use original accessories provided with purchase. Use of unauthorized chargers or other accessories may cause damage to the device and can result in fire, explosions, or other hazards. ·Please keep the device in a dry and cool environment and do not let the device come into contact with water. Extreme high or low-temperatures may cause damage to the device.
charger from the device and unplug the charger from the power outlet. ·The built-in battery is non-removable. Please do not attempt to change or disassemble the battery by yourself. This may result in damage to the battery or the device. The battery can only be replaced by an official authorized service provider. Notice: Using the wrong model of battery may result in an explosion. Please make sure to dispose of used batteries as instructed.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
