Specifications

ManualsBrandsJACS Solutions ManualsElectronicsWireless charging pad

TG0803 Wireless Charger Module Specifications

Module launch synopsis：

Transmitter Module for wireless charger is a transmitter designed specifically for

non-QI standard wireless reception requirements. The module doesn’t meet

WPC1.1standard. Using chips from Shenzhenheshen Technologies Co Ltd, it has

advantages of Stable performance, and low power consumption, etc. The unique

PWM modulation mode is adopted that transfer efficiency get markedly improved.

The convenient of wireless can easy implementation, module output efficiency is

high, compared with the wireless Built-in transmitting power and wireless receiving

power, it can control the loss of emission energy more accurately. The number of

module components is small that have high performance cost ratio, after the

debugging can implement “install and play”. This can easily satisfactory the various

demands of customers, and it’s perfect for doesn’t meet QI standards for various

types of wireless charging equipment. For instance：used in Bluetooth devices with

wireless charging function 、 table computer 、 electric toothbrush 、 cosmetic

instrument、waterproof electronic equipment、electric automobile, etc. this IC can

drive up to 10KW power, at present.

ONE. Module features

1：Stringent enforcement design with safe as the core, incompatible with QI various

standard reception；

2：The module equipped with overcurrent protection, short-circuit protection, FOD ,

Summary of content (9 pages)

PAGE 1
TG0803 Wireless Charger Module Specifications Module launch synopsis： Transmitter Module for wireless charger is a transmitter designed specifically for non-QI standard wireless reception requirements. The module doesn’t meet WPC1.1standard. Using chips from Shenzhenheshen Technologies Co Ltd, it has advantages of Stable performance, and low power consumption, etc. The unique PWM modulation mode is adopted that transfer efficiency get markedly improved.
PAGE 2
etc. 3: The standby power is less than 200MA when 5V input ,efficiency were around 65%72% , temperature rise is small； TWO. Product dimensions PCBA Module F63*1.0mm dimensions Magnetic sheet Φ70*3.5mm and coil dimensions Module weight THREE. Electrical features Supply voltage 5V2A Wireless output 5V 1.3A voltage and current Transmitting 125KHZ frequency Standby current <200MA Wireless distance 2MM-6MM The coil type Silk-covered wire 2.
PAGE 3
Transfer 70% efficiency Temperature adjustable protection Defensive Over-temperature overcurrent short circuit FOD function Directive function LED Working 0-60℃ 10%-85% temperature and humidity Storage -20-80℃ 10%- 95% temperature and humidity FOUR.
PAGE 4
I NO. Test Item Required Tested value Conclusion value 1 On-load 5.
PAGE 5
II second, the green light goes off. Green light illuminates and blue light goes off at reception, take off the load blue light illuminate. 10 Cell phone Nothing signal interference test 11 Transmitting 1~4mm receiving distance 12 Detection no-load of No abnormalities and load any noise 13 Full load normal starting 14 Standby consumes 0.06A~0.
PAGE 6
III power automatically FIVE. LED Instructions state LED STAND-BY INDICATO DEVIATION CHARGING END OF THE FOD STATE STATE CHARGING NOT NOT NOT BRIGHT BRIGHT BRIGHT BRIGHT BRIGHT BRIGHT R BLUE BRIGHT LIGHT GREEN NOT LIGHT BRIGHT BLINKING NOT BRIGHT SIX. Module working description 1：Put the tablet PC near the center of the transmitter coil , the green LED on the module will light up, the tablet PC should have voltage and current input, the green LED light is stand for charging.
PAGE 7
IV 4：If the module detects an exception on the tablet PC receiver, The module will stop working, at this point, you need to move the tablet PC away from the launch, put the tablet PC on the launch module again to enter the charging state. SEVEN．The usage environment of wireless charger A. LAUNCHING BASE 1、The principle of wireless charging is to convert direct current into electromagnetic field, and then send the electromagnetic field up. The general launch distance is 2-7MM.
PAGE 8
V 5、Other terminal devices are placed on the TG0803 wireless charging base, there are different responses depending on terminal equipment, the device on the phone type will display the charge icon, but there is no current input. Some devices are placed on the launch base will be directly identified as foreign matter, at this point, the launch base will directly enter the foreign body protection state, and the blue light flashing. B.
PAGE 9
VI This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.