Brochure

ManualsBrandsJacob ManualsBrass / Nickel LocknutsCable Gland Locknut M20

Setting Standards

Signal Connectors M 23

Summary of content (32 pages)

PAGE 1
Setting Standards Signal Connectors M 23 63
PAGE 2
Product Overview 64 Housings page 66 Inserts page 74 Accessories page 82 Dimensions and specifications may be changed without prior notice
PAGE 3
Technical Data M 23 Signal Connectors Mechanical Data Materials and Technical Data Housing Copper-Zinc alloy Die Casting Housing surface Nickel plated other surface upon request Inserts (for contacts) Thermoplastic Polyamid PA 6 (Nylon 6/6), PBT Contacts Brass Alloy Contact surface at point of contact Nickel and gold plated (0,25µm Au) Minimum mating cycles > 1000 Seals / O-Rings Buna-N standard optional Viton® (Viton is a registered trademark of DuPont) Temperature range -40° C – 125° C (
PAGE 4
Signal Connectors M 23 / Housing Straight Connector, Female Thread Cable-Ø Part Number 3 – 7 mm (.12 – .28“).........7.106.400.000 7 – 12 mm (.28 – .47“)......7.106.500.000 11 – 17 mm (.44 – .67“).....7.106.600.000 Ø 26,2 64,7 24 24 Contacts and inserts page 74 • Assembly instructions page 88 Straight Connector, Male Thread Cable-Ø Part Number 3 – 7 mm (.12 – .28“).........7.206.400.000 7 – 12 mm (.28 – .47“)......7.206.500.000 11 – 17 mm (.44 – .67“).....7.206.600.
PAGE 5
Signal Connectors M 23 / Housing Right Angle Connector, Female Thread with positioning Part Number 3 – 7 mm (.12 – .28“).........7.300.300.000 5 – 10 mm (.20 – .39“).......7.300.400.000 7 – 12 mm (.28 – .47“).......7.300.500.000 10 – 14 mm (.39 – .55“).....7.300.600.000 24 68,3 50 Cable-Ø 24 22 Ø 26,2 Contacts and inserts page 74 • Assembly instructions page 89 Cable-Ø Right Angle Connector, Female Thread, EMC with positioning Part Number 7 – 12 mm (.28 – .47“).......7.301.500.
PAGE 6
Signal Connectors M 23 / Housing Panel Connector, Male Thread, Front Mounting Type Ø 2,7 / Ø 3,2 M 2,5 / M 3 25 19,8 22,5 21,5 M 23 x 1 Panel hole Ø 19,8 Ø 20 + 0,1 4 4 4 4 Part Number holes Ø 3,2 mm (.13“) .....7.400.000.000 threads M 3 ....................7.402.000.000 holes Ø 2,7 mm (.11“) .....7.404.000.000 threads M 2,5 .................7.406.000.
PAGE 7
Signal Connectors M 23/ Housing ALE FOR M LY TS ON INSER 23,5 Optional: Flat gasket, jam nut M 20 x 1,5 / PG 13,5 M 23 x 1 24 19,1 + 0,1 Front mounting for male inserts Thread M 20 x1,5 ..............7.420.000.000 Thread PG 13,5 .................7.422.000.
PAGE 8
Signal Connectors M 23 / Housing Right Angle Panel Connector, Male Thread Type 4 holes 2,7 mm (.11“).........7.435.000.000 Optional: Flat gasket 25 19,8 M 23 x 1 29 16,5 34,5 Ø 2,7 Part Number Easy fixation with M 2,5 screws Ø 19,8 Panel hole 50 Ø 20 + 0,1 Right Angle Panel Connector, Male Thread, rotating Contacts and inserts page 74 • Assembly instructions page 93 Type Part Number 335° rotating, hole mounted Thread M 20 x 1,5 .............7.431.000.
PAGE 9
Signal Connectors M 23 / Housing holes Ø 3,2 mm (.13“) .....7.450.000.000 threads M 3 ....................7.452.000.000 holes Ø 2,7 mm (.11“) .....7.454.000.000 threads M 2,5 .................7.456.000.000 M 23 x 1 22,5 4 4 4 4 Panel Connector, Male Thread, Rear Mounting Part Number Optional: Flat gasket Ø 2,7 / Ø 3,2 M 2,5 / M 3 25 Ø 20,5 Type Panel hole max.
PAGE 10
Signal Connectors M 23 / Housing Panel Connector with Radius Flange Type M 23 x 1 Ø 34 30,5 51,6° With anti-vibration O-Ring and flat body gasket Ø 58 mm (2.28“) ...............7.490.000.000 23 28 for countersunk head screws M 3 Part Number 3,5 Ø 58 Contacts and inserts page 74 • Assembly instructions page 91 / 92 Panel Connector with Radius Flange Type M 23 x 1 Ø 34 30,5 43° With anti-vibration O-Ring and flat body gasket Ø 70 mm (2.76“) ...............7.491.000.
PAGE 11
Signal Connectors M 23 / Housing Type Signal Distribution Part Number T 01 .................................7.T01 M 23 x 1 M 23 x 1 52,2 Ø 26,2 78 Contacts and inserts page 74 Type Signal Distribution Part Number T 02 .................................7.T02 56,5 Ø 26,2 M 23 x 1 74 M 23 x 1 Contacts and inserts page 74 Signal Distribution In case of so called Flying Connections it is often required to distribute, cross or combine signals.
PAGE 12
Signal Connectors M 23 / Inserts / Pinouts Inserts 6-pole Type Part Number Part Number Pinout clockwise Pins Sockets Insert with solder contacts .........7.001.906.103.................7.001.906.104 Insert without contacts...............7.003.906.101.................7.003.906.102 Insert pin mating view (Part E) Insert with dip solder contacts Length 3,5 mm .........................7.001.906.107 Insert with dip solder contacts Length 10 mm ..........................7.001.906.127.................7.001.
PAGE 13
Signal Connectors M 23 / Inserts / Pinouts Type Part Number Part Number Inserts 9-pole (8 + 1) Pinout clockwise Pins Sockets Insert with solder contacts .........7.001.981.103.................7.001.981.104 Insert without contacts...............7.003.981.101.................7.003.981.102 Insert with dip solder contacts Length 3,5 mm .........................7.001.981.107 Insert pin mating view (Part E) Insert with dip solder contacts Length 10 mm ..........................7.001.981.127................
PAGE 14
Signal Connectors M 23 / Inserts / Pinouts Inserts 12-pole Type Part Number Part Number Pinout clockwise Pins Sockets Insert with solder contacts .........7.001.912.103.................7.001.912.104 Insert pin mating view (Part E) Insert with solder contacts +PE (Pos.9)..............................7.001.912.113.................7.001.912.114 Insert without contacts...............7.003.912.101.................7.003.912.102 Insert without contacts +PE (Pos.9)..............................7.003.912.111.
PAGE 15
Signal Connectors M 23 / Inserts / Pinouts Type Part Number Inserts 16-pole Part Number Pinout clockwise Pins Sockets Insert with solder contacts .........7.001.916.103.................7.001.916.104 Insert without contacts...............7.003.916.101.................7.003.916.102 Insert with dip solder contacts Length 3,5 mm .........................7.001.916.107 Insert pin mating view (Part E) Insert with dip solder contacts Length 10 mm ..........................7.001.916.127.................7.001.
PAGE 16
Signal Connectors M 23 / Inserts / Pinouts Inserts 17-pole Type Part Number Part Number Pinout counter-clockwise Pins Sockets Insert with solder contacts .........7.002.917.103.................7.002.917.104 Insert without contacts...............7.004.917.101.................7.004.917.102 Insert pin mating view (Part P) Insert with dip solder contacts Length 3,5 mm .........................7.002.917.107 Insert with dip solder contacts Length 10 mm ..........................7.002.917.127................
PAGE 17
Signal Connectors M 23 / Required Contacts Number of Poles Contact Arrangement Required Contacts 6 ...................................................................................6 x 2 mm 7 ...................................................................................7 x 2 mm 9 (8 + 1) ..........................................................................8 x 1 mm .....................................................................................1 x 2 mm 12 ..............................
PAGE 18
Signal Connectors M 23 / Contacts Contacts Type Crimp Range Part Number Crimp pin 1 mm, machined .......0,08 – 0,56 mm2 (AWG 28 – 20) .7.010.901.031 Crimp pin 1 mm, machined .......0,14 – 1 mm2 (AWG 26 – 17) .....7.010.901.001 Crimppin 1 mm, machined ........0,75 – 1,5 mm2 (AWG 17 – 16) ..7.010.901.021 Crimp socket 1 mm, machined ...0,08 – 0,56 mm2 (AWG 28 – 20) ..7.010.901.012 Crimp socket 1 mm, machined ...0,34 – 1 mm2 (AWG 22 – 17) .....7.010.901.002 Crimp socket 1 mm, machined ...
PAGE 19
Signal Connectors M 23 / Contacts Type Crimp Range Part Number Contacts Crimp socket 1,5 mm, machined..0,14 – 0,56 mm2 (AWG 26 – 20)..7.010.901.512 Crimp socket 1,5 mm, machined..0,56 – 1 mm2 (AWG 20 – 17) .....7.010.901.502 Crimp pin 2 mm, machined .......0,75 – 2,5 mm2 (AWG 18 – 14) ..7.010.902.001 Crimp socket 2 mm, machined ...0,75 – 2,5 mm2 (AWG 18 – 14)..7.010.902.
PAGE 20
Signal Connector / Accessories Accessories Type Part Number Plastic protective cap for connectors with male thread .........................................7.000.900.101 for connectors with female thread.......................................7.000.900.102 Brass protective cap for connectors with female thread............................................................7.010.900.103 Brass protective cap for connectors with male thread ..............................................................7.010.
PAGE 21
Signal Connector / Accessories Type Part Number Accessories Crimp tool for manual crimping of machined crimp contacts for signal connectors ........................................................7.000.900.904 Operating instructions on page 84 - 86, 94 Adaptor flange for Straight Connectors .....................................................7.010.900.128 Adapter for Conduit Fittings Type Snapflex 16.......................7.010.900.204 DN 12 ..............................7.010.900.205 Snapflex 20.
PAGE 22
Crimp Tool for Signal Connectors M 23 / M 16 Crimp Tool Type Part Number Crimp tool............................................................7.000.900.904 / 7.000.900.907 Application The four indent crimp tool 7.000.900.904 / 7.000.900.907 has been developed for optimal crimping of machined contacts with diameters from 0.08 to 2.5 mm2 (28 through 14 AWG).
PAGE 23
Crimp Tool for Signal Connectors M 23 / M 16 Crimp Tool Adjustment of Crimp Depth Crimp depth can be adjusted as follows: Turn the adjusting screw clockwise for reducing the crimp depth and counter-clockwise for increasing the crimp depth. Adjustment Increments: ^ adjustment by 0.01 mm - 1 space on the adjusting screw = - 1 full rotation of adjusting screw ^ = adjustment by 0.
PAGE 24
Crimp Tool for Signal Connectors M 23 Crimp Tool Setting for HUMMEL Crimp Contacts (Crimp Tool 7.000.900.904) Cross Section (mm2) AWG Crimp Tool Setting mm Locator Setting Crimp pin 1 mm 0,14 0,25 0,34 0,50 0,75 1,00 AWG 26 AWG 24 AWG 22 AWG 20 AWG 18 AWG 17 0,70 0,76 0,82 0,90 1,00 1,10 1 7.010.901.012 Crimp socket 1 mm (0,08 – 0,56 mm2) 0,08 0,14 0,25 0,34 0,56 AWG 28 AWG 26 AWG 24 AWG 22 AWG 20 0,75 0,78 0,82 0,86 0,90 2 7.010.901.
PAGE 25
Crimp Tool for Signal Connectors M 23 Crimp Tool Setting for HUMMEL Crimp Contacts (Crimp Tool 7.000.900.904) Part Number Crimp Contact 7.010.901.031 Crimp pin 1 mm 7.010.901.021 7.010.901.
PAGE 26
Signal Connectors M 23 / Assembly Instructions Straight Connector, Male / Female Thread 1. max. 25 mm 2. 4 mm 3. Crimp 4. 5. click click 6. 7. Code 8.
PAGE 27
Signal Connectors M 23 / Assembly Instructions Right Angle Connectors, EMC click 1. 60 mm 7. 2. 8. 3. 9. Code 4 mm 4. 25 10. Crimp 5. 11. click 12. cli ck 6.
PAGE 28
Signal Connectors M 23 / Assembly Instructions Right Angle Connector, rotating, EMC 1. 65 mm click 2. 7. Crimp 8. 3. 4. 4 mm Code 9. Crimp 10. click 5. 27 click 11. 6. 12.
PAGE 29
Signal Connectors M 23 / Assembly Instructions Panel Connectors, Male Inserts 1. 4 mm 3. 2. Crimp click 4. click 5. 6.
PAGE 30
Signal Connectors M 23 / Assembly Instructions Panel Connectors, Female Inserts 1. 2. 4 mm Crimp 3. click 4. click 5. Code 6.
PAGE 31
Signal Connectors M 23 / Assembly Instructions 1. 4 mm Right Angle Panel Connector 5. 2. Crimp 6. 3. click 4. click 7.
PAGE 32
Crimping, Assembly and Disassembly of Contacts Crimping, Assembly and Disassembly of Contacts Crimping - Remove conductor insulation 4 mm (.16“) max. - Select appropriate Crimp tool setting (see page 86) - Insert Crimp contact into the positioner of the tool - Insert stripped end of conductor into the crimp opening of the contact - Squeeze handles of crimp tool together Assembly - Open crimping jaws and remove contact - Pry open upper and lower insert approx.