HOT WATER SANITIZING UNDERCOUNTER DISHMACHINE TECHNICAL MANUAL FOR JACKSON MODEL: JP-24BPNSU DESCRIPTION, OPERATION, INSTALLATION AND MAINTENANCE INSTRUCTIONS An November 11, 2005 P/N 7610-002-38-50 (Revision D) Company Jackson MSC Inc. P.O. BOX 1060 HWY. 25E BARBOURVILLE, KY. 40906 PHONE (606) 523-9795 FAX (606) 523-9196 www.jacksonmsc.
MANUFACTURERS WARRANTY ONE YEAR LIMITED PARTS & LABOR WARRANTY ALL NEW JACKSON DISHWASHERS ARE WARRANTED TO THE ORIGINAL PURCHASER TO BE FREE FROM DEFECTS IN MATERIAL OR WORKMANSHIP, UNDER NORMAL USE AND OPERATION FOR A PERIOD OF (1) ONE YEAR FROM THE DATE OF PURCHASE, BUT IN NO EVENT TO EXCEED (18) EIGHTEEN MONTHS FROM THE DATE OF SHIPMENT FROM THE FACTORY.
REVISION REVISION DATE MADE BY APPLICABLE ECN A 02-13-01 CBW 5700 B 03-26-03 MAW N/A Replaced photos with drawings, Added new logo. C 01-21-04 MAW N/A Added 2nd Enodis logo to cover. D 11-11-05 MAW 6964, 6988 7006, 7383 DETAILS Release to production Changed thermostat from 05930-121-71-36 to 05930-011-49-43. Added 4-3/4” Din Rail 05700-002-90-18 to Control Box Assembly. Changed thermostat bracket from 05700-011-73-72 to 05700-01181-64.
NOMENCLATURE FOR THE MODEL COVERED IN THIS MANUAL JP-24BPNSU JP-24BPNSU - Hot water sanitizing, electrically-heated dishmachine. Model: Serial No.: Installation Date: Service Rep. Name: Phone No.: JP-24BPNSU Technical Manual 7610-002-38-50 Rev.
APPROVAL AND PROCUREMENT RECORD APPROVAL DATA FOR: TITLE OF MANUAL: DESCRIPTION, OPERATION, INSTALLATION, AND MAINTENANCE INSTRUCTIONS FOR DISHWASHING MACHINE, MODEL JP-24BPNSU APPROVAL AUTHORITY: (LETTER OF APPROVAL FROM PROCURING ACTIVITY CONTRACT NO. DLA-400-90-M-1376 NSN 7320-01-144-2638 NO.
CHANGE RECORD Change No. Date Title/Brief Description Signature of Validating Officer JP-24BPNSU Technical Manual 7610-002-38-50 Rev.
IDENTIFYING TECHNICAL PUBLICATION SHEET 1. PURPOSE: This technical publication is issued for the purpose of identifying and authorizing the following commercial manual for Navy use. MANUFACTURER: Jackson MSC Inc., Barbourville, Kentucky 40906 PURCHASE ORDER OR CONTRACT NO.: DLA-400-90-M-1376 EQUIPMENT: Dishmachine, Model JP-24BPNSU ADDITIONAL IDENTIFICATION (if any): Not applicable DATE: 1 January 1991 2.
TABLE OF CONTENTS SECTION I. DESCRIPTION PAGE SPECIFICATION INFORMATION Specifications Dimensions 2 3 INSTALLATION & OPERATION INSTRUCTIONS Installation Instructions Electrical Installation Instructions Deck Mounting of Dishmachine Detergent Control Operation Instructions 5 6 7 8 9 III. PREVENTATIVE MAINTENANCE 11 IV. TROUBLESHOOTING 13 V.
SECTION 1: SPECIFICATION INFORMATION 1
SECTION 1: SPECIFICATION INFORMATION SPECIFICATIONS PERFORMANCE/CAPABILITIES ELECTRICAL REQUIREMENTS OPERATING CAPACITY (RACKS/HOUR) WASH PUMP MOTOR HORSEPOWER RACKS PER HOUR 21 DISHES PER HOUR 525 GLASSES PER HOUR 525 3/4 WATER REQUIREMENTS HEATER HEATER MOTOR TOTAL RATINGS AMPS AMPS AMPS VOLTS HERTZ PHASE OPERATING CYCLE (SECONDS) 460 60 3 480/8.2KW 9.4 1.6 11 460 60 3 480/10KW 12 1.6 13.6 WASH TIME 120 INLET TEMPERATURE 140°F RINSE TIME 15 GALLONS PER HOUR 52.
SECTION 1: SPECIFICATION INFORMATION DIMENSIONS 2 1/2” Legend: A - Drain Connection flexible hose. 6’-0” free length, 1” ID x 1 3/8” OD B - Electrical Connection. C - Water Inlet 1/2” Female Pipe Thread, 2 1/2” AFF D - Detergent Feeder Connection MIN. WALL CLEARANCE 12” 22 5/8” B C 19” 16 3/4” 24 1/4” A 33 3/4” D 13 1/4” 8 1/2” 2 1/4” 3 3/4” 2 3/4” 4 1/4” C Note: All dimensions from floor can be increased 1” with adjustable feet supplied.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS 4
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS INSTALLATION INSTRUCTIONS VISUAL INSPECTION: Before installing the unit, check the container and machine for damage. A damaged container is an indicator that there may be some damage to the machine. If there is damage to both the container and machine, do not throw away the container. The dishmachine has been inspected and packed at the factory and is expected to arrive to you in new, undamaged condition.
SECTION 2: INSTALLATION/OPERATION INSTRUCTIONS ELECTRICAL INSTALLATION INSTRUCTIONS ELECTRICAL POWER CONNECTION: Electrical and grounding connections must comply with the applicable portions of the National Electrical Code ANSI/NFPA 70 (latest edition) and/or other electrical codes. Disconnect electrical power supply and place a tag at the disconnect switch to indicate that you are working on the circuit. The dishmachine data plate is located on the right side and to the front of the machine.
SECTION 2: INSTALLATION & OPERATION INSTRUCTIONS INSTALLATION INSTRUCTIONS (CONTINUED) DECK MOUNTING OF THE DISHMACHINE: The dishmachine must be secured in place using the deck mounting tracks and caps provided with machine. Install the (4) adjustable feet provided into screw holes where shipping bolts were removed earlier. Adjust the level of the dishmachine by screwing the adjustable feet in or out. The front of the machine should be adjusted 1/4” to 1/2” higher than the back.
SECTION 2: INSTALLATION & OPERATION INSTRUCTIONS DETERGENT CONTROL Detergent usage and water hardness are two factors that contribute greatly to how efficient your dishmachine will operate. Using detergent in the proper amount can become, in time, a source of substantial savings. A qualified water treatment specialist can tell you what is needed for maximum efficiency from your detergent, but you should still know some basics so you’ll understand what they are talking about.
SECTION 2: INSTALLATION & OPERATION INSTRUCTIONS OPERATION INSTRUCTIONS PREPARATION: Before proceeding with the start-up of the unit, verify the following: 1. The strainer is in place and is clean. 2. That the wash and rinse arms are screwed securely into place and that their endcaps are tight. The wash and rinse arms should rotate freely. POWER UP: To energize the unit, turn on the power at the service breaker. The voltage should have been previously verified as being correct.
SECTION 3: PREVENTATIVE MAINTENANCE 10
SECTION 3: PREVENTATIVE MAINTENANCE PREVENTATIVE MAINTENANCE The dishmachines covered in this manual are designed to operate with a minimum of interaction with the operator. However, this does not mean that some items will not wear out in time. There are many things that operators can do to prevent catastrophic damage to the dishmachine. One of the major causes of component failure has to do with prescrapping procedures.
SECTION 4: TROUBLESHOOTING 12
SECTION 4: TROUBLESHOOTING SECTION COMMON PROBLEMS WARNING: Inspection, testing and repair of electrical equipment should be performed only by qualified service personnel. Certain procedures in this section require electrical tests or measurements while power is applied to the machine. Exercise extreme caution at all times. If test points are not easily accessible, disconnect power, attach test equipment and reapply power to test. When replacing electrical parts, disconnect power at source circuit breaker.
SECTION 4: TROUBLESHOOTING SECTION COMMON PROBLEMS Problem: Rinse water not at required temperature range. 1. Thermometer is defective. Replace. 2. Thermostat is defective. Adjust the thermostat. Replace if necessary. Problem: Machine doesn’t drain when “OFF/DRAIN” switch is pressed. 1. 2. 3. 4. 5. Drain solenoid clogged. Remove obstruction. Defective “OFF/DRAIN” switch. Replace. Defective motor or motor start relay. Replace. Defective drain solenoid. Replace. Defective timer. Replace.
SECTION 5: SERVICE PROCEDURES 15
SECTION 5: SERVICE PROCEDURES RINSE SOLENOID VALVE REPAIR PARTS KIT These dishmachines are equipped with electrical solenoid valves to allow for automatic fill and rinse. These valves are designed to specific tolerances and design aspects that must be met in order to function properly.
SECTION 5: SERVICE PROCEDURES RINSE SOLENOID VALVE REPAIR PARTS KIT (CONTINUED) Loosening the conduit nut Prying open the coil wire cover 4. When replacing the coil, ensure that when removing the coil wire cover that care is taken not to damage the wires inside. Using the medium flathead screwdriver, gently use it to open the cover enough to where it could be pulled off. 7. Using a pair of channel locks, gently loosen the conduit retaining ring for the conduit nut.
SECTION 5: SERVICE PROCEDURES RINSE SOLENOID VALVE REPAIR PARTS KIT (CONTINUED) Removing the valve bonnet Removing the diaphragm 13. Slowly remove the valve bonnet. Note: The spring for the plunger is located directly under the bonnet and may come free if you are not careful. Remove the plunger, spring and valve bonnet and place to the side. 17. Remove the diaphragm retainer and then the diaphragm itself.
SECTION 5: SERVICE PROCEDURES RINSE SOLENOID VALVE REPAIR PARTS KIT (CONTINUED) 21. With the mesh screen removed, look down into the valve and verify it is not clogged. Remove any foreign objects from the valve body that would obstruct flow. 22. Reassemble the valve, reversing the steps needed to take it apart. Replace defective replacement parts with new parts from ordered kits. Ensure that components are sufficiently tightened to prevent leakage.
SECTION 5: SERVICE PROCEDURES VACUUM BREAKER REPAIR PARTS KIT These dishmachines are equipped with vacuum breakers to serve as back-flow prevention devices. ASSE requirements specify what type of back-flow prevention is necessary on dishmachines. Vacuum breakers, unlike air gaps, have certain parts that have specific tolerances and design aspects that must be met in order to function properly.
SECTION 5: SERVICE PROCEDURES VACUUM BREAKER REPAIR PARTS KIT (CONTINUED) 7. If any of these conditions are present, replace the old plunger with the new one from your kit. Verify that the new plunger is also free from defects. If it is not, contact your Ecolab representative immediately. 8. The plunger should drop into the vacuum breaker and seat. Ensure it is not flipped upside down (the orange seal ring should be up towards the top of the vacuum breaker). 9. Pick up the cap and examine it.
SECTION 5: SERVICE PROCEDURES REPLACING THE PUMP MOTOR/REPLACING THE HEATER REPLACING THE PUMP MOTOR The following list of tools will be needed to complete this procedure. 5/6” nutdriver, phillips screwdriver, 7/16” socket and ratchet, and 7/16” wrench. 1. Disconnect the electrical power to the dishwasher at the main circuit breaker box when servicing. Place a tag on the circuit box indicating the circuit is being repaired. 2. Disconnect power and conduit from dishmachine terminal block. 3.
SECTION 5: SERVICE PROCEDURES REPLACING THE DRAIN VALVE REPLACING THE DRAIN VALVE The following list of tools will be needed to complete this procedure. 5/16” nutdriver, flat screwdriver, phillips screwdriver, and 7/16” socket and ratchet. 1. Disconnect the electrical power to the dishwasher at the main circuit breaker box when servicing. Place a tag on the circuit box indicating the circuit is being repaired. 2. Disconnect the power and conduit from dishmachine terminal block. 3.
SECTION 6: PARTS SECTION 24
SECTION 6: PARTS SECTION ELECTRICAL PANEL ASSEMBLY 1 2 3 4 3 5 6 7, 8 9 10 13 11, 12, 5 14, 5 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 QTY 1 1 2 2 9 1 1 3 1 1 1 1 1 1 1 2 1 1 1 4 15, 16 17 DESCRIPTION Bushing, Snap Track, Terminal 6 7/8" End Clamp Contactor, Mini Screw, 10-32 x 3/8” Phillips Truss Round Head Track, Terminal 3 3/4" Decal, L1, L2, L3 Block, Snap-in Terminal Electrical Control Panel Weldment Grommet, 1 1/8" Heyco Wire Lug Ground Decal Overload, Contactor ACME Tran
SECTION 6: PARTS SECTION GAUGE PANEL ASSEMBLY 1 2 3 4 5 6 Dielectric Cover, Electrical Panel 05700-011-40-48 7 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15 QTY 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 8 9 10 11 12 13 14 DESCRIPTION Gauge, 0-100 PSI with Green Zone Fitting, 1/4” BARB, 1/4” FNPT Swivel Hose, 5/16” x 12" Fitting, 1/4” BARB 1/4” MNPT Swivel Control Panel Decal, Control Panel Thermometer, 96” Wash Thermometer, 48” Rinse Switch, ON/FILL & OFF/DRAIN Light, Red Switch, Delime Light, Amber Light,
SECTION 6: PARTS SECTION KICK PLATE ASSEMBLY Dielectric Cover, Kickplate Panel 05700-011-40-49 Nut, Nylon Wing, 1/4”-20 05310-994-01-00 Decal, Power Disconnect Warning 09905-021-47-07 Kickplate Weldment 05700-041-86-40 Control Panel Only 09330-041-85-00 JP-24BPNSU Technical Manual 7610-002-38-50 Rev.
SECTION 6: PARTS SECTION INCOMING PLUMBING ASSEMBLY 6 7 4 2 5 8 2 3 2 7 1 ITEM 1 2 3 4 5 6 7 8 9 QTY 1 3 1 1 1 1 2 1 1 9 DESCRIPTION Y-Strainer, 1/2" Adapter, 1/2" Ftg x Male Tee, 1/2” x 1/2” x 1/4” Ball Valve, Test Cock 1/4" Valve, Solenoid 1/2" 110 volt Union, 1/2" C to C Elbow, 1/2" C to Ftg Copper Tube, 1/2" x 18 1/2" Elbow, 1/2", 90 Deg. C to MSPS Mfg. No.
SECTION 6: PARTS SECTION PLUMBING ASSEMBLY (CONTINUED) Plug, 1/4” Brass 3 per machine 04730-209-01-00 Vacuum Breaker 04820-003-06-13 Injector Weldment 05700-031-41-83 Adapter, 1/2" Ftg. x Male 04730-401-03-01 Copper Tube, 1/2” x 20 1/4” 05700-031-41-83 Adapter, 1/2" Ftg.
SECTION 6: PARTS SECTION PLUMBING ASSEMBLY (CONTINUED) Clamp, Hose 04730-719-06-09 Hose, 3/4” x 8 1/2” 05700-011-38-83 Locknut, 1/4”-20 S/S Hex with Nylon Insert 05310-374-01-00 Gasket, Rinse 05330-111-42-81 Rinse Stiffener Weldment 05700-002-59-79 Gasket, Rinse 05330-111-42-81 Rinse Hub Weldment 05700-021-38-31 Locknut, 1/4”-20 S/S Hex with Nylon Insert 05310-374-01-00 JP-24BPNSU Technical Manual 7610-002-38-50 Rev.
SECTION 6: PARTS SECTION 1/2” SOLENOID VALVE & 1/2” NPT VACUUM BREAKER REPAIR PARTS KITS Screw Data Plate Cap Screw Coil & Housing 06401-003-07-43 Data Plate Valve Bonnet Spring & Plunger Kit 06401-003-07-40 Cap Cap Retainer Diaphragm Retainer Diaphragm & O-ring Kit 06401-003-07-41 O-Ring Plunger Screen Retainer Components of Repair Kit 06401-003-06-23 Body Mesh Screen Valve Body Complete 110 Volt Solenoid Valve Assembly 04810-100-12-18 Complete Vacuum Breaker Assembly 04820-003-06-13 JP-24BPN
SECTION 6: PARTS SECTION DRAIN VALVE ASSEMBLY 17 15 13 18 11 10 5 16 4 3 1 3 6 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 QTY 1 1 1 1 1 4 1 1 1 1 1 2 1 1 4 1 4 1 4 12 8 DESCRIPTION Diverter Valve Assembly, 220 Volt Valve, With Brackets Hosebarb, 1” x 3/4” NPT Polypropylene Hosebarb, 90° 1” x 3/4” NPT Plate, Motor Mounting Weldment Tricnut, 10-32 AK Fastener, S/S Lockwasher, #10 External Tooth Grommet, Heyco Cam Weldment Plate, Dielectric Switch, Micro Screw, 4-40 x 5/8" Motor, Chemic
SECTION 6: PARTS SECTION DRAIN PLUMBING ASSEMBLY 1 2 7 8 1 9 3, 10 4 5 6 6 ITEM 1 2 3 4 5 6 7 8 9 10 QTY 1 1 2 1 1 1 2 2 1 2 DESCRIPTION Clamp, 3/16” to 1 1/2” Hose, Formed Drain Bolt, 10-32 x 1/2 Slotted Truss Head Diverter Valve Assembly Clamp, 11/16” to 1 1/4” Hose, 1” I.D. x 10 Feet Long Locknut, 1/4”-20 S/S Hex with Nylon Insert Bolt, 1/4”-20 x 1/2” Long Bracket, Valve Mounting with Tricnuts Washer, #10 External Tooth Star Mfg. No.
SECTION 6: PARTS SECTION WASH MOTOR TO WASH TUB ASSEMBLY 1 2 3 5 4 6 8 9 10 12 4 11 - NOT SHOWN 7 4 11 - NOT SHOWN ITEM 1 2 3 4 5 6 7 8 9 10 11 12 QTY 1 1 1 4 1 1 1 1 1 4 6 4 DESCRIPTION Hub, Discharge Machined Gasket, 2” O.D. x 1 1/2” I.D. x 1/16” Nut, Jam 1 1/2”-12 NPT Hose Clamp, 1 1/16" - 2” Hose,1 1/4” x 2 1/4” Reinforced Motor, Wash Hose, Bottom Manifold Pump Gasket, Suction Adapter Casting, Suction Adapter Washer, S/S 1/4”-20 I.D. Locknut, 1/4”-20 S/S Washer, 1/4” I.D. x 3/4” O.D. S/S Mfg.
SECTION 6: PARTS SECTION WASH MOTOR ASSEMBLY Wash Pump Impeller 04320-021-44-02 Mechanical Seal 05330-011-44-06 Motor Only 06105-002-64-03 Complete Assembly 460 Volt, 3/4 Hp 06105-121-60-06 Wash Pump Gasket 05330-011-44-08 Test Cock Pump Casing Only 05930-021-44-07 JP-24BPNSU Technical Manual 7610-002-38-50 Rev.
SECTION 6: PARTS SECTION RINSE TANK & COMPONENTS Rinse Tank Weldment 05700-031-38-09 Secured with: Locknut, 1/4”-20 S/S Hex with Nylon Insert 05310-374-01-00 Dielectric Cover 05700-011-40-50 Fitting, 1/4” Imperial Brass 05310-924-02-05 Nut, 5/16”-18 S/S Hex 05310-275-01-00 Lockwasher, 5/16” Split 05311-275-01-00 Gasket, Heater 05330-011-47-79 The JP-24BNSU comes supplied with various heaters, depending on the characteristics of the machine.
SECTION 6: PARTS SECTION DOOR ASSEMBLY 15 Order this entire assembly using: 05700-011-39-15 2 To order the Operation/Instruction Decal 09905-021-41-49 14 11 6 5 8 7 9 18 13 12 1 4 10 3 16 17 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 QTY 1 1 1 1 1 1 2 6 2 1 1 1 1 1 12 1 2 2 DESCRIPTION Door Handle, S/S Seal Channel, Inner Door, Left Outer Door Weldment Right Hinge Assembly Weldment Spray Baffle Left Hinge Assembly Weldment Spacer, Hinge UHMW Fastener, Screw, 1/4"-20 x 1-1/2" Long Hing
SECTION 6: PARTS SECTION MISCELLANEOUS DOOR SUB-ASSEMBLIES Door Latch Assembly 05700-011-44-41 Door Latch Casting 05700-011-44-40 Latch Roller 05700-011-44-38 Latch Spring 05700-011-44-39 Door Spring 05340-011-44-58 Hinge Retaining Plate 05700-011-44-37 Door Switch 05930-303-38-00 Switch Plate 05700-011-44-22 Stop, Right Hinge 05700-021-37-68 Stop, Left Hinge 05700-021-37-67 Hinge Components secured with: Locknut, 1/4”-20 S/S Hex with Nylon Insert 05310-374-01-00 Cover, Right Hinge Weldment 05700-
SECTION 6: PARTS SECTION RINSE ARM & WASH ARM ASSEMBLIES Plug, Rinse Arm 04730-609-04-00 Rinse Arm Assembly 05700-031-39-21 Rinse Arm 05700-031-38-30 Bearing, Rinse Head 03120-002-72-24 Bushing, Rinse Head 05700-021-33-84 Washer, Rinse Arm 05330-011-42-10 Ring, Retaining 05340-112-01-11 Wash Arm Assembly 05700-021-39-23 Wash Arm Weldment 05700-021-46-58 Bearing Assembly 05700-021-35-97 O-ring (Not Shown) 05330-002-60-69 JP-24BPNSU Technical Manual 7610-002-38-50 Rev.
SECTION 6: PARTS SECTION MISCELLANEOUS PARTS Back Panel 05700-031-44-33 Guide, Right Rack 05700-031-37-88 Guide, Left Rack 05700-031-37-89 Strainer Spacer 05700-021-35-83 Attaches with: Nut, Nylon Wing, 1/4”-20 05310-994-01-00 Strainer Weldment 05700-031-35-81 JP-24BPNSU Technical Manual 7610-002-38-50 Rev.
SECTION 6: PARTS SECTION FRAME, SHROUD, & PANEL COMPONENTS Shroud Weldment 05700-031-38-15 Left Frame Weldment 05700-011-73-85 Secured with 10-32 x 1/2” Long Screws 05305-173-04-00 Right Frame Weldment 05700-011-73-86 The swivel feet used on the unit may be ordered using 05340-108-02-00 Top Panel 05700-041-38-38 Left Dress Panel 05700-041-38-37 Right Dress Panel 05700-041-38-08 The Panels are secured with 10-32 x 1/2” Truss Head Screws, 05305-011-39-36 JP-24BPNSU Technical Manual 7610-002-38-50 Rev
SECTION 7: ELECTRICAL DIAGRAMS 42
SECTION 7: ELECTRICAL DIAGRAMS JP-24BPNSU (460 VOLT, 60 HERTZ, THREE PHASE) 9905-031-51-11 JP-24BPNSU Technical Manual 7610-002-38-50 Rev.
Ref: NAVSEAINST 4160.3A NAVSEA S0005-AA-GYD-030/TMMP (Insert Classification of TMDER Here) CLASSIFICATION: NAVSEA/SPAWAR TECHNICAL MANUAL DEFICIENCY/EVALUATION REPORT (TMDER) INSTRUCTION: Continue on 8 1/2" x 11" paper if additional space is needed. 1. USE THIS REPORT TO INDICATE DEFICIENCIES, PROBLEMS, AND RECOMMENDATIONS RELATING TO PUBLICATION. 2. FOR CLASSIFIED TMDERS. SEE OPNAVINST 5510H FOR MAILING CLASSIFIED TMDERS. 3. Submit TMDERS at web site 1. PUB NO. http://nsdsa.nswses.navy.mil or mail 2.
FOLD HERE DEPARTMENT OF THE NAVY PLACE POSTAGE HERE COMMANDER NSDSA CODE 5E30 NAVSURFWARCENDIV 4363 MISSILE WAY PORT HUENEME CA 93043-4307 FOLD HERE 45
Ref: NAVSEAINST 4160.3A NAVSEA S0005-AA-GYD-030/TMMP (Insert Classification of TMDER Here) CLASSIFICATION: NAVSEA/SPAWAR TECHNICAL MANUAL DEFICIENCY/EVALUATION REPORT (TMDER) INSTRUCTION: Continue on 8 1/2" x 11" paper if additional space is needed. 1. USE THIS REPORT TO INDICATE DEFICIENCIES, PROBLEMS, AND RECOMMENDATIONS RELATING TO PUBLICATION. 2. FOR CLASSIFIED TMDERS. SEE OPNAVINST 5510H FOR MAILING CLASSIFIED TMDERS. 3. Submit TMDERS at web site 1. PUB NO. http://nsdsa.nswses.navy.mil or mail 2.
FOLD HERE DEPARTMENT OF THE NAVY PLACE POSTAGE HERE COMMANDER NSDSA CODE 5E30 NAVSURFWARCENDIV 4363 MISSILE WAY PORT HUENEME CA 93043-4307 FOLD HERE 47
SECTION 8: JACKSON MAINTENANCE & REPAIR CENTERS 48
SECTION 8: JACKSON MAINTENANCE & REPAIR CENTERS ALABAMA TO FLORIDA ALABAMA: CALIFORNIA: COLORADO: DELAWARE (cont.): JONES-McLEOD APPLIANCE SVC 1616 7TH AVE. NORTH BIRMINGHAM, AL 35203 (205) 251-0159 800-821-1150 FAX: (205) 322-1440 service@jones-mcleod.com BARKERS FOOD MACHINERY SERVICES 5367 SECOND STREET IRWINDALE, CA 91706 (626) 960-9390 800-258-6999 FAX: (626) 337-4541 service@barkers.
SECTION 8: JACKSON MAINTENANCE & REPAIR CENTERS GEORGIA TO MARYLAND GEORGIA: ILLINOIS (cont.): IOWA: KENTUCKY (cont.): GCS SERVICE INC 3127 PRESIDENTIAL DRIVE ATLANTA, GA 30340 (770) 452-7322 800-334-3599 FAX: (770) 452-7473 GENERAL PARTS INC. 248 JAMES ST. BENSONVILLE, IL 60106 (630) 595-3300 800-880-3604 FAX: (630) 595-0006 GOODWIN-TUCKER GROUP 3509 DELAWARE AVENUE DES MOINES, IA 50313 (515) 262-9308 800-372-6066 FAX: (515) 262-2936 goodwintuc@aol.
SECTION 8: JACKSON MAINTENANCE & REPAIR CENTERS MARYLAND TO NEW YORK MARYLAND (cont.): MINNESOTA: MONTANA: NEW JERSEY: EMR SERVICE DIVISION 2626 PITTMAN DRIVE SILVER SPRING, MD 20910 (301) 588-8080 800-348-2365 FAX: (301) 588-6985 baltparts@emrco.com GENERAL PARTS INC. 11311 HAMPSHIRE AVE. S. BLOOMING, MN 55438-2456 (612) 944-5800 800-279-9980 FAX: (800) 279-9980 RESTAURANT APPLIANCE SVC. 7219 ROOSEVELT WAY NE SEATTLE, WA 98115 (206) 524-8200 800-433-9390 FAX: (206) 525-2890 info@restappl.
SECTION 8: JACKSON MAINTENANCE & REPAIR CENTERS NEW YORK TO PENNSYLVANIA NEW YORK (cont.): NEW YORK (cont.): NORTH DAKOTA: OKLAHOMA: APPLIANCE INSTALLATION AND SERVICE CORP. 1336 MAIN STREET BUFFALO, NY 14209 (716) 884-7425 800-722-1252 FAX: (716) 884-0410 ais@worldnet.att.net A. I. S. COMMERCIAL PARTS & SVC 7387 PITTSFORD VICTOR RD. ROCHESTER, NY 14610 (716) 461-2370 800-458-4198 FAX: (716) 461-5545 GCS SERVICE INC. 2857 LOUISIANA AVENUE N.
SECTION 8: JACKSON MAINTENANCE & REPAIR CENTERS PENNSYLVANIA TO VIRGINIA PENNSYLVANIA (cont.): SOUTH CAROLINA: TENNESSEE (cont.): UTAH: ELMER SCHULTZ SVC. 540 NORTH 3RD STREET PHILADELPHIA, PA 19123 (215) 627-5400 FAX: (215) 627-5408 elmer2@erols.com AUTHORIZED COMMERCIAL EQUIPMENT SERVICE 1811 TAYLOR ST. COLUMBIA, SC 29202 (803) 254-8414 FAX: (803) 254-5146 GCS SERVICE INC. 748 FESSLERS LANE NASHVILLE, TN 37210 (615) 244-8050 800-831-7174 FAX: (615) 244-8885 GCS SERVICE INC. 817 N. THIRD STREET P.O.
SECTION 8: JACKSON MAINTENANCE & REPAIR CENTERS VIRGINIA TO WYOMING/CANADA VIRGINIA (cont.): WYOMING: GCS SERVICE INC. RICHMOND, VA 800-822-2303 HAWKINS COMMERCIAL APPLIANCE SERVICE 300 S. WYANDOT ST. ENGLEWOOD, CO 80110 (303) 781-5548 (800) 624-2117 FAX: (303) 761-5561 johns@hawkinscommercial.com WASHINGTON: RESTAURANT APPLIANCE SVC 7219 ROOSEVELT WAY, NE SEATTLE, WA 98115 (206) 524-8200 800-433-9390 FAX: (206) 525-2890 info@restappl.com WEST VIRGINIA: STATEWIDE SERVICE, INC. 603 MAIN AVE.
