Installation Instructions

GSM autoalarm CA-1202 „Athos“ 2/4 MHF52505
Figure 1: installation of the car alarm in Mode 1
6.1 Programming sequences
Enter the prescribed spaces in SMS texts as shown in the table below. MASTER is a factory default master code, which should be changed to your own password. All SMS texts are case insensitive.
SIM entry* Text of SMS instruction Description RESET 1 MASTER RESET EN 1 Mode setting. Factory default is 0 – no function (immobilization relay copies ignition). Note: By
performing the RESET EN x instruction, all settings, remote controllers and enrolled wireless detectors will be erased! RESET is indicated by four siren chirps.
Not possible MASTER UC uuuu
User Code setting – the code (password) allows you to operate the alarm remotely via SMS from unauthorized phones. uuuu is a new user code, up to 8 letters (A –Z & 0 – 9). Factory default user code is USER
Not possible MASTER MC xxxx Master Code setting, xxxx is a new master code, up to 8 characters (A –Z & 0 – 9).
The code allows you to change settings for the car alarm. Factory default master code is MASTER
TEL1 xx...x MASTER TEL1 xx...x TEL2 xx...x MASTER TEL2 xx...x TEL3 xx...x MASTER TEL3 xx...x TEL4 xx...x MASTER TEL4 xx...x
Setting of phone numbers to report alarms (these phones will also be authorized to control the alarm via SMS without a user password) E.g.: MASTER TEL2 [phone] will enter the phone number to TEL2 memory MASTER TEL3 0 will erase the TEL3 memory.
DIAL1 xx...x MASTER DIAL1 xx...x DIAL2 xx...x MASTER DIAL2 xx...x DIALA xx...x MASTER DIALA xx...x DIALB xx...x MASTER DIALB xx...x
Setting of phone numbers to dial using Hands free. E.g.: MASTER DIAL2 [phone] will enter the number to DIAL2 memory (which is dialed after you press button 2 on the remote control) MASTER DIAL2 0 will erase the memory DIAL2.
DIP abcdefghij MASTER DIP abcdefghij DIP parameters entry – see part 7 SET abcdefghi MASTER SET abcdefghi SET parameters entry – see part 8 Not possible MASTER LEARN RC Remote Control enrollment - up to 4 controllers can be enrolled, turn the ignition key on before
sending the instruction. To enroll a remote control press and hold buttons A and B together for 3 seconds. After you enroll all remote controls, turn the ignition key off.
Not possible MASTER LEARN JA JA-60 wireless detector enrollment – up to 8 detectors can be enrolled, turn the ignition key on
before sending the instruction. To enroll a detector insert its battery. After you enroll all detectors, turn the ignition key off.
Not possible
MASTER TXT 01,text Editing of SMS texts (reports and instructions), see part 10
TELU xx...x MASTER TELU xx...x Sustained call setting (for pre-paid cards) 1x month the xx..x number is called, call duration 10 s.
* See part 5 for details.
GSM car alarm CA-1202 „Athos“ 3/4 MHF52505 7 DIP parameters By SMS: MASTER DIP ABCDEFGHIJ you can change 10 features:
Description
DIP
0 1
A 0 = Silent arming/disarming without siren chirps
1 = 10 ms siren chirps when arming/disarming (non backed-up siren) 2 = 20 ms siren chirps when arming/disarming (backed-up siren)
B Silent alarm
Audible alarm (30 sec.)
C
SMS alarm report only
SMS alarm report + siren sound phone call
D SMS remote control not
confirmed by SMS reply
SMS remote control instructions confirmed by SMS reply
E
0 = arming control by dialing in from TEL1 to TEL4 disabled 1 = arming control by dialing from TEL1 enabled 2 = arming control by dialing from TEL1 and TEL2 enabled 3 = arming control by dialing from TEL1, TEL2 and TEL3 enabled 4 = arming control by dialing from all TEL1 to TEL4 enabled Arming and disarming by dialing from authorized phones is free of charge
F
Arming control by dialing in is not confirmed by SMS
Arming control by dialing in (see E) is confirmed by SMS to the phone which dialed the car alarm
G
User can not change SMS texts
User can change SMS texts by TXT sequence
H
REARM disabled
If the car is not entered within 1 minute after disarming, it will REARM
I
0 = Immobilization by arming and by SMS instruction
1 = Immobilization by arming and automatically 5 minutes after ignition is
turned off and also by SMS instruction
2 = Immobilization only by SMS instruction
J
Self-location disabled
The car´s location will be sent by SMS to all TEL1 to TEL4 if there is an alarm or if the car stops after immobilization SMS instruction (See 13.6.)
Factory default setting is DIP 1111000000 (bold letters in the text). If you want to change only particular parameters, enter x for the others (i.e. MASTER DIP 0xxxxxxxxx will make arming control silent). 8 SET parameters By SMS: MASTER SET ABCDEFGHI you can change 9 features:
Description
SET
0 1
A
Open door arming indication disabled
Audible indication of arming with open door (4 beeps)
B
Voltage detector disabled
Voltage drop detector enabled
C
lock / unlock signal duration 0 = 0,3 / 0,3 sec 1 = 4 / 4 sec 2 = 60 / 0,3 sec (automatic window closing)
D
DOOR input logic: 0 = automatic 1 = activated by falling edge (grounding) 2 = activated by rising edge (disconnecting from GND)
E INP1 logic:
0 = automatic 1 = activated by falling edge (grounding) 2 = activated by rising edge (disconnecting from GND)
F INP2 logic:
0 = automatic 1 = activated by falling edge (grounding) 2 = activated by rising edge (disconnecting from GND)
G no function in Mode1
H no function in Mode1
I no function in Mode1
Factory default setting SET 100000010 (bold letters in the text). If you want to change only particular parameters, enter x for the others (i.e. MASTER SET 0xxxxxxxx will disable open door arming indication). 9 User instructions
9.1 Remote control arming and disarming
Button A of the remote control is used for arming, B for disarming (arming
control is confirmed by a siren chirp).
9.2 Remote control by SMS instructions
SMS instructions sent from an authorized phone (TEL1 to TEL4) can operate the alarm remotely. Factory default instruction texts are shown in the following table. The instruction texts can be changed by SMS text editing, see part 10.
If an SMS is sent from an unauthorized phone (other than TEL1 to TEL4), a valid user code must be entered before the instruction (e.g. USER IMO).
SMS text Description
AM
ARM and lock the car
DM
DISARM and unlock the car
IMO
STOP (immobilize) the car (after turning the ignition key off)
UNIMO
Unblock (mobilize) the car
STATUS
Car alarm will reply with status information, e.g. „car reports: Time: 27.01.04 13:04, Status: Armed, Unblocked, Ignition off“.
HELP
The car alarm will reply with a brief list of SMS instructions.
UC uuuu
To change the user code. uuuu is the new user code, up to 8 characters (A –Z & 0 – 9). Factory default user code is USER
CREDIT
To obtain the balance of a prepaid SIM card if used. See 13.7 for details
HF abcdef
Hands-free set adjustment: a – enable calls (0= disabled, 1=enabled) b – auto answer incoming calls (0= disabled, 1=enabled) c – microphone sensitivity 0 to 9, (5) d – speaker volume 0 to 9, (5) e - ringing tone volume 0=mute to 9= max., (5) f – ringing sound 0 to 9, (5)
LOCATOR
To obtain the car location from the GSM provider. See 13.6 for details.
• The parameters in bold are factory defaults. • The instruction must contain spaces as shown in the table • Only basic ASCII can be used in the SMS instruction texts • If the SMS text contains the % sign, then the following text will be
ignored. Characters %% in the message stop processing the following text. Using these characters is suitable when sending an SMS from an internet gateway which ads another text – advertisements etc. When using the % character it is always necessary to insert the Master or User code followed by a space before the command itself.
9.3 Internet remote control After you register the alarm on the www.GSMLink.cz
web site (see 11),
you can access your alarm remotely from the internet. Using this access you can obtain the status of your car, you can arm, disarm and you can also stop the car after it was stolen. It is also possible to view the memory of the alarm. Installers can change the settings of the alarm remotely using the internet access. 9.3 Dialing-in remote control If enabled by the DIP parameters (see 7), the car alarm can be armed and disarmed remotely by dialing in from an authorized phone (TEL1 to TEL4). The car alarm will not answer the incoming call, but when it recognizes your number, it will change status (Arm or Disarm). Such remote control is free of charge since the phone is not answered. Warning – if you dial your car alarm accidentally it can cause disarming of the alarm.
9.5 Phone calls by installed hands free set
If the optional HF-03 hands free set is installed, it is possible to receive and make phone calls via the car alarm. When your car is disarmed and ignition key is on, the remote control (RC-40) allows you to operate the hands free set. Incoming calls – to answer them, press any button on the RC-40 remote control. By pressing any button again, the call will be terminated. When armed, all incoming calls are automatically rejected. If the car is blocked (by IMO instruction) all calls are automatically answered (it is possible to listen and to speak to the car remotely). Automatic call answering while you are driving can also be enabled by the HF instruction (see 9.2). To make a call – you can call up to 4 preprogrammed numbers while you are driving. By pressing button A, B, 1 or 2 on the remote control you will dial the corresponding number (pre programmed by DIALA to DIAL2, see 6.1) 9.6 Alarm When an alarm is triggered, the siren will sound for 30 sec., warning SMS messages will be sent to all phones (TEL1 to TEL4) and these phones will also be called with the siren sound. To stop the alarm, disarm the alarm by pressing the B button on the
remote control or by disarm SMS instruction (DM).
10 SMS text editing
The SMS texts (alarm information and instructions) are factory
preprogrammed. However, it is possible to change these texts by a mobile phone or via internet access www.GSMlink.cz
To change a text by your mobile phone, send SMS: