J2 615 Integrated Touchscreen Computer System Manual March 2010
Copyright © 2009, 2010 J2 Retail Systems Change history Version 0.1 to Version 1.0 1: Fix cable pin out RJ45 to DB25 J2 Serial Cable, RTS DB25 pin wrong, DB25 SD and RD signals marked wrong. 2: Fix cable “Pin-out when using 8 wire CAT5/6 cable”, RTS DB25 and DSR pin wrong, DB25 SD and RD signals marked wrong. 615 System Manual Version 1.
Contents Overview ............................................................................................................................ 5 Specifications ..................................................................................................................... 7 System ................................................................................................................................ 9 Front View ...................................................................................
Optional Items ................................................................................................................. 32 Customer Display Option ............................................................................................... 33 Connecting the Cable for a J2 615/580 customer display............................................. 33 Dip Switch and Software Setting .................................................................................. 33 J2 615/580 UPS .....................
Overview Featuring the Intel 1.6GHz Atom processor and Intel chipset the new J2 615 computer provides outstanding price and performance. Designed with reliability and durability in mind it incorporates a SanDisk 8GB Solid State Drive (SSD) as standard and with its fanless convection cooled system, there are no moving parts to fail. Using ELO touch controllers as well as an ELO resistive touch screen the 615 provides unmatched touch responsiveness and reliability.
J2 615 Intrgrated Touch Screen Computer 615 System Manual Version 1.
Specifications Main board Processor Chipset Intel N270 1.6GHz Atom processor Intel 945GSE/ICH7 chipset System Memory LCD Touch Panel SO-DIMM DDR 533HMz, 1GB Standard, 2 GB optional LCD Size 15” TFT LCD Brightness 250 nits Resolution 1024 x 768 Touch Screen ELO Resistive 5-wire or optional ELO Infrared (IR) Tilt Angle 0゜~ 90゜ Storage SSD or HDD Expansion 8GB SATA SSD in a quick change slot or an 80GB SATA 2.5” HDD Mini-PCI-E Slot One, normally used for an internal 802.
Second Display Customer Display UPS 10.
System The J2 615 uses the same dynamic design as the J2 580 and J2 650 computers. This allows for different systems to be integrated at the same customer site, maintaining a well balanced look and feel for your important installations. Front View MSR Power LED Rear View SSD/HDD Module I/O Ports 615 System Manual Version 1.
I/O Ports The J2 615 has an integrated design with all the electronics “in the head”. I/O ports are accessible in the cable well at the bottom of the unit (please see below): Cash Drawer , VGA LAN USB COM 1 2, 3, 4 ON/OFF BUTTON DC-IN Audio Out Atom Processor The J2 615 uses the new Intel Atom N270 processor which only requires 2.5 watts of power. With a speed of 1.
Solid State Drive / Hard Disk Drive The J2 615 has one drive bay that supports a 2.5 inch SATA SSD or HDD. The standard drive supplied is an 8GB Solid State Drive (SSD). The SSD or HDD can be accessed simply by loosening the one screw on the drive bay panel on the right side of the unit. The drive can now easily be slid into or out of the drive bay. SSD/HDD Access The J2 615 is the first product on the market to come standard with a SSD drive as opposed to a HDD.
Touch Screen The J2 615 uses an ELO touch control screen paired with the ELO five-wire touch screen rated at 35 million touches per point. As with all J2 designed products using resistive touch screens, the 615 unit includes a water tight gasket for spill resistance. The ELO Infrared (IR) is also available for the J2 615 as an option. The IR touch screen has no known failure mode-- it does not “wear out.” With a protective cover over the LCD panel the IR touch screen does not reduce LCD panel brightness.
LCD Display The LCD display for the J2 615 computer is a 1024 x 768 resolution display with 16.2 Million colors. The brightness is rated at 250cd/m2. The Intel controller allows for the display to be rotated to 0, 90, 180 or 270 degrees without any loss of performance. Secondary Display Port A secondary video display is supported on the J2 615 and can be set as the primary or secondary display. Secondary video displays can be configured as a Twin, Intel Dual Display Clone or Extended Desktop.
USB ports The J2 615 has four external and two internal USB 2.0 ports. The four external ports are located in the cable well. In addition there are two internal USB ports used as follows: one is used for the optional Finger Print Reader and is located on the MSR connecting point; the second internal USB port is used for the IR touch screen controller in the IR version of the 615 unit. USB Ports Ethernet Connection The J2 615 uses the Realtek 8111 Gigabit Ethernet controller.
Both serial ports 3 and 4 can have jumpers set to select for either +12 volts or +5 volts. J2 does not recommend using +5 volts devices if it can be avoided, as it is quite easy to damage a +5 volt device by plugging it into a port supplying +12 volts. Most all serial scanners are available in the + 12 volt version. If a +5 volt device is used, it is recommended that it is clearly marked as such. The maximum current is 500ma and is over-current protected. Serial Ports 615 System Manual Version 1.
RJ45 to DB9 J2 Adaptor Cable RJ45-10 Pin DB9 Signal Pin 1 ----Pin 2 Pin 1 DCD Pin 3 Pin 6 DSR Pin 4 Pin 2 RD Pin 5 Pin 7 RTS Pin 6 Pin 3 SD Pin 7 Pin 8 CTS Pin 8 Pin 4 DTR Pin 9 Pin 5 GND Pin 10 Pin 9 RI Pin-Out 8 pin adaptor when using CAT5/6 cable RJ45- 8 Pin DB9 Signal ------Pin 1 Pin 1 DCD Pin 2 Pin 6 DSR Pin 3 Pin 2 RD Pin 4 Pin 7 RTS Pin 5 Pin 3 SD Pin 6 Pin 8 CTS Pin 7 Pin 4 DTR Pin 8 Pin 5 GND ------- The J2 Cable Adaptor (supplied) RJ45 to DB25 J2 Serial Pinter Cable Pin-out when using 8 wire CA
Audio The J2 615 uses the Realtek ALC662 HD audio CODEC. The auto line out jack is located in the cable well at the bottom of the unit (see below). Audio Line-out Jack Cash Drawer Port The 615 has one cash drawer port that can support one cash drawer directly, or two cash drawers when using a “Y” splitter cable. The “Y” splitter cable is the same type as would be used with an EPSON printer. The port is located in the cable well and uses the industry standard RJ-11 connector and pin out (illustrated below).
2) Using the J2 supplied Virtual COM port for CE.NET, XP Pro, POSReady and XPE 3) Direct access to the I/O ports: The Virtual COM port driver that is standard on Windows XP Pro, WEPOS and XP embedded maps the cash drawers to COM 6 and COM7. These COM port numbers can be changed by modifying using the J2 virtual port configuration utility. A reboot will be needed for these changes to take effect. To open Cash Drawer One: Send a bell character to the COM6 serial port.
CMOS Reset If it becomes necessary the CMOS memory can be reset to factory defaults by adding the CMOS reset jumper JP6 for a few seconds and then removing it. This would normally only be needed to clear an unknown password from CMOS otherwise the normal BIOS load defaults function could be used. Onboard SSD The onboard SATA4 connector is used for the SSD module when a SSD and HDD (or dual SSD) combo is required. This allows for the use of two SATA storage drives in the J2 615.
Mini PCI-E The onboard Mini PCI Express connector is normally used for the optional internal 802.11n wireless LAN card. Power Supply The J2 615 uses a 65 watt notebook type power supply that is normally mounted in the base of the unit. The power supply is rated with an output of 19 VDC 3.42 Amps and has an input rating of 100-240VAC at 50~60Hz 1.8 Amps maximum. The power supply typically has an efficiency rating of 85% under light loads, with a 90% or better rating under heavy loading.
Power Supply Mounting in Base Typical Power Consumption 615 The typical power consumption of the 615 is much lower that a desktop computer and more comparable to a notebook computer. Using the Intel’s Atom processors and Intel chipset allows for much lower power consumption than previous generations of POS computers. This, when coupled with J2 software power reduction utilities, can greatly reduce the system’s total carbon foot print.
Packing List The following contents should be found in the carton: 1: System 2: AC Power cord 3: Serial RJ45 to DB9 Adaptor 4: Serial Printer Cable Standard Items 1: System with 2: AC power cord 4: Printer Cable 615 System Manual Version 1.
System Installation Counter Top Base The J2 615 is shipped with a counter top base which allows for the head to be adjusted from 0-90°. To remove the integrated head from the base, loosen the thumbscrew located on the back of the unit under the hinge of the counter top base, as shown below. Then lift the head as illustrated: a. Loosen the thumbscrew (1) b. Lift the panel up and separate it from the stand bracket 615 System Manual Version 1.
To mount the J2 615 to the base, do the reverse (as shown below): a. attach the panel to the desk mount hinge bracket and slide it into the position, as shown by the red arrows b. Tighten the thumbscrew to finish the installation 615 System Manual Version 1.
Optional VESA / Wall Mount Bracket Installation The VESA / wall mount bracket has threaded mounting holes (screws provided) for the 75mm VESA standard; and unthreaded holes for the 100mm standard. Using the 100mm hole pattern the bracket can be used by itself as a wall mount bracket. After installing the thumbscrew clip mount bracket to the wall, hang the J2 615 on the bracket. Install screw to secure thumbscrew clip The bracket slides on to the J2 615 mount posts, as shown.
MSR Installation a. Remove the 2 screws b. Connect the cable and tighten the screw c. Slide the MSR into the position and tighten the screws to finish the installation. Be careful not to pitch the cable when installing. 615 System Manual Version 1.
SSD/HHD Access Loosen the screw Slide the SSD/HDD Module (as shown) 615 System Manual Version 1.
Removing the Power Supply Adaptor Remove the two screws to release the adaptor and the bracket. (one screw is under plug) 615 System Manual Version 1.
BIOS Settings Starting the BIOS Setup 1. Turn on or reboot this product. 2. Press the DEL key immediately after the product is turned on or press the DEL key when the following message is displayed during POST (the Power on Self-Test). Press DEL to enter SETUP. 3. The main menu of the BIOS setup is displayed. 4. If the supervisor password is set you must enter it here.
Advanced BIOS Features Integrated Peripherals In this menu the boot order may be changed. This menu allows the HDD port to be disabled as Also the keyboard num-lock can be set as well well as the onboard audio. Under Super IO the as the logo display on boot up. COMM ports IRQ and PORT can be changed. Power Management The default function on the power switch can be set in this menu. The “PWRON After PWR-Fail” controls whether the unit will turn back on by itself after AC power is lost.
Driver Installation Driver Download If you did not purchase your operating system from J2 you may download the drivers for the 615 system from the J2 web site at” http://www.j2retailsystems.com/support/615/. For Windows XP there are five drivers that need to be installed.
Optional Items The J2 615 computer supports all the same option modules (as shown below) on the J2 580 product, and also includes the UPS (not shown below): VESA/Wall Mount Bracket MSR Module (front swipe) Finger Print / MSR-Finger Print Combo iButton / iButton-MSR combo 2X20 Character Customer Display 615 System Manual Version 1.0 March 21, 2010 Secondary Display 12” (also 10.
Customer Display Option Connecting the Cable for a J2 615/580 customer display Cable must be fitted correctly. The end with the shrink sleeve goes into the display, the other end to COM3 or COM4. Normally COM4 power is already enabled on that port.
Command Control SW12 Function ON Depend on SW1~SW11 setting Bypass SW1~SW11 setting, fixed at: " Command type: POS7300, " Baud rate: 9600 OFF " Parity check: None-parity " Demo mode: Disable " International character set: USA, standard Europe International Character Set ID SW SW SW SW SW Character Set 4 5 6 7 11 (20h – 7Fh) 0 ON ON ON ON OFF U.S.A. 1 OFF ON ON ON OFF FRANCE 2 ON OFF ON ON OFF GERMANY 3 OFF OFF ON ON OFF U.K.
J2 615/580 UPS Specifications Batteries Run Time Power In Power Out Data Interface Batteries Type Battery Life Charge Time Charger Type Software Size 1.5 hours for the standard J2 615, run time will vary depending on the application loading 19 Volts DC 13-16.8 Volts DC, 8 amps maximum RS232 cable, RJ45 connector 2 – 4 18650 cell Li-Ion pack with protection circuit 500 full discharge cycles 5 hours from full discharge Smart Microcontroller based XP Standard Generic UPS driver 6” x 3.1” x 1.
Software Setup in XP 1: From the START button run CONTROL PANEL. 2: Double click POWER OPTIONS. 3: Select the UPS tab and click on Select under Details. 4: Under Select manufacturer select Generic. Select the COM port you wish to use in the On port drop down menu. Be sure this port is not used for anything else (printer) or the driver will not install. Select model should be Custom. Click Next>. 615 System Manual Version 1.
5: The default values for the Interface Configuration are what the J2 UPS uses, therefore just click Finish. 6: When returned to the Power Options Properties window, click Apply to save the configuration. It will take a number of seconds to configure. Once done the Details should show Manufacturer: Generic and Model: Custom and the UPS and driver should be working. This can be quickly tested by removing the AC power to the unit.
Status LED There is one green status LED on the UPS. This can be viewed when looking into the top of the base, as shown in the picture below: 615/580 UPS STATUS LED Add picture here The status LED can be used to determine what mode the UPS is running in.
