O P E R A T O R ’ S M A N U A L and Set-Up Instructions for UNI-SWIVEL* * AUGERS J USA-15S USA-15P J. & M. Mfg. Co., Inc. P.O. Box 547 Ft. Recovery, OH 45846 Ph: (419) 375-2376 Fax: (419) 375-2708 JMMAN0101 (Rev. 04/02/09) www.jm-inc.
TO THE DEALER: Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner. The dealer must complete the Warranty Registration Card attached to the front inside cover of this manual and return to J. & M. Mfg. Co., Inc. at the address indicated on the card. Warranty claims will be denied if the Warranty Registration Card has not been completed and returned.
UNI-SWIVEL HYDRAULIC AUGERS SPECIFICATIONS SPECIFICATIONS USA-15 Diameter 6” Sizes - Length 15’ Hopper Adjustable to fit almost any make gravity box Auger Tube 14 Ga.
GENERAL INFORMATION BOLT TORQUE CHART Always tighten hardware to these values unless a different torque or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
TABLE OF CONTENTS INTRODUCTION 2 EXPRESS WARRANTY 2 SPECIFICATIONS 3 GENERAL INFORMATION 3 BOLT TORQUE CHART 4 SAFETY RULES 6 SAFETY SIGNS 7 SET-UP INSTRUCTIONS 8-9 PARTS LIST 10 INITIAL OPERATION, OPERATING INSTRUCTIONS/MAINTENANCE 11 SERVICE RECORDS 12 5
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be erased by an operator’s single careless act. In addition, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.
50-16 OWNER’S MANUAL SAFETY SIGNS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged or Missing! IMPORTANT: Install new safety signs if the old signs are destroyed, lost, painted over or cannot be read. When parts are replaced that have safety signs, make sure you install a new sign with each new part. New signs are available from the manufacturer or your authorized dealer. Ref.
UNI-SWIVEL HYDRAULIC AUGER INSTALLATION 1 2 Measure the distance between the angle irons to the left and right of the door on your gravity box. Adjust the dimensions of your hopper to best fit between the angle irons. Use (6) - 3/8” x 3/4” hex bolts and lock nuts and 12 washers to fasten the adjusting ends of the hopper to the center base. Use the 3/8” x 1/2” stove bolts and nuts to “plug” holes not used in the adjustment.
UNI-SWIVEL HYDRAULIC AUGER INSTALLATION 3 Attach the winch assembly to the auger bracket (for normal mounting, the winch handle is on the left side of the auger when facing the box) using (3) - 3/8” x 1” hex bolts, flat washers and lock nuts. Attach the end of the cable to the winch using the clip on the side of the winch. Spool several rounds of cable onto the winch drum as per instructions on the winch.
UNI-SWIVEL HYDRAULIC AUGER INSTALLATION 5 Remove the plastic plugs from the hydraulic motor at the base of the auger and attach the two 1/2” hydraulic hoses. (NOTE: The SUPPLY hose will be the one connected directly to the motor valve and the RETURN hose will be the one connected to the motor valve.) Attach the coupler bracket to the brace inside front leg of the gravity box using one 3/8” x 1” bolt and lock nut. Attach hydraulic hoses.
UNI-SWIVEL HYDRAULIC AUGER PARTS LIST # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 USA-15 Part # HS-0405 DL-86 14-CR HS-0405S DL-86V HH-7 6RS-4 6RS-6 6RS-12 HC-6 6ST-12 SF-15 BF-15 PF-15 RA-1 RS-9 WA-1 316C-7 316C-10 316CC 316-P 12-P 3AH CA-12 2C-1 DP-1 TB-2 12-RW 12-RWSS 6TS-42 SS-12 38M-12F 1PRH 516R15 516-P 384JB HHB-1 51617 HW-S HW-L HW-SS HW-LS FAB-1 38112HB 3812SB 381-HB 38LN 3
INITIAL OPERATION / MAINTENANCE WARNING BE CERTAIN THAT ALL POWER IS SHUT OFF BEFORE SERVICING THE HYDRAULIC AUGER. IMPORTANT - Make sure that your tractor delivers a minimum of 9 gallon per minute (1,500 psi), but does not exceed 15 gallon per minute (2,250 psi). At no time should you operate at 15 gallon per minute and 2,250 psi at the same time.
SERVICE / MAINTENANCE RECORD DATE DESCRIPTION NOTES 13
