OPERATORS MANUAL Rev. 4.30.2014 GRAIN CART 525-14W 620-14 J. & M. Mfg. Co., Inc. 284 Railroad Street - P.O. Box 547 Fort Recovery, OH 45846 Ph: (419) 375-2376 Fax: (419) 375-2708 www.jm-inc.
To The Dealer Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists are completed before releasing equipment to the owner. The dealer must complete the Warranty Registration found on the Dealer Portal website located at dealer.jm-inc.com and return it to J. & M. Mfg. Co., Inc. at the address indicated on the form. Warranty claims will be denied if the Warranty Registration has not been submitted. EXPRESS WARRANTY: J. & M. Mfg. Co. Inc.
Specifications C D SPECIFICATIONS H F A B I E L G 525-14W 620-14 Capacity 525 Bushels 620 Bushels Auger, One Vertical 14” Diameter 14” Diameter Unload Time 3.2 minutes 3.7 minutes Wheels (2) 20x26, 21x32, 21x32, 27x32 27x32 or 18x42 or 18x42 Spindles (2) 4 1/2” Diameter 4 1/2” Diameter PTO 1,000 rpm 1,000 rpm Tires (2) 23.1x26, 24.5x32, 24.5x32, 30.5x32 or 30.5x32 or 20.8x42 20.8x42 Tongue Weight Empty 950 lbs. 1,000 lbs. Loaded 1,950 lbs. 2,100 lbs. Total Weight (approx.) 6,300 lbs.
General Information BOLT TORQUE CHART Always tighten hardware to these values unless a different torque or tightening procedure is listed for specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for Metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
Table of Contents 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . To The Dealer 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bolt Torque Chart 6-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Rules ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be erased by an operator’s single careless act. In addition, hazard control and accident prevention are dependent upon the awareness, concern, judgment, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.
Safety Rules ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged or Missing IMPORTANT: Install new safety signs if #SAFETY Part DECALS # Description the old signs are destroyed, lost, painted 1 JM0018044 Operating Instructions over or cannot be read. When parts are 2 JM0010163 Warning, High Pressure replaced that have safety signs, make 3 JM0014979 Warning, General sure you install a new sign with each new part.
Initial Operation and Maintenance WARNING BE CERTAIN THAT ALL POWER IS SHUT OFF BEFORE SERVICING THE GRAIN CART.
Operating Instructions WHEEL NUTS: Are the wheel nuts properly fastened? Torque to 600 Lbs.-Ft. for standard 22mm wheel studs and nuts. Torque to 500 Lbs.-Ft. for 3/4” wheel studs and nuts. Wheel studs and nuts should be checked after each load during initial operation of the cart and then after every 10 hours of use. Failure to do so may damage wheel studs and nuts. Once the seats are damaged, it will become impossible to keep the lug nuts tight.
Operating Instructions (Continued) 4) Be sure that no debris or foreign objects are in the grain cart. 5) Attach the hydraulic lines to the tractor. Two hydraulic lines (green band) operate the inside gate mechanism. Connect these lines to one service outlet on the tractor. Two hydraulic lines (yellow band) operate the folding mechanism of the auger. Connect these lines to a second service outlet on the tractor.
Lubrication Service Schedule IMPORTANT: Your grain cart has grease fittings at all critical points. These should be serviced before the grain cart is put into operation. WARNING BE CERTAIN THAT ALL POWER IS SHUT OFF BEFORE SERVICING THE GRAIN CART PTO & DRIVELINE: The grease fittings on the PTO should be serviced after every 8 hours of use. Service the grease fittings on each of the drive bearings and also the universal joint after every 8 hours of use.
Trouble Shooting WARNING MAKE SURE THAT ALL POWER IS SHUT OFF BEFORE SERVICING THE GRAIN CART. MAINTENANCE AND REPAIR SERVICE WORK TO BE PERFORMED BY QUALIFIED SERVICEMEN ONLY. Trouble... Auger will not return to down position or move from stow position. Hanger Bushing Assembly at the top of the lower auger flighting is hot Possible Cause... Possible Remedy... Dirt in Restrictor (see pg.
Adjusting the Slip Clutch 1) Make sure the tractor is off and the PTO is disengaged. 2) Disconnect the driveline from the tractor. 3) Locate the (6) bolts (Item 8) on the O.D. of the clutch pack. Loosen the bolts until they rotate freely, finger tighten each bolt, and then tighten each bolt one half turn. 4) Attach the implement to the tractor with a hitch pin, and the drive line to the tractor PTO shaft. 5) Start the tractor.
Adjusting the Upper Flighting WARNING MAKE SURE ALL POWER IS SHUT OFF BEFORE ADJUSTING THE FLIGHTING ASSEMBLY If the upper and lower augers to do not properly separate during the unfolding sequence, the upper flighting may need adjusting. Before making adjustment to the upper flighting, check to see if the lugs and drive dogs on the auger assemblies are locking together.
Repair Parts List and Diagrams When performing maintenance work, wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing and head. Follow the Operator’s Manual instructions to ensure safe and proper maintenance and repair. Your local, authorized dealer can supply genuine replacement parts. Substitute parts may not meet original equipment specifications and may be dangerous. WARNING MAKE SURE ALL POWER IS SHUT OFF BEFORE PERFORMING ANY MAINTENANCE OR REPAIR WORK.
Power Take-Off (PTO) Shaft Assembly Weasler Manufactured PTO with New Style Slip Clutch (Since June 1997)(Black in Color) # Description Part. No.
130 Degree Gearbox Assembly For 14” & 16” Diameter Augers (SUPERIOR) # Description Part. No. 1 2 2 3 4 5 6 7 8 9 10 11 12 13 13 14 15 130 Degree Gearbox Complete (H51AES) 18 Tooth Gear, 1.
Upper & Lower Auger Assembly # Description Part. No.
Hitch Assembly # Description Part. No.
Lift Cylinder # Description Part. No. 1 2 3 4 5 6 7 8 9 10 11 12 Hydraulic Hose 1/4” x 160” 1-1/4”-7 Gr5 Z Hex Nut Pac Man Weldment 2-1/2” X 24” Welded Cylinder 3/8” female NPT X 3/8” male NPT 90 degree elbow PC-37 Check Valve 3/8” male NPT X 3/8” female NPT swivel; WITH .062 orifice Hydraulic Hose 1/4” x 21” Hydraulic Hose 1/4” x 176” 3/8” male NPT x 3/8” female NPT x 3/8” female NPT; Street T Cotter Pin 1” X 3.
Door Wheel Assembly # Description Part. No.
Sideboards 525-14 # Description Part. No. 1 525-14 Sideboard Corner JM0012707 2 525-14 Low Sideboard JM0012673 3 525-14 Rear Endboard JM0012675 4 525-14 Sideboard Corner JM0012708 5 525-14 High Sideboard JM0012672 6 525-14 Front Endboard JM0012674 7 Complete Set w/hardware JM0028046 Sideboards 620-14 # Description Part. No.
Light Kit Assembly Ground (White Wire) Tail Light (Brown Wire) Field Light (Black Wire) 18 Amber Flashing & Turn Signal (Yellow Wire) 19 Amber Flashing & Turn Signal (Green Wire) # Description Part. No.
WEIGH SCALE SYSTEM DIGI-STAR 3-Point 12 11 GT-400 GT-460 # Description Part.
WEIGH SCALE SYSTEM Weigh-Tronix 3 Point 12 11 640 915 # Description Part. No.
Roll Tarp Assembly A B C 26 D
Roll Tarp Assembly # Description Part. No. # Description Part. No.
Fully Adjustable Rice Axle # Description Part. No.
Auto-Log Kit # Description Part. No.
Service / Maintenance Record Date Description Notes 30
